MnO2/CFP复合电极的制备及电吸附Pb2+特性的研究

电极材料的形貌结构与电化学性能等将直接影响着电吸附效果.本研究将二氧化锰(Mn O2)通过电沉积的方法负载于碳纤维纸(CFP)材料上,制备获得了Mn O2/CFP复合电极.所制得的Mn O2/CFP复合电极电化学性质稳定、电容量高,复合电极的单位质量比电容量可高达360 F·g-1.用此电极对初始浓度为6 mg·L-1左右的Pb2+溶液进行电吸附,考察了电沉积时间、电压、p H值等因素对复合电极电吸附效果的影响.结果表明,沉积时间为500 s、电压值为1.0 V、p H值为5.0的条件下可获得最佳的电吸附效果,电吸附3 h后原溶液中残留Pb2+达到0.01 mg·L-1以下,去除效率高达99%以上.本研究为水中重金属离子的去除提供了新的技术选择.     

贵金属负载TiO_2光催化降解甲苯研究

采用Degussa P25 TiO2粉末,利用光沉积法制备贵金属负载光催化剂M/TiO2(M分别为Pt、Pd、Ag和Au)。通过气相甲苯光催化降解实验考察M/TiO2的光催化活性。实验结果表明:负载1.0 wt%的Pt、Pd、Ag和Au四种贵金属均可提高TiO2光催化降解甲苯的效率,其中Pt/TiO2的光催化活性最佳。循环伏安法(CV)、塔菲尔(Tafel)和Mott-Schottky电化学测试证明Pt的负载抑制光生电子和空穴的复合,提高载流子浓度,进而增强TiO2光催化活性。     

石油污染物对海底微生物燃料电池性能的影响及加速降解效应

海底石油污染物在缺氧环境下导致其生物降解过程缓慢,对海洋环境造成长期危害.本文利用海底微生物燃料电池(BMFCs)原理,尝试通过电催化作用提高海底石油污染物的降解速率.对比测试了含油电池装置(BMFCs-A)与无油电池装置(BMFCs-B)的电化学性能,研究了石油污染物对电池性能的影响;比较了含油通路(BMFCs-A)和断路状态下(BMFCs-C)的石油降解率和细菌聚集量,分析了BMFCs对石油污染物降解的加速作用.结果表明,BMFCs-A和BMFCs-B阳极的交换电流密度分别为1.37×10-2A·m-2和1.50×10-3A·m-2,最大输出功率密度分别是105.79 m W·m-2和83.60 m W·m-2,BMFCs-A装置的抗极化能力增强,交换电流密度提高近9倍,最大输出功率密度提高1.27倍.BMFCs-A和BMFCs-C阳极表面的异养菌数量分别是(66±3.61)×107CFU·g-1和(7.3±2.08)×107CFU·g-1,细菌数量增加了8倍,高的异养菌数量导致石油降解加速进行,BMFCs的石油降解率是自然条件下的18.7倍.BMFCs在电化学性能提高的同时,加速石油污染物的降解.本文同时提出了一种海底微生物燃料电池对石油污染物加速降解的新模式.     

电化学法去除水中氯代有机化合物的研究进展

氯代有机化合物难降解、环境危害性极大，对氯代有机化合物的污染进行治理已成为水污染控制的重要课题。介绍了直接电化学氧化法、间接电化学氧化法、直接电化学还原法和间接电化学还原法用于水中氯代有机化合物处理的机理、研究现状；总结了电化学法去除氯代有机化合物的影响因素，同时指出电化学法在实际应用中存在的问题，并展望了氯代有机化合物电化学处理技术的应用前景。     

富磷上清液铁接触除磷工艺及影响因素

设计了一种由铁碳合金和钝态不锈钢作为电化学腐蚀两极系统的铁接触除磷反应器,首次尝试将铁接触除磷技术用于厌氧富磷上清液的处理.通过对模拟富磷上清液除磷效果的测定与分析,详细探讨了铁接触除磷工艺的影响因素,结果表明,曝气方式宜为间歇曝气,且最优曝气/停歇时间为 60 min/30 min;在进水总磷浓度为 30～50 mg/L范围内,随着磷浓度的升高,总磷去除率随之下降;而随着曝气强度、pH值的升高及水力停留时间的延长,总磷去除率随之升高;随着水温的升高,总磷去除率有波动,水温为27℃时,总磷去除率最大.将铁接触除磷工艺运用到侧流除磷方法中,最终可使出水总磷浓度达到国家<城镇污水处理厂污染物排放标准>(GB18918-2002)中的一级(A)标准.     

电化学法处理高盐苯酚废水的研究

对在氯盐电解质中用电化学方法处理含酚废水进行了研究，着重探讨了盐的种类与浓度、反应温度与溶液：pH、电流密度、苯酚初始浓度及阴阳极转换频率对苯酚去除率的影响。在Na2SO4的浓度为0．2mol／L，NaCl的浓度为0．1mol／L、苯酚初始质量浓度为200mg／L、电流密度为0．04A／cm^2、温度为35℃、pH为12．5、阴阳极转换频率为5min/次及反应时间为200min的条件下，苯酚的去除率为99．5％，COD去除率为5％，CIO^-把苯酚氧化成了其他有机化合物。     

含重金属离子废水治理技术的研究进展

介绍了治理含重金属离子废水的物理法、物理化学法、普通化学法、生化法及电化学法等技术的研究进展；论述了电-生物耦合法处理该类废水的最新趋势；指出将不同治理技术加以耦合，充分发挥不同技术的优点、取长补短，并尽量避免它们之问的相互抑制作用，将是该类废水治理技术的发展方向。     

Methods Currently Used in Testing Microbiological Degradation and Deterioration of a Wide Range of Polymeric Materials with Various Degree of Degradability: A Review

Biodegradation of polymeric materials affect a wide range of industries, information on degradability can provide fundamental information facilitating design and life-time analysis of materials. Among the methods currently used in testing, traditional gravimetric and respirometric techniques are tailored to readily degradable polymeric materials mostly and polymer blends with biodegradable components, but they are not applicable to the new generation of engineering polymers which are relatively resistant to biodegradation. However, electrochemical impedance spectroscopy (EIS) has been tested for monitoring biodeterioration of high strength materials and the technique has very high sensitivity. A wide range of materials including electronic insulation polyimides, fiber-reinforced polymeric composites (FRPCs) and corrosion protective polyurethane coatings have been successfully measured under inoculation of degradative microorganisms using EIS. In addition, the mechanism of degradation of high strength polymers is mainly due to the presence of plasticizers in the polymer matrices. The information on various methods discussed in this review is intended to illustrate a suite of methods for those who are interested in testing biodeterioration of polymeric materials under different environmental conditions and in selecting appropriate techniques for specific applications.     

A Sensitive Electrochemical Impedance Spectroscopy Method for Detection of Polyimide Degradation by Microorganisms

An electrochemical impedance spectroscopy (EIS) technique was evaluated for monitoring microbial degradation of electronic packaging polyimides. The microbial inoculum was a mixed culture of fungi isolated previously from deteriorated polyimides. The active fungal consortium comprised Aspergillus versicolor, Cladosporium cladosporioides, and a Chaetomium species. After inoculation, fungal growth on the polyimides resulted in distinctive EIS spectra indicative of polymer insulation failure, which directly related to polymer integrity. Degradation appeared to occur in a number of steps and two distinctive stages in the decline of film resistance were observed in the inoculated EIS cells within the 2 and 10 weeks after inoculation. The early stage of resistance decrease may be related to the ingress of water molecules and ionic species into the polymeric materials, whereas the second stage probably resulted from partial degradation of the polymers by fungal growth on the polymer film. The relationship between changes of impedance spectra and microbial degradation of the polymer was further supported by scanning electron microscopy (SEM) observations of fungi growing on the surface of the inoculated polyimides. Our data indicate that the EIS can be used in detection of early degradation of resistant polymers and polyimides that are susceptible to biodeterioration.     

溶液pH及电流浓度对电化学法生成羟基自由基降解机制的影响

用电化学稳态极化曲线分析方法讨论了溶液pH值及电流浓度对染料降解脱色的影响.实验结果表明,pH值将影响着阴极反应的方向、电极电位与染料降解脱色的效果.在酸性溶液中有利于过氧化氢的生成,阴极电位较低,但不利于随后的絮凝步骤;在中性溶液中染料降解脱色的综合效果较好,COD_Cr去除率可达80%以上.文中还讨论了电流浓度对降解脱色效果的影响,当电解槽内电流浓度达0.5 A/L时可取得满意的效果,电流浓度太大时,体系将伴随着析出氢气等的副反应,降解反应的电流效率下降.