铜-胺改性ZSM-5吸附剂的制备及其对NOx的净化机理

以ZSM-5分子筛粉体为原料，成型后负载铜盐和有机胺改性，制备出一种高效脱除氮氧化物的吸附剂。通过改变铜盐、有机胺的含量以及铜盐活化温度使吸附剂的性能得到优化，在实验条件下（NO：初浓度1000mg／m^3，气流2．7L／min）床层对NO2动态吸附的透过时间由改性前的3min提高到90min，并使NO气体的释放得到有效减缓。通过动态吸附实验研究了NO释放时间在负载前后的变化，通过X射线光电子能谱（XPS）和红外分析（FTIR）研究了吸附剂表面铜元素、有机基团等在吸附前后的变化规律，提出了可能的净化机理。     

Ultrasound-assistant preparation of Cu-SAPO-34 nanocatalyst for selective catalytic reduction of NO by NH3

The influence of the various preparation methods of Cu-SAPO-34 nanocatalysts on the selective catalytic reduction of NO with NH₃ under excess oxygen was studied. Cu-SAPO-34 nanocatalysts were prepared by using four techniques: conventional impregnation (IM), ultrasound-enhanced impregnation (UIM), conventional deposition precipitation (DP) using NaOH and homogeneous deposition precipitation (HDP) using urea. These catalysts were characterized in detail by various techniques such as N₂-sorption, XRD, TEM, H₂-TPR, NH₃-TPD and XPS to understand the catalyst structure, the nature and the dispersed state of the copper species, and the acid sites for NH₃ adsorption. All of the nanocatalysts showed high activities for NO removal. However, the activities were different and followed the sequence of Cu-SAPO-34 (UIM) > Cu-SAPO-34 (HDP) > Cu-SAPO-34 (IM) > Cu-SAPO-34 (DP). Based on the obtained results, it was concluded that the NO conversion on Cu-SAPO-34 nanocatalysts was mainly related to the high reducibility of the isolated Cu^2 + ions and CuO species, the number of the acid sites and the dispersion of CuO species on SAPO-34.     

γ-Al_2O_3负载Ni、Fe催化剂同时脱硫脱硝

采用浸渍法制备了不同负载量的Ni(x)Fe(y)/γ-AL2O3催化剂,通过XRD、H2-TPR、BET和SEM对催化剂进行表征,使用微型催化反应装置考察催化剂在以CO作为还原气时,同时脱硫脱硝的催化活性。结果表明,Ni O和Fe2O3做为活性组分可以很好地分散在γ-Al2O3载体上,并且不破坏其结构;Ni(8)Fe(2)/γ-Al2O3催化剂有最佳的脱硫脱硝活性,脱硫率达到96.55%,脱硝率达到97.92%。     

Capture of carbon dioxide by amine-impregnated as-synthesized MCM-41

The novel carbon dioxide(CO2) adsorbents with a high capture effciency were prepared through impregnating the as-synthesized MCM-41 with three kinds of amines,namely diethylenetriamine(DETA) ,triethylenetetramine(TETA) and 2-amino-2-methyl-1-propanol(AMP) .The resultant samples were characterized by small angle X-ray diffraction and low temperature N2 adsorption.The synthesis way not only saves the energy or extractor to remove the template but also is environmentally friendly due to the absence of the potential pollutants such as toluene.CO2 capture was investigated in a dynamic packed column.The sample impregnated by TETA showed the highest adsorption capacity,approximately 2.22 mmol/g at 60°C due to its highest amino-groups content among the three amines.The CO2 adsorption behavior was also investigated with the deactivation model,which showed an excellent prediction for the breakthrough curves.     

Heavy metals removal from aqueous solution using carbonaceous K_2S-impregnated adsorbent

A novel carbonaceous adsorbent for heavy metal removal was prepared from raw coal by one-step simple sulfur impregnation using K_2S. Raw coal was mixed with K_2S powder and then heated at 800℃ for 30 min in nitrogen to produce K_2S char. The sulfur content and form in K_2S char were determined, and the ability of K_2S char to adsorb Zn~(2+), Cd~(2+) and Pb~(2+) was examined. The K_2S impregnation was effective at impregnating sulfur into coal, especially in the form of elemental, thiophenic and sulfatic sulfur. The sulfur content of K_2S char was higher than those of raw coal and pyrolysis char. The Zn~(2+) removal in 2.4 mmol/L of Zn~(2+) solution by K_2S char was higher than raw coal with the removal rate of 100%. K_2S char adsorbed Pb~(2+) and Cd~(2+) in 24 mmol/L of Pb~(2+) and Cd~(2+) solution with the removal rate of 97 % and 35 %, respectively. The elution extents of adsorbed Pb~(2+) and Cd~(2+) were zero in distilled water and 27% in 0.1 mol/L HCl solution. These results indicated that an effective adsorbent for heavy metal ions was prepared from coal using K_2S sulfur impregnation, and that the adsorbed metals were strongly retained in K_2S char.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

纳米银负载型阳离子交换树脂的制备及其对水中碘离子的吸附去除

以大孔型磺酸基聚苯乙烯阳离子树脂为载体,采用硝酸银溶液浸渍、硼氢化钠溶液还原制备了纳米银负载型阳离子交换树脂,并对其吸附去除水中碘离子的性能进行了研究。结果表明：最佳硝酸银浸渍浓度为10 mmol/L,对应载银量19.3 mg/g;25 ℃中性水溶液中,该材料对碘离子的饱和吸附量为74.7 mg/g;吸附量受溶液离子强度的影响较小,但当溶液pH从11降至3时吸附量降低了23%。根据吸附前后材料的XPS谱图变化推测碘离子的去除机理可能为：树脂载体上负载的纳米银活性组分首先与水中溶解氧发生氧化反应产生银离子,随后与溶液中的碘离子结合形成AgI沉淀,从而将碘离子从溶液中去除。     

聚乙烯亚胺改性UiO-66-NH2对水中U(Ⅵ)的吸附

采用聚乙烯亚胺(PEI)改性氨基化锆基金属有机骨架材料(UiO-66-NH₂)制备了UiO-66-NH₂/PEI,利用XRD、SEM和FTIR对产物进行了表征,并将其用于吸附水中的U(Ⅵ)。考察了UiO-66-NH₂/PEI吸附U(Ⅵ)的影响因素,并研究了吸附动力学和等温线。实验结果表明:UiO-66-NH₂/PEI对U(Ⅵ)具有良好的吸附效果,PEI与UiO-66-NH₂质量比为30%、溶液pH为6、吸附剂投加量为80 mg/L、吸附时间为120 min、初始U(Ⅵ)质量浓度为10 mg/L时,UiO-66-NH₂/PEI对U(Ⅵ)的去除率达98.2%(303 K下);UiO-66-NH₂/30%PEI对U(Ⅵ)的吸附在60 min内达到平衡,吸附过程符合准二级动力学模型和Langmuir模型,最大吸附量达452.49 mg/g。     

制备方法对Mn-Ce/TiO2催化剂低温选择性催化还原活性的影响

采用溶胶凝胶法、浸渍法以及两者相结合的方法制备了Mn-Ce/TiO2催化剂.运用XRD、BET和SEM等技术对催化剂进行了表征,发现溶胶凝胶法制备的Mn-Ce/TiO2催化剂为锐钛矿结构,具有较大的比表面积,中孔结构丰富,Mn、Ce活性组分在载体表面高度分散或形成了无定形结构.实验研究了催化剂对氨选择性催化还原NO反应的催化性能,结果表明,用溶胶凝胶法制备的Mn-Ce/TiO2催化剂脱硝活性最好,当Mn、Ce负载量为20％,NH3/NO摩尔比为1.1,空速为9 436 h-1,烟气温度为240℃时,NO转化率大于90％.     

浸渍-碱性微波法载磁活性炭粉对壬基酚的吸附

利用浸渍-碱性微波法制备载磁粉末活性炭,通过等温吸附实验和动力学吸附实验,研究对比了其与原料活性炭、浸渍载铁活性炭对壬基酚的吸附性能。采用氮气吸附仪、FTIR、XRD、国标(GB/T12496.19-1999)邻菲啰啉分光度法及VSM,分别对3种样品进行了物相结构、表面官能团、铁含量及磁性能的分析,并探讨了吸附机理。结果表明,浸渍-碱性微波法载磁活性炭的总孔容及孔隙率均有较大提高;其吸附等温线符合Freundich方程,吸附动力学过程符合准二级动力学方程与孔道内扩散模型,相关系数R2均大于0.900。原活性炭经一定浓度的铁盐溶液浸渍后,铁含量由2%提高到8%。在碱性、N2气氛条件下微波后,铁系物主要存在形式为零价铁和Fe3O4,制得的载磁活性炭饱和磁化强度为1.12 emu/g。