γ-Fe_2O_3/膨胀石墨复合材料吸附废水中六价铬的应用研究

介绍了采用溶胶凝胶法合成新型的复合材料-磁性的γ-Fe_2O_3膨胀石墨(MEG)复合材料。通过采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)以及X-光电子能谱仪(XPS)对该复合材料MEG进行了表征,结果表明MEG中γ一Fe_2O_3的粒径约为50nm,而且其中γ一Fe_2O_3和膨胀石墨通过C=O相互作用。复合材料MEG作为新型的六价铬吸附剂,通过吸附时间、初始溶液的pH值以及再生性对该吸附过程进行了考察。结果表明:在40 min内MEG吸附六价铬的过程基本达到平衡;在初始溶液的pH为3.5时,MEG对六价铬的最大吸附量可以达到16.4mg/g;而且该复合材料MEG重复使用3次后吸附效果基本没有下降。因此,复合材料MEG对于废水中六价铬的处理有选择性吸附作用,而且初始溶液的pH值对其吸附过程起着重要作用。     

Vulcan_(42)消解—原子荧光测定土壤和沉积物中的砷汞

建立了全自动样品处理系统Vulcan 42-原子荧光光度法测定土壤和沉积物中砷和汞的方法。准确称取0.2500 g样品,经Vulcan42全自动消解系统消解后,采用原子荧光光度计测定砷和汞的含量。运用该方法砷的检出限为0.11 mg/kg,回收率在96%¹01%之间,相对标准偏差(n=6)在1.3%101%之间,相对标准偏差(n=6)在1.3%⁴.5%之间;汞的检出限为0.003 mg/kg,回收率在90%4.5%之间;汞的检出限为0.003 mg/kg,回收率在90%¹08%之间,相对标准偏差(n=6)在0.5%108%之间,相对标准偏差(n=6)在0.5%⁴.7%之间。     

地表水环境监测进展与问题分析

地表水环境的质量监测对我国水环境保护工作具有非常重要的作用,同时对我国的经济发展有着深远的影响。随着我国经济的快速发展,我国水环境监测工作有了较大的发展,但是在仪器更新、分析能力等方面还存在一系列的问题,本文对地表水环境监测的进展进行了阐述,并分析了水环境监测中存在的问题。     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

快速消解分光光度法测定低浓度水样化学需氧量的不确定度评定

摘要：运用测量不确定度评定的方法和程序,分析了快速消解分光光度法（HJ／T399—2007）测量水质化学需氧量测试过程中不确定度的来源,主要是标准溶液配制、标准曲线拟合、样品重复测定、分光光度计、取水样体积这五部分引入的不确定度。本次测量相对合成不确定度为0．027;最大的相对不确定度分量是标准曲线拟合引起的,相对不确定度为0．015;最小的相对不确定度分量是取水样体积引起的,相对不确定度为0．0032;本次测量结果为：56．0mg／L±3．04mg／L,k=2。     

不同TS浓度互花米草沼渣二次发酵特性研究

中温（35±1）℃条件下,沼渣经6%的NaOH常温下处理48 h后,在TS含量8%、10%、12%的条件下沼气发酵.分析了发酵过程中日产气量、累积产气量、甲烷含量、pH值、挥发性脂肪酸（VFA）的变化,从不同角度考察TS含量负荷对沼渣二次发酵特性的影响.单位TS的日产气高峰分别达10、14、13 mL.g-1,累积产气率为217、227、228 mL.g-1,甲烷含量均在65%以上.发酵过程中最低pH为7.04.乙酸浓度最高分别为3 364、3 286、5 728 mg.L-1,丙酸和丁酸浓度均低于1 100 mg.L-1.结果表明,沼渣为难降解有机物,分解缓慢,不易出现酸化现象,但仍具有较强的产气潜力.     

基于虚拟技术的环境监测仪器设备管理方法

利用虚拟现实、虚拟环境技术,通过人机交互方式,在现实空间之外创造另一个尽可能真实的、互动的模拟世界,使应用者可以直观、随意地观察和管理仪器设备,实现检测仪器全生命周期的运行轨迹记录和过程跟踪,凭其强大的可视性、溯源性和易操作性,较明显地提高仪器设备的利用率与管理水平。     

Anaerobic tapered fluidized bed reactor for starch wastewater treatment and modeling using multilayer perceptron neural network

Anaerobic treatability of synthetic sago wastewater was investigated in a laboratory anaerobic tapered fluidized bed reactor(ATFBR) with a mesoporous granular activated carbon(GAC)as a support material.The experimental protocol was defined to examine the effect of the maximum organic loading rate(OLR),hydraulic retention time(HRT),the efficiency of the reactor and to report on its steady- state performance.The reactor was subjected to a steady-state operation over a range of OLR up to 85.44 kg COD/(m~3.d).The COD removal efficiency was found to be 92% in the reactor while the biogas produced in the digester reached 25.38 m~3/(m~3·d) of the reactor. With the increase of OLR from 83.7 kg COD/(m~3.d),the COD removal efficiency decreased.Also an artificial neural network(ANN) model using multilayer perceptron(MLP)has been developed for a system of two input variable and five output dependent variables. For the training of the input-output data,the experimental values obtained have been used.The output parameters predicted have been found to be much closer to the corresponding experimental ones and the model was validated for 30% of the untrained data.The mean square error(MSE)was found to be only 0.0146.     

ABR处理硫酸盐有机废水的相分离特性研究

为了考察厌氧折流板反应器(ABR)处理含硫酸盐有机废水的相分离特性,采用有效容积为32L的五隔室ABR,通过为期132d的启动试验,研究了启动运行过程中各隔室COD和SO24-降解情况、VFA和S2-分布规律及颗粒污泥微生物相变化状况.结果表明,采用低负荷低增幅方式启动,在132d内成功启动ABR并达到稳定,COD和SO24-的负荷分别由1.5kg·(m3·d)-1逐渐提高到3.3kg·(m3·d-1)和由0.07kg·(m3·d-1)逐渐提高到0.18kg·(m3·d-1),COD和SO24-的去除率分别为95%和85%左右.各隔室COD沿程呈递减趋势,其去除主要由第1、4、5隔室完成,SO42-的去除主要由前面三隔室承担,前面三隔室的VFA和S2-浓度较高,到最后两隔室则急剧降低;随负荷的增加,承担COD及SO42-主要去除作用的隔室后移,前面三隔室的VFA和S2-最高点及最后两隔室的VFA和S2-的急剧降低位置也后移;各隔室的微生物经长期运行驯化后表现出良好的种群配合和高度的特异性,具有明显的产酸相与产甲烷相、硫酸盐还原相与硫单质生成相的分离特征.     

Enhancement of thermophilic anaerobic digestion of thickened waste activated sludge by combined microwave and alkaline pretreatment

Pretreatment of thickened waste activated sludge (TWAS) by combined microwave and alkaline pretreatment (MAP) was studied to improve thermophilic anaerobic digestion efficiency. Uniform design was applied to determine the combination of target temperature (110–210°C), microwave holding time (1–51 min), and NaOH dose (0–2.5 g NaOH/g suspended solids (SS)) in terms of their effect on volatile suspended solids (VSS) solubilization. Maximum solubilization ratio (85.1%) of VSS was observed at 210°C with 0.2 g-NaOH/g-SS and 35 min holding time. The effects of 12 different pretreatment methods were investigated in 28 thermophilic batch reactors by monitoring cumulative methane production (CMP). Improvements in methane production in the TWAS were directly related to the microwave and alkaline pretreatment of the sludge. The highest CMP was a 27% improvement over the control. In spite of the increase in soluble chemical oxygen demand concentration and the decrease in dewaterability of digested sludge, a semi-continuous thermophilic reactor fed with pretreated TWAS without neutralization (at 170°C with 1 min holding time and 0.05 g NaOH/g SS) was stable and functioned well, with volatile solid (VS) and total chemical oxygen demand (TCOD) reductions of 28% and 18%, respectively, which were higher than those of the control system. Additionally, methane yields (L@STP/g-CODadded, at standard temperature and pressure (STP) conditions of 0°C and 101.325 kPa) and (L@STP/g VSadded) increased by 17% and 13%, respectively, compared to the control reactor.