最大剪切模量对土动力参数及地震反应的影响

最大剪切模量是影响土的动剪切模量比、阻尼比和土层地震反应的最重要参数之一。通常采用室内应变法来确定最大剪切模量，给出土的动剪切模量比和阻尼比，而采用现场剪切波速法求得的结果则很少见。研究了剪切波速法和应变法所确定的最大剪切模量对土动剪切模量比、阻尼比和土层地震反应的影响，推导了两种方法所确定的动剪切模量比和阻尼比之间的关系式。结果表明：最大动剪切模量对土的动剪切模量比、阻尼比和土层地震反应的影响很显著。     

低周荷载下型钢混凝土柱抗剪性能智能分析

为了研究型钢混凝土短柱的抗震性能，通过21根SRC柱在低周反复荷载作用下的剪切黏结破坏试验结果，在利用灰色关联理论进行模型输入变量选择的基础上，建立了其基于改进神经网络模型的受剪承载力分析模型，进而研究了混凝土抗压强度、腹板宽度、轴压比及箍筋间距等因素对SRC柱抗剪能力的影响规律，并对SRC柱的受剪承载力进行了预测。结果表明，所提方法能够反映受剪承载力与影响因素间的非线性变化规律，可供SRC柱在低周往复荷载作用下的受剪承载力分析参考。     

Physical Modeling of Emissions from Naturally Ventilated Underground Parking Garages

The dispersion of pollutants from naturally ventilated underground parking garages has been studied in a boundary layer wind tunnel. Two idealized model setups have been analysed, one was simulating pollutant dispersion around an isolated rectangular building and one was representing dispersion in a finite array of idealized building blocks. Flow and dispersion close to modelled ground level emission sources was measured. The results illustrate the complexity of the flow around buildings and provide insight in pollutant transport from ground level sources located directly on building surfaces. As a result, areas critical with respect to high pollutant concentrations could be visualized. Particularly, the results show high concentration gradients on the surface of the buildings equipped with modelled emission sources. Inside the boundary layers on the building walls, a significant amount of pollutants is transported to upwind locations on the surface of the building. The paper documents the potential of physical modelling to be used for the simulation and measurement of dispersion close to emission sources and within complex building arrangements.     

Experimental Study of the Criteria of Flow Laminarization in Two-Dimensional Dense Gas Plumes

Laminarization of flow in a two-dimensional dense gas plume was experimentally investigated in this study. The plume was created by releasing CO₂ through a ground-level line source into a simulated turbulent boundary layer over an aerodynamically rough surface in a meteorological wind tunnel. The bulk Richardson number (Ri_*), based on negative plume buoyancy, plume thickness, and friction velocity, was varied over a wide range so that the effects of stable stratification on plume laminarization could be observed. A variety of ambient wind speeds as well as three different sizes of roughness arrays were used so that possible effects of roughness Reynolds number (Re_*) on plume laminarization could also be identified. Both flow visualization methods and quantitative measurements of velocity and intermittency of turbulence were used to provide quantitative assessments of plume laminarization.Flow visualization provided an overall picture of how the plume was affected by the negative buoyancy. With increasing Ri_*, both the plume depth and the vertical mixing were significantly suppressed, while upstream propagation of the plume from the source was enhanced. The most important feature of the flow revealed by visualization was the laminarization of flow in the lower part of the plume, which appeared to be closely related to both Ri_* and Re_*.Measurements within the simulated dense gas plumes revealed the influence of the stable stratification on mean velocity and turbulence intensity profiles. Both the mean velocity and turbulence intensity were significantly reduced near the surface; and these reductions systematically depended on Ri_*. The roughness Reynolds number also had considerable influence on the mean flow and turbulence structure of the dense gas plumes.An intermittency analysis technique was developed and applied to the digitized instantaneous velocity signals. It not only confirmed the general flow picture within the dense plume indicated by the flow visualization, but also clearly demonstrated the changes of flow regime with variations in Ri_* and Re_*. Most importantly, based on this intermittency analysis, simple criteria for characterizing different flow regimes are formulated; these may be useful in predicting when plume laminarization might occur.     

苏南地区CO2本底浓度及源汇特征

基于2015~2018年苏州张家港站CO₂在线观测数据，采用时序检查、选取稳定性数据、异常值剔除等质量控制方法获得可靠数据，并通过平均移动过滤（MAF）本底筛分法获得本底数据，讨论苏南地区CO₂变化特征.结果发现：CO₂本底浓度日变化为单峰结构，谷值和峰值分别出现在下午15：00和凌晨5：00前后；季节变化为双峰结构，峰值分别出现在12月和4月；日、季节变化的分布特征均与陆地生态系统、气象条件和人类活动有关.此外，2015~2018年CO₂浓度呈逐年上升趋势，抬升浓度占比逐年增加，吸收浓度占比波动较小，表明人类活动对CO₂浓度的影响正在逐年增加；而陆地生态系统对CO₂吸收汇的作用则相对稳定.源汇分析显示，CO₂抬升浓度随季节小幅波动；吸收浓度则夏半年较低，冬半年较高；抬升浓度日变化为单峰结构，谷值和峰值分别出现在15：00和8：00前后，早晨正值上班高峰，机动车排放可能为早晨峰值的主要因素；吸收浓度日间低、夜间高，这主要与植物光合作用及对流输送有关.分析CO₂浓度与风的关系发现，所有季节静风情况下，CO₂浓度偏高均最为明显，大部分方向CO₂浓度高低与风速大小有明显的负相关，其中S~WNW方向偏高最为明显，这可能是因为SW~NW方向主要为内陆城市群，且测站周边建筑区主要位于W~N方向，弱风有利于本地排放累积的结果.此外，WNW方向风速较大时浓度仍偏高明显，可能与测站W~N方向为建筑区及内陆城市群有关；而测站偏东方向主要为农田和林区，受人类活动影响较小，且海上气流较为洁净，故偏东风较弱时浓度也不高；说明了CO₂浓度除了与风速大小有关外，与周边下垫面类型及较远距离环境特征（城市群或海洋）也有一定的关系.     

风对定日镜影响的计算流体动力学数值模拟

利用linux系统下软件平台Fluent 6.3的并行计算技术和实用的结构网格划分方法,基于Reynolds 时均方程,分别采用两种湍流封闭模型:标准k-ε和MMK修正的k-ε模型,模拟计算了定日镜结构的平均风压系数、阻力、升力以及力矩系数和平均风流场.分析了定日镜镜体平均风压、平均风流场的分布规律和特点;并将数值计算结果与风洞试验进行了比较.结果表明,基于Fluent 6.3的MMK修正的k-ε模型较之标准k-ε模型有更好的预测效果.     

热浮力及室外风压耦合驱动下高层建筑疏散走廊烟气运动网络模拟分析

火灾发生后,火灾烟气主要通过疏散走廊向建筑的其他部位蔓延.有效控制疏散走廊中的烟气,可以阻止其进一步蔓延到楼梯间.了解火灾烟气在疏散走廊中的运动规律,是控制其蔓延扩散的前提.热浮力和室外风压是烟气在走廊中运动的主要驱动力,研究二者耦合作用对走廊中烟气运动的影响,对进一步弄清火灾烟气的流动规律具有较大的意义.采用网络模拟软件CONTAM 3.0模拟疏散走廊中火灾烟气在上述两种驱动力作用下的运动情况.结果表明,随室外风速增大,疏散走廊中火灾烟气的运动速度增大,远大于单纯热浮力作用时烟气的运动速度;当热浮力和室外风压耦合驱动时,室外风压对烟气运动的影响起主要作用.     

二氧化碳灭火系统扑灭风电机组舱内火灾试验研究

为有效遏制全国多地风力发电机组火灾事故的势头,基于灭火系统在风电机组防火设计中的重要性,提出采用二氧化碳灭火系统对风电机舱进行灭火保护的解决方案。在建造国内首台风电机组火灾模拟试验装置的基础上,通过试验研究二氧化碳灭火系统在常温状态和低温状态下对风电机组火灾的灭火能力。结果表明,该灭火系统能够对风力发电机组进行全淹没灭火保护,适用于空间狭小且结构复杂的风电机舱;在低温条件下,其喷放时间和灭火时间虽比常温状态下长,但灭火效能并未降低。     

基于生命周期评价的风力发电机碳足迹分析

本文以我国市场占用率最高的2 MW双馈式风力发电机为研究对象,采用生命周期评价(LCA)方法,核算其全生命周期过程的碳足迹和总能量需求,分析风力发电机不同生命周期阶段的环境影响,识别其减碳潜力.研究结果表明,风力发电机生产阶段、运输阶段、运行阶段和废弃处理处置阶段的碳足迹(以CO2-eq计,下同)分别为1701 t、61 t、255 t和-325 t;各生命周期阶段的总能量需求分别为10413 GJ、701 GJ、1561.95 GJ和-1081 GJ.风力发电机的碳足迹和总能量需求主要来源于生产阶段,废弃处理处置阶段材料的回收利用有效的降低了生命周期的碳足迹和总能量需求.生产阶段的碳足迹和总能量需求分别占全生命周期碳足迹和总能量需求的101%和90%;废弃处置阶段对碳足迹和总能量需求的贡献为-19%和-10%.每1k Wh风力发电的碳足迹和总能量需求分别为20.7 g和0.14 MJ,风力发电机的能量回收期为0.79年.敏感性分析表明,风力发电机的质量和废弃处置阶段的金属回收率都是风力发电机总能量需求和碳足迹的影响因素.     

基于BP神经网络的矿车运行时矿井摩擦阻力的预测*

为了快速有效地确定矿车等运输设备在巷道内运行时矿井摩擦阻力的变化情况,克服模拟软件计算量和现场实测工作量大的问题,以巷道风流速度、矿车运行速度、阻塞比、矿车长度4个矿车运行时巷道摩擦阻力的影响因素作为切入点,采用动网格技术模拟得到矿车在巷道内运行时有关矿井摩擦阻力的数据,以此为样本构建基于BP神经网络的矿井摩擦阻力预测模型,运用MATLAB软件进行网络训练,并将BP神经网络预测值与FLUENT模拟值进行对比。研究结果表明:BP神经网络结构比较简单,能以较快速度收敛,预测值与模拟值最大误差在7%以内,该神经网络模型用于求解矿车等运输设备在巷道内运行时摩擦阻力的变化情况是可行的。