Comparative study on performances of a heat-pipe PV/T system and a heat-pipe solar water heating system

The heat-pipe solar water heating (HP-SWH) system and the heat-pipe photovoltaic/thermal (HP-PV/T) system are two practical solar systems, both of which use heat pipes to transfer heat. By selecting appropriate working fluid of the heat-pipes, these systems can be used in the cold region without being frozen. However, performances of these two solar systems are different because the HP-PV/T system can simultaneously provide electricity and heat, whereas the HP-SWH system provides heat only. In order to understand these two systems, this work presents a mathematical model for each system to study their one-day and annual performances. One-day simulation results showed that the HP-SWH system obtained more thermal energy and total energy than the HP-PV/T system while the HP-PV/T system achieved higher exergy efficiency than the HP-SWH system. Annual simulation results indicated that the HP-SWH system can heat the water to the available temperature (45°C) solely by solar energy for more than 121 days per year in typical climate regions of China, Hong Kong, Lhasa, and Beijing, while the HP-PV/T system can only work for not more than 102 days. The HP-PV/T system, however, can provide an additional electricity output of 73.019 kWh/m², 129.472 kWh/m², and 90.309 kWh/m² per unit collector area in the three regions, respectively.     

摆管淋水试验装置的校准方法探讨

文中简述了摆管淋水试验装置的基本结构及其常见的校准方式,对其中的“摆角校准”这一技术难点提出了可行的解决方案并作了较详尽的说明分析。     

Evaluation of environmental feasibility of steel pipe sheet pile cutoff wall at coastal landfill sites

An evaluation method that can express the local leakage of leachate from joint sections in steel pipe sheet pile (SPSP) cutoff walls is discussed in this study. In particular, the evaluation of environmental feasibility (containment of leachates containing toxic substances) considering a three-dimensional arrangement and hydraulic conductivity distribution of the joint sections in the SPSP cutoff wall is compared with an evaluation that uses the equivalent hydraulic conductivity. This equivalent hydraulic conductivity assumes that the joint section and the steel pipe are integrated; therefore, the hydraulic conductivity is substituted with a uniform permeable layer. However, in an evaluation that employs the equivalent hydraulic conductivity, it is difficult to consider the local leakage of leachate containing toxic substances from the joint sections in the SPSP cutoff wall. It was established that evaluations of the environmental feasibility of SPSP cutoff walls with joint sections must take into account the local leakage of leachates containing toxic substances from the joint sections. Also, it was clarified that technologies that lower the hydraulic conductivities of joint sections in SPSP cutoff walls and also facilitate the use of sparser joint arrangements contribute significantly to increasing the environmental feasibility of SPSP cutoff walls at landfill sites.     

城市给水管网优化设计研究

研究了几种典型的城市给水管网优化设计数学模型,并给出了求解方法,指出在给水管网系统的优化设计中进一步完善广义简约(GRG)算法的必要性.     

推行清洁生产 预防工业污染

推行清洁生产是环境保护政策政策的发展趋势,是协调经济发展与环境保护的重要对策。文章综述了末端治理存在的种种弊端,提出了实现清洁生产的主要途径。     

pH值、硫酸根和温度对钢管管垢中铬释放的影响

以市政供水管网钢管管垢为研究对象,将垢层由外向内分为表层、硬壳层和疏松多孔层.利用SEM、BET、XRD、XPS和分形态提取等技术对预吸附Cr(Ⅵ)前后的各层管垢进行表征和分析,并探究了pH值、SO₄^2-浓度和温度对各层管垢中Cr释放的影响.结果显示,钢管各层管垢的主要成分均为α-FeOOH,吸附性能排序为表层>疏松多孔层>硬壳层,管垢中铁元素大多以三价和二价形式存在,具有一定还原性.Cr(Ⅵ)通过物理和化学吸附富集于管垢,主要以铁锰氧化物结合态存在,表层管垢富集量最大.酸性环境、SO₄^2-浓度和温度的升高均会促进Cr的释放.强酸性条件下表层Cr释放浓度为中性条件下的2.76倍;SO₄^2-浓度增加使各层管垢的Cr释放量增加0.1～0.4倍;温度升高20℃,表层管垢的Cr释放量增加26.74%.     

外力作用下管道内表面缺陷处裂纹扩展研究

为提高油气管道安全风险评估的准确性,以含内表面缺陷管道为研究对象,利用ABAQUS软件线弹性及弹塑性分析不同尺寸缺陷对裂纹萌生特征的影响;采用扩展有限元法,建立管道3点弯曲模型与全尺寸静载物理试验,并非线性拟合裂纹扩展尺寸,研究内表面缺陷处裂纹扩展情况.研究结果表明:内表面缺陷中心处极易萌生裂纹,随着缺陷尺寸的增大,裂...     

碎石土边坡破坏机理的敏感性分析

在碎石土类边坡中常常发育稳定的地下水管网排泄系统,它们对控制地下水水位上升,保持边坡稳定十分重要。以官家滑坡为例,通过对滑坡稳定性系数有关的各因素敏感性分析,发现地下水是影响边坡变形破坏以及复发破坏的最主要因素。当坡脚开挖或坡体堆载时,会破坏管道状地下水排泄系统,降雨入渗导致地下水水位升高,从而引起坡体内孔隙压力比、水头高度和水力坡度增大,使潜在滑面上的孔隙水压升高,影响碎石土边坡的稳定性;同时,地下水位的升高降低了土体的内摩擦角,而因素敏感性分析发现,内摩擦角对边坡失稳具有极其重要的影响。在官家滑坡的后期治理中,治水作为主要工程措施的理念已经得到很好的贯彻,效果十分明显。     

小直径锥形管成形工艺研究

通过对小直径锥形管的工艺分析 ,介绍了一种成形的工艺方法和措施 ;并就成形、加工模具作了详细说明     

竖直弯管中含固体颗粒分散泡状流冲蚀预测

目的研究竖直弯管在含固体颗粒分散泡状流下的冲蚀规律,探究管内气液分布、颗粒分布及三维冲蚀形貌之间的关系。方法提出基于VOF模型和DPM模型的瞬态冲蚀数值计算方法,利用Oka等人提出的冲蚀模型及Grant和Tabakoff提出的颗粒-壁面碰撞模型计算管壁冲蚀速率。结果基于VOF和DPM模型的CFD冲蚀计算结果与经验模型及简化CFD模型的计算结果相比,更接近实验值。分散泡状流中,固体颗粒大部分分散在液相中,管道不同截面处的含液率与颗粒粒含量相关性较大,下游直管段和弯头处固体颗粒的粒含量大于上游直管段。含固体颗粒弯管在分散泡状流作用下,冲蚀区域较大,冲蚀最严重位置出现在弯头出口处附近。结论含砂分散泡状流冲蚀条件下,竖直弯管冲蚀形貌与管内气液固分布直接相关,多相流冲蚀瞬态仿真方法可较准确计算气液固分布并预测管道冲蚀。