VOC气体检测仪在进口废塑料检验中的应用

针对挥发性有机化合物(VOC)气体在现实中的危害,对废物原料检验的标准进行了探讨,对废物原料检验中如何进行VOC检测进行分析并提出建议。     

工业贮池防腐材料及其施工性能

总结了常用的工业贮池防腐蚀处理方法、防腐蚀材料的性能及施工过程和要点,比较了玻璃钢衬里、玻璃鳞片与乙烯基酯树脂混合衬里和耐酸块材砌筑等防腐蚀处理工艺的工艺条件,并介绍了玻璃钢衬里工艺中所用树脂的类型及性能.     

电子垃圾拆解地周边土壤中二(口恶)英和二(口恶)英类多氯联苯的浓度水平

采集了电子垃圾拆解地周边125个点位的151个土壤样品,分析了土壤中4~8氯代二噁英和二噁英类多氯联苯的浓度.表层土壤样品中总二噁英的浓度范围为280~7 010 pg·g-1,平均浓度为1 380 pg·g-1.中层和深层土壤样品中总二噁英的平均浓度分别为表土的63%和38%.表土样品中二噁英毒性当量浓度(以I-TEQ计)范围为1.4~94.8 pg·g-1.根据德国关于毒性当量浓度的指导方针,125个土壤样品中只有19个(15%)可以被认为对人体健康无害,其余85%的土壤需要调查二噁英的来源.如果考虑多氯联苯对毒性当量的贡献,则有98%的土壤需要调查二噁英的来源.主因子分析被用来调查这一地区二噁英的排放源.通过对土壤中二噁英的同系物分布进行分析,发现拆解活动是这一地区热过程二噁英的主要排放源,也是这一地区土壤中二噁英的主要来源.     

Recycling of electronic displays: Analysis of pre-processing and potential ecodesign improvements

This article analyses the current and future end-of-life management of electronic displays (flat screen televisions and monitors), and identifies and discusses possible ecodesign recommendations to improve it. Based on an investigation of the treatment of displays in two typical European recycling plants, key aspects and criticalities of the recycling methods (sorting, dismantling and pre-processing) are identified. Disaggregated data concerning on-site measurements of the time needed to manually dismantle different displays are presented. The article also discusses the potential evolution of end-of-life scenarios for electronic displays and suggests possible recommendations for recyclers, producers and policy-makers to promote resource efficiency in the recycling of such waste products. Data on time for dismantling the displays can be used to build measurers for voluntary and mandatory policies, to stimulate design innovations for products improvement, and to assess possible alternative treatments of the waste during the pre-processing at the recycling plants. Some quantitative product measures (based on the time thresholds for dismantling some key components) are also discussed, including an assessment of their economic viability. These measures can potentially be enforced through mandatory and voluntary European product policies, and could also be extended to other product groups.     

汽车用材料耐久性试验评价技术

分析概述环境条件和环境因素对汽车用的塑料、涂装等材料的影响和国内的现状，介绍国内外有关的评价试验方法和标准及试验技术，对国内提高汽车用材料的耐候性和耐久性水平提出探讨性建议意见。     

包装箱用改性聚乙烯在干热气候中的老化行为

目的研究包装箱用改性聚乙烯塑料在极端气候环境下的老化特征与规律。方法在敦煌试验站对改性聚乙烯进行为期36个月的自然老化试验,分析缺口冲击强度的变化规律,采用扫描电镜、傅立叶红外光谱和凝胶色谱技术分析样品曝晒面的显微形貌、微观结构以及分子量及其分布变化情况。结果户外曝晒3个月时,样品表面出现大量连续裂纹,缺口冲击强度下降约40%,改性聚乙烯在干热环境下的老化以分子链的断链和氧化为主。结论改性聚乙烯在干热气候中老化迅速,其包装制品在使用中应尽可能减少户外曝晒时间。     

Gasification of waste plastics by steam reforming in a fluidized bed

The process of producing synthetic gas from waste plastics by steam reforming was investigated. To evaluate this process, the steam reforming of the oils derived from low-density polyethylene and polystyrene were carried out using a laboratory-scale fluidized bed of Ni-Al₂O₃ catalysts. The performance of gasification in terms of carbon conversion, gas yield, and gas compositions was examined. Although oils derived from plastics contain many kinds of heavy hydrocarbons and aromatics, they were well gasified at temperatures above 1023 K with a steam/carbon ratio of 3.5 and a weight hourly space velocity of 1 h⁻¹. The hydrogen content of the product gas was very high at approximately 72 vol% for polyethylene-derived oil and 68 vol% for polystyrene-derived oil. These compositions agreed well with the values calculated from chemical equilibrium.     

猫道架设与拆除安全技术探讨

猫道为大跨径悬索桥施工必备的临时结构,为主缆架设、索夹和吊索安装、钢箱梁吊装、主缆防护等提供施工操作平台、材料及工具运输通道,从始至终贯穿整个悬索桥上部构造安装施工使用。猫道作业贯穿整个桥梁的上部施工过程,猫道上的作业全部为高空作业,施工人员承受着天气状况、风速、雨水(雨雪)、台风等自然环境影响,猫道的架设与拆除难度大、危险程度高。因此对猫道架设的工艺安全保障;导索过江安全管理及安全技术;猫道承重索架设工艺及安全技术;猫道面层、侧网、扶手绳及横向通道梁的架设;猫道架设施工安全要求作出规范,同时对猫道架设与拆除安全技术作出规定,保证了猫道架设与拆除作业的安全。     

Two-stage thermal gasification of polyolefins

Plastic pellets of polyethylene (PE), polypropylene (PP), and polystyrene (PS) were gasified in a two-stage thermal degradation process. The first stage is the conversion of polyolefins to distilled oils using a melting vessel. In the second stage, the oils from the first stage are gasified using a tubular reactor. The distilled oil yields of PE, PP, and PS in the first stage were 84, 89, 92 wt%, respectively, each at 470°C. The total gas yields of PE, PP, and PS in the second stage were 80, 74, and 6.2 wt%, respectively, each at 800°C. The main components of the product gas for PE and PP were methane and olefins such as ethene and propene. Some aromatic oils, including benzene, toluene, and xylene, were also produced as by-products. The amount of carbonaceous residue, or coke, was very low (less than 1 wt%). By dividing the process into two stages, the coking rate was considerably reduced compared with direct gasification of the polyolefins. Received: July 19, 2000 / Accepted: September 17, 2000     

Biodegradability of degradable plastics exposed to anaerobic digested sludge and simulated landfill conditions

The biodegradabilities of various plastics by anaerobic digested sludge were measured and compared with the biodegradabilities under simulated landfill conditions. Bacterial poly(3-hydroxy-butyrate-co-3-hydroxyvalerate) (PHB/HV; 92/8, w/w), a natural aliphatic polyester, degraded nearly to completion within 20 days of cultivation by anaerobic digested sludge, while synthetic aliphatic polyesters such as poly-lactic acid, poly(butylene succinate), and poly (butylene succinate-co-ethylene succinate) did not degrade at all in 100 days. Cellophane, which was used as a control material, exhibited a similar degradation behavior to PHB/HV. Under simulated landfill conditions, PHB/HV degraded quite well within 6 months. Synthetic aliphatic polyesters also showed significant weight losses through 1 year of cultivation. The acidic environment inside simulators generated by the degradation of biodegradable food wastes which comprised 34 % of municipal solid waste seems to cause the weight loss of synthetic aliphatic polyesters.