高浓度苯酚在石墨电极上电解特性的研究

研制了数据在线采集记录系统对高浓度苯酚在石墨电极上电解过程的循环伏安行为进行了研究。采用连续循环伏安法考察了体系电解的特点,并考察了支持电解质、扫描速率、苯酚的浓度对反应体系的影响。结果表明:峰电流密度与扫描速率的平方根及苯酚浓度呈线性递增关系,支持电解质的添加量在苯酚电解过程存在最佳值,多次扫描过程中峰电流密度有下降趋势。实验推断电解效率下降是由于电极表面被聚合物污染导致,这一现象对电解处理有机物种的系统控制过程具有重要意义。     

利用分子信标和EXO III放大荧光信号快速检测Ag+

设计新型的DNA探针,其主要功能区域包含适配体区域和分子信标互补区域;当无靶标存在时,羧基荧光素（FAM）的荧光被黑洞猝灭基团（BHQ）猝灭,加入靶标后,Ag⁺与适配体区域特异性结合,使得分子信标与其互补区域发生结合,加入EXO Ⅲ后,分子信标被酶解,从而释放Ag⁺/DNA探针复合物用于下一轮反应,同时产生大量的FAM,因此,可以通过荧光的增强来定量检测靶标的含量.评价了该方法的灵敏度和选择性,探究它在实际样品中的表现能力.结果表明,适配体区域与分子信标间隔2个碱基的DNA探针与分子信标结合效果最好,检测的信噪比最大.该方法对Ag⁺的检测最低下限（LOD）为0.1nmol/L,在0.5~200nmol/L范围内,荧光值与靶标浓度成线性关系（R²=0.994）.对实际样品的检测在20~200nmol/L范围内呈线性关系（R²=0.998）,且能很好的从混合样品中区分10nmol/L Ag⁺.该研究建立的快速检测Ag⁺方法具有良好的线性定量能力和操作性能,且灵敏度高、特异性强,可满足现实的需求.     

Performance and mechanism of Cr(VI) removal by zero-valent iron loaded onto expanded graphite

Zero-valent iron (ZVI) was loaded on expanded graphite (EG) to produce a composite material (EG-ZVI) for efficient removal of hexavalent chromium (Cr(VI)). EG and EG-ZVI were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy and Brunauer–Emmett–Teller (BET) analysis. EG-ZVI had a high specific surface area and contained sub-micron sized particles of zero-valent iron. Batch experiments were employed to evaluate the Cr(VI) removal performance. The results showed that the Cr(VI) removal rate was 98.80% for EG-ZVI, which was higher than that for both EG (10.00%) and ZVI (29.80%). Furthermore, the removal rate of Cr(VI) by EG-ZVI showed little dependence on solution pH within a pH range of 1–9. Even at pH 11, a Cr(VI) removal rate of 62.44% was obtained after reaction for 1 hr. EG-ZVI could enhance the removal of Cr(VI) via chemical reduction and physical adsorption, respectively. X-ray photoelectron spectroscopy (XPS) was used to analyze the mechanisms of Cr(VI) removal, which indicated that the ZVI loaded on the surface was oxidized, and the removed Cr(VI) was immobilized via the formation of Cr(III) hydroxide and Cr(III)–Fe(III) hydroxide/oxyhydroxide on the surface of EG-ZVI.     

电流探头分析设计

分析了电流探头的两大技术指标,传输阻抗及传输阻抗宽频平坦度,并从电流探头物理结构模型出发,构建了电流探头的电路模型,推导出传输阻抗的计算公式,并从电路模型出发,分析了绕线电阻、端接电阻、分布电容对传输阻抗的影响。     

Interfacial forces between silica surfaces measured by atomic force microscopy

Colloidal particle stability and some other interfacial phenomena are governed by interfacial force interactions. The two well known forces are van der Waals force and electrostatic force, as documented by the classical Derjaguin, Landau, Verwey, and Overbeek (DLVO) theory. Moreover, advances in modern instrumentation and colloid science suggested that some short-ranged forces or structure forces are important for relevant colloidal systems. The interfacial and/or molecular forces can be measured as a resultant force as function of separation distance by atomic force microscopy (AFM) colloid probe. This article presents a discussion on AFM colloid probe measurement of silica particle and silica wafer surfaces in solutions with some technical notifications in measurement and data convolution mechanisms. The measured forces are then analyzed and discussed based on the ‘constant charge’ and ‘constant potential’ models of DLVO theory. The di erence between the prediction of DLVO theory and the measured results indicates that there is a strong short-range structure force between the two hydrophilic surfaces, even at extremely low ionic concentration, such as Milli-Q water purity solution.     

一种新型石墨电极的制备及其对苯酚的去除

为了探索一种对有机废水处理有效、廉价、来源广泛、环境友好的电极,以石墨、环氧树脂、固化剂和丙酮为原料,研究制备了一种新型石墨电极 (NGE). 分别采用热水浸泡、乙醇溶液回流、丙酮回流、超声-丙酮回流以及电化学法对制备的石墨电极进行预处理,前三者效果较差,超声-丙酮回流可改善处理效果,但不够理想,电化学法可取得满意的效果.苯酚降解的UV光谱分析表明,尽管商品石墨电极 (CGE) 比NGE具有更高的苯酚氧化效率,但其电解液积累大量的苯醌,而NGE电解液中苯醌积累量少,并且电解过程中逐渐降低. NGE比CGE具有更好的TOC去除效果,两者TOC去除率分别为40%和31%. SEM分析结果表明,CGE被严重腐蚀,NGE无明显变化,表现出良好的稳定性.     

基于数字图像相关方法的石墨高温杨氏模量测试

目的为了得到石墨在高温环境下的杨氏模量,为飞行器热防护系统和高温热结构的设计提供可靠的技术保障。方法基于数字图像相关(DIC)方法和通电电阻加热技术,建立一套测量材料在高温环境下力学性能的测试系统。利用该系统,测量高温下石墨试样的表面应变场和应力-应变曲线,计算相应温度下的杨氏模量。在1400℃实验环境下,采用基于DIC与高温引伸计的方法同时测量超高温陶瓷试件的拉伸应变数据,并进行比较验证。结果在1400℃实验环境下,采用基于DIC与高温引伸计方法测得超高温陶瓷的应变-时间曲线吻合良好,方差为1.3×10-7。1200~1900℃高温环境下,石墨的杨氏模量随温度的升高呈线性增长趋势。结论采用基于DIC方法准确有效,该方法可方便快速地实现对石墨材料在高温环境下杨氏模量的测量。另外,该方法也可应用于其他导电材料杨氏模量的测试。     

石墨探针采样/石墨探针炉原子吸收光谱测定APM中痕量铜

采用一定规格的石墨探针可直接收集大气微料物质（ＡＰＭ）。然后,立即采用石墨探针炉原子吸收光谱测定收集在探针上的ＡＰＭ中痕量铜。方法简便,快速。在０－５５０ｎｇ／ｍＬ范围内,铜的浓度与峰面积吸光度呈良好的线性关系。铜的特征量为２２．０ｐｇ,检出限为６．６ｎｇ／ｍＬ。分析标准参比材料,铜的回收率达９８％,相对标准偏差为３．３％。     

石墨探针收集/石墨探针炉原子吸收法直接测定APM中痕量铅

研究一种直接收集并测定大气微粒物质中痕量有害元素铅的新方法,石墨探针直接收集ＡＰＭ后,用石墨探针炉原子吸收法直接测定收集在探针上的ＡＰＭ中痕量铅。方法特征量为４４．００ｐｇ,检出限为４８．３６ｐｇ,,相对标准偏差为３．２２％,铅学度与峰面积吸光度在０－２５０μｇ／Ｌ范围内呈线性关系,测定标准参比材料,其回收率为９４．４２％＿９９．１４％,并成功地测定了大气微粒物质中痕量铅的含量。     

石墨炉原子吸收分光光度法测定地表水中硒的研究

研究了石墨炉原子吸收分光光度法测定地表水中硒过程中灰化电流的选择和加入基体改进剂减少干扰并提高灵敏度的方法。