壳聚糖处理印染废水的研究

在不同的壳聚糖浓度、pH和温度条件下，采用分光光度法测得吸附后染料的浓度，得到了壳聚糖对染料的最佳吸附条件，结果为：壳聚糖的投入量在红3B为2％，兰2BG和黄3GE为3％时，pH8．4在碱性范围内，温度为50℃效果最佳。其结果将为壳聚糖在印染废水处理提供一定的理论基础。     

水解-接触氧化工艺处理针织染整废水

介绍了采用水解-接触氧化工艺处理针织染整废水,工程运行结果表明：CODcr和色度的去除率分别达到91.3%、88%,最终排放污水达到国家污水Ⅰ级标准.该工艺具有处理效果好、经济、运行稳定等特点,在染整废水处理中具有实用性.     

超高强度钻杆低温断裂性能及裂纹扩展特征研究

超高强度钻杆在冬季低温环境下容易发生脆性断裂事故,为了从断裂力学角度揭示其冷脆现象的本质,采用ZBC2302-D型示波冲击试验机,获得了不同温度下超高强度钢在冲击断裂过程中的力-位移曲线,并对比分析了冲击功、起裂功和裂纹扩展功之间的变化关系。采用国家标准GB 4161—2007中的计算公式,计算了冲击试样的裂纹扩展量Δa和阻抗应力强度因子K_R;同时,引入K_R阻力曲线,得到超高强度钻杆在不同温度下的剩余强度图。结果表明,当冲击试样开始出现裂纹时,随温度降低,钻杆的初始起裂应力有所增加,出现硬化现象。当钻杆出现一定长度的裂纹时,随温度降低,阻抗应力强度因子越来越小,而且降低速度越来越快,剩余强度也表现出相同的变化趋势。随温度降低,材料抵抗裂纹扩展的能力逐渐下降,表明钻杆在低温下更容易断裂。     

高含氮印染废水强化脱氮处理组合工艺

为考察UASB-A/LO/O（缺氧/低氧/好氧）组合工艺的实际应用效果,将该工艺应用到规模为6 000 t/d的实际工程中,考察其对高含氮印染废水处理效果,同时采用微生物高通量测序对A/LO/O工艺中的微生物菌群结构进行解析.结果表明:在前处理废水进水流量为100 m3/h,染色废水进水流量为150 m3/h,同时A/LO/O工艺污泥回流比为50%左右情况下,COD_Cr、NH₃-N和TN的去除率分别达到91.6%、95.5%和73.5%;染色和前处理废水在改良UASB内均实现了高效厌氧氨化,染色废水厌氧出水中ρ（NH₃-N）/ρ（TN）保持在80%以上,前处理废水厌氧出水保持在85%以上;调节UASB运行参数可对VFAs（挥发性脂肪酸）进行有效调控,从而为后段反硝化工艺提供高品质碳源,实现高效脱氮;A/LO/O系统对COD_Cr、NH₃-N、TN有较好的去除效果,其脱氮性能主要靠变性菌门（Proteobateria）发挥作用,该系统中低氧池的微生物种类最为丰富且发生短程硝化反硝化,对污染物去除贡献最大,当低氧池△ρ（COD_Cr）/△ρ（TN）在18.6左右时,TN去除率最高,达到82%.研究显示,该组合工艺对工程中高含氮印染废水的脱氮效果良好.      

短波长X射线衍射技术及在环境工程中的应用展望

介绍了短波长特征X射线衍射无损检测分析原理和方法,无损地测定了预拉伸铝板、高强钢孔挤压件、铝合金搅拌摩擦焊接件等材料部件的内部残余应力、内部物相、内部织构及其分布,并分析讨论了测试结果。该仪器具有体积小,投资少、使用维护方便等优势,展望了该无损检测分析技术在装备环境工程中的应用前景。     

LD2铝合金腐蚀行为研究

LD2铝合金广泛应用于直升机结构中。铝合金构件在服役过程中会承受环境所造成的疲劳损伤,从而大大降低其服役寿命,因此必须要研究该材料的腐蚀行为。利用SEM扫描电镜,结合能谱分析对铝合金腐蚀损伤行为进行了高精度微尺度研究,并在疲劳断口上发现腐蚀坑底部的“隧道”,该腐蚀隧道会使腐蚀损伤评定过于保守,为结构寿命预测带来较大的不确定性。     

航空高强度LY12CZ铝合金腐蚀剩余强度预测

摘要：目的研究LY12CZ铝合金在腐蚀环境下的强度退化规律。方法按ASTM标准对常温下的LY12CZ铝合金进行预腐蚀,测量腐蚀坑的深度,统计腐蚀坑数目,进行数理统计,获得其几何尺寸的分布。利用MTS880试验机进行静拉伸试验。建立腐蚀坑的物理模型,基于腐蚀坑平均特征参数和最大特征参数,利用AFGROW软件进行剩余强度预测。结果剩余强度随着腐蚀损伤加深而逐步减小。结论与实验值对比的结果证明,该方法具有应用价值。     

我国建设内陆核电站对环境的影响

未来十年我国内陆核电将处在快速增长的阶段,本文以内陆核电站发电原理为基础,考察污染产生种类及成因,探讨我国内陆核电站在正常运营情况下可能对环境产生的影响,并思考发展方向。     

A new process of combined pretreatment and dyeing: REST

Use of enzymes in textile processes has many advantages as far as the environmentally friendly processes are concerned. These advantages include water and energy savings, less chemical use, less fabric damage, mild and environmentally friendly process conditions. In this work, C.I. Reactive Yellow 15, C.I. Reactive Red 21 and C.I. Reactive Blue 19 were used to dye untreated woven cotton fabric in a laboratory scale dyeing machine, on a pilot scale jig and on a pilot scale winch by using a single bath combined process, in which various enzymes, namely, amylase, pectinase, and catalase were employed. This new process was named as the “Rapid Enzymatic Single-bath Treatment” (REST), since it was completed almost in half of the conventional dyeing time, and all of the stages, namely, desizing, scouring, bleaching and dyeing were carried out in a single bath without replacing the process water with fresh water until the end of the dyeing. In the REST process, the untreated, starch-sized fabric was first desized by amylase enzyme, and this was followed by a pectinase treatment in the same bath. The fabric was then bleached by H₂O₂ in the same bath, and after the hydrogen peroxide bleaching; the catalase enzyme was added to the bath to remove H₂O₂ residues before reactive dyeing. Without carrying out intermediate washings/rinsings between these processes, the reactive dyeing was carried out in a conventional way in the same bath, and finally, the fabric was taken from the bath and washed out. The colour yield was compared with the dyeings which were carried out conventionally in separate baths. Finally, the REST has many benefits in terms of water saving, reduced process time and energy consumptions compared to the conventional preparatory and dyeing process of cotton fabrics.     

无机-有机复合絮凝剂PST处理印染废水效果研究

以模拟印染废水和实际印染废水为实验对象,检验了一种新合成有机-无机复合絮凝剂(PST)的絮凝效果。结果表明,PST具有良好的絮凝性能。在受试条件下,絮凝效果与絮凝剂投加量、染料浓度有较大相关性。废水的pH值应用范围较宽;搅拌时间对COD去除率和脱色率没有显著影响。采用PST处理广东省高明市某印染厂的印染废水后,COD去除率为75.16%,脱色率为76.18%,处理效果良好,处理成本明显低于目前市场上普遍使用的聚铝等絮凝剂。