我国中部地区大气CO2柱浓度时空分布

基于日本GOSAT及美国AIRS反演数据产品,对我国中部六省大气CO₂时空分布特征进行研究,结果表明：由GOSAT反演的中部地区2010~2013年大气CO₂年均柱浓度由389.36×10^-6增长到396.52×10^-6,年均绝对增长率达2.39×10^-6/a,呈现出冬春季高值、夏秋季低值的季节变化特征,其柱浓度年均值及去长期趋势后的月均值均略低于长三角地区,高于京津冀和东三省地区;其CO₂柱浓度高值区集中在湖南、江西及周边一带,年均绝对增长率为2.01×10^-6,其柱浓度年均值及去长期趋势后的月均值与长三角地区相当,略低于京津冀和东三省地区,由于受地面源汇影响较小,其与GOSAT反演结果相反,可能是由于AIRS反映了对流层中层大气状况,而GOSAT则更多地反映了近地面层大气CO₂变化.     

生物基聚合物PHBV和PLA复合材料在不同介质中的生物降解及其影响因素

传统工艺的塑料生产不仅依赖石油资源的持续开发利用,同时给环境造成了前所未有的压力,近年来生物基聚合物（聚（3-羟基-3-戊酸酯）-PHBV,聚乳酸-PLA）日渐成为传统石油基塑料的替代产品.本文采用呼吸测试手段,旨在揭示均质复合材料在不同环境介质（土壤、熟化堆肥、水体）条件下及有机添加剂（木质素）,无机添加剂（蒙脱石）和天然有机物链增长剂（Joncryl）作用下的生物降解特征.结果表明：当链增长剂Joncryl添加量为5%时,对所有介质PHBV和PLA复合材料产生显著抑制作用.Joncryl添加量为0.2%时,未对所测样品的生物降解行为产生干扰作用.在熟化堆肥介质中,PLA复合材料比PHBV基质混合物的生物降解速率明显降低.有机木质纤维添加剂（榛子壳粉末）单独在聚合物中添加或者和链增长剂Joncryl以及非有机添加剂（Dellite72T）共同作用下都可促进PLA聚合物中各组分的相容连接性.实验结果表明,新型添加剂在不同介质中以二元或三元添加的方式对生物降解过程产生重要影响,该研究将为新型材料使用后的生物降解效应提供理论依据.     

互花米草入侵对长江口湿地土壤碳动态的影响

为了评价互花米草入侵对长江河口湿地土壤碳动态的影响,利用配对的试验设计在长江口崇明东滩湿地的高潮滩和低潮滩各设置1条入侵种互花米草与土著种的配对样线.结果表明,与土著植物相比,互花米草入侵显著增加了长江口湿地的植物碳库、土壤微生物碳、土壤总碳库和有机碳库,而对占土壤总碳库60%以上的无机碳库无显著影响,意味着互花米草入侵导致的土壤总碳库改变主要是通过增加土壤有机碳库来实现的.高潮滩互花米草和芦苇群落的年均土壤呼吸强度分别为（210.02±4.90）,（157.79±6.39）mg/（m²·h）;低潮滩互花米草和海三棱藨草群落年均土壤CO₂排放速率分别为（157.41±5.27）,（110.90±5.16）mg/（m²·h）,表明互花米草入侵显著增加长江口湿地的土壤呼吸.上述结果意味着互花米草入侵同时增加土壤碳输入和碳输出,但入侵也显著增加了土壤碳库表明入侵增加的土壤碳输入显著高于增加的土壤碳输出.本研究表明互花米草入侵可能会增强了长江河口湿地的土壤碳汇强度和固碳能力.但仍然需要长期系统的监测研究,以便全面定量评估互花米草入侵我国滨海湿地的综合生态影响.     

Mercury flows in large-scale gold production and implications for Hg pollution control

Large-scale gold production(LSGP) is one of the five convention-related atmospheric mercury(Hg) emission sources in the Minamata Convention on Mercury. However, field experiments on Hg flows of the whole process of LSGP are limited. To identify the atmospheric Hg emission points and understand Hg emission characteristics of LSGP, Hg flows in two gold smelters were studied. Overall atmospheric Hg emissions accounted for 10%–17% of total Hg outputs and the Hg emission factors for all processes were 7.6–9.6 kg/ton. There were three dominant atmospheric Hg emission points in the studied gold smelters, including the exhaust gas of the roasting process, exhaust gas from the environmental fog collection stack and exhaust gas from the converter of the refining process. Atmospheric Hg emissions from the roasting process only accounted for 16%–29% of total emissions and the rest were emitted from the refining process. The overall Hg speciation profile(gaseous elemental Hg/gaseous oxidized Hg/particulate-bound Hg) for LSGP was 34.1/57.1/8.8. The dominant Hg output byproducts included waste acid, sulfuric acid and cyanide leaching residue. Total Hg outputs from these three byproducts were 80% in smelter A and 84% in smelter B. Our study indicated that previous atmospheric Hg emissions from large-scale gold production might have been overestimated.Hg emission control in LSGP is not especially urgent in China compared to other significant emission sources(e.g., cement plants). Instead, LSGP is a potential Hg release source due to the high Hg output proportions to acid and sludge.     

Seasonal variation and size distribution of biogenic secondary organic aerosols at urban and continental background sites of China

Size-resolved biogenic secondary organic aerosols(BSOA) derived from isoprene and monoterpene photooxidation in Qinghai Lake, Tibetan Plateau(a continental background site) and five cities of China were measured using gas chromatography/mass spectrometry(GC/MS). Concentrations of the determined BSOA are higher in the cities than in the background and are also higher in summer than in winter. Moreover, strong positive correlations(R2= 0.44–0.90) between BSOA and sulfate were found at the six sites,suggesting that anthropogenic pollution(i.e., sulfate) could enhance SOA formation,because sulfate provides a surface favorable for acid-catalyzed formation of BSOA. Size distribution measurements showed that most of the determined SOA tracers are enriched in the fine mode( 3.3 μm) except for cis-pinic and cis-pinonic acids, both presented a comparable mass in the fine and coarse( 3.3 μm) modes, respectively. Mass ratio of oxidation products derived from isoprene to those from monoterpene in the five urban regions during summer are much less than those in Qinghai Lake region. In addition, in the five urban regions relative abundances of monoterpene oxidation products to SOA are much higher than those of isoprene. Such phenomena suggest that BSOA derived from monoterpenes are more abundant than those from isoprene in Chinese urban areas.     

含弹内埋弹舱缩尺模型气动噪声特性研究

目的对含弹的内埋弹舱模型进行噪声仿真和试验研究。方法计算采用"CFD+CAA"的混合方法,采用DDES计算流场,基于M?hring声学类比方法得到测量点的噪声信息。采用该方法与空腔M219标准试验结果进行对比。内埋弹舱吹风试验在全消声室中进行,并采用传声器阵列识别主要噪声源。结果计算与试验得到的不同来流条件下,不同测量点的噪声频谱曲线基本一致。弹舱内最大声压级出现在中间弹翼附近的侧壁上,与声源识别的主要噪声源的位置一致。结论该研究可为内埋弹舱的设计提供参考和技术支持。     

兰州地区大气臭氧时空变化及影响因素研究

本文采用OMI臭氧遥感数据,结合甲醛垂直柱浓度、气象数据以及经济数据,分析了2005~2015年兰州地区臭氧柱浓度时空变化格局,并探索了影响臭氧的新气象因子,总结达到臭氧污染的日照、气压等气象条件,确定影响臭氧柱浓度的主要人为源并确定其限域。结果表明:1)2005~2015年夏季柱浓度值最高,冬季、秋季次之,春季最低;夏季波动幅度最大,其余三季波动幅度较小且平稳。2)11年中,臭氧柱浓度具有较大的波动。2005年至2010年快速增长到最高值331.997 DU。2010年之后,臭氧柱浓度缓慢下降,2014年起有回升趋势。3)OMI遥感数据具有较高的可靠性,并根据AQI的线性关系划分了臭氧柱浓度的污染等级。结果指示了11年大气臭氧空间变化,2005~2009年5年间研究区全区空气质量一直处于良,2010年全区轻度污染,后两年污染逐渐减弱,2013~2015年全区恢复至良。4)根据兰州发展的趋势以及周边城市的关系,划分了兰州经济圈及功能区,并结合臭氧柱浓度空间分布图得出臭氧污染与经济特征的密切关系。5)正弦模型拟合后臭氧柱浓度变化趋势呈不明显的周期性,说明臭氧的人为来源贡献较大。6)创新探索影响臭氧污染的新气象因子(日照、气压等参数),并确定其重要人为源限域。     

典型铅锌矿化区不同土地利用类型土壤重金属污染特征与评价

选取云南者海典型铅锌矿区周边冶炼区（A）、粮食主产区（B）、保护区（C）三个区域土壤为研究对象,分析三个区域内林地（LD）和耕地（GD）土壤pH、总碳（TC）、总氮（TN）、总磷（TP）和5种重金属（Hg、Cd、Pb、Zn、Cu）含量,利用典范对应分析（CCA）研究不同土地利用类型下它们之间的关系,基于系统熵值与重金属生物毒性改进灰色聚类评价法对研究区重金属污染程度进行评价。结果表明,A、B、C三区土壤的5种重金属均超过云南省土壤背景值,且含量A区 > B区 > C区,所有土壤样品Hg、Cd、Pb、Zn、Cu平均含量分别为7.24、1.53、1 794、2 892、210 mg/kg;LD土壤重金属含量普遍高于GD。研究区土壤pH总体呈弱酸性,但A区土壤受矿业活动影响呈弱碱性。TC、TN含量和C/N值均表现出LD大于GD,但TP含量表现为GD显著大于LD （P<0.05）。CCA分析表明LD和GD土壤pH与Cd和Cu呈负相关,与Zn和Pb呈正相关,且pH对重金属含量的影响最大;TC、TP与重金属Cd和Cu在LD土壤中呈正相关,在GD土壤中呈负相关。改进灰色聚类评价结果表明重金属污染程度均表现为LD大于GD;A区污染最严重且均呈重度污染,B区次之,C区污染程度最轻。经比较本文改进的灰色聚类评价法在准确性和灵敏度方面优于传统方法。     

铝合金的实验室盐雾试验腐蚀行为图像特征提取

目的提取铝合金材料在盐雾箱试验中可以表征腐蚀程度的表面形貌图像特征量。方法首先,对采集于表面化学清洗过的试样原始图像进行图像增强等预处理,突出腐蚀部位;其次,基于数字图像处理的分形和小波分解方法提取出分形维数和小波能量特征值。结果与以质量损失量为基础的腐蚀深度特征值进行相关性对比,基于图像分析的特征提取法的准确度和精度比较高。结论该方法可以应用于对试样的腐蚀程度进行定性和定量分析,判断并预测试样的腐蚀速度。     

Monitoring Air Quality in Mountains: Designing an Effective Network

A quantitatively robust yet parsimonious air-quality monitoring network in mountainous regions requires special attention to relevant spatial and temporal scales of measurement and inference. The design of monitoring networks should focus on the objectives required by public agencies, namely: 1) determine if some threshold has been exceeded (e.g., for regulatory purposes), and 2) identify spatial patterns and temporal trends (e.g., to protect natural resources). A short-term, multi-scale assessment to quantify spatial variability in air quality is a valuable asset in designing a network, in conjunction with an evaluation of existing data and simulation-model output. A recent assessment in Washington state (USA) quantified spatial variability in tropospheric ozone distribution ranging from a single watershed to the western third of the state. Spatial and temporal coherence in ozone exposure modified by predictable elevational relationships ( 1.3 ppbv ozone per 100 m elevation gain) extends from urban areas to the crest of the Cascade Range. This suggests that a sparse network of permanent analyzers is sufficient at all spatial scales, with the option of periodic intensive measurements to validate network design. It is imperative that agencies cooperate in the design of monitoring networks in mountainous regions to optimize data collection and financial efficiencies.