Persistent organic pollutants (PCB, DDT, HCH, HCB & BDE) in eels (Anguilla anguilla) in Scotland: Current levels and temporal trends

Eels are an ideal biomonitor for persistent organic pollutants (POPs) because of their high lipid content, longevity and tendency to remain within a defined range during their freshwater life phase. This study investigated concentrations of POPs in eels (Anguilla anguilla) from 30 sites across Scotland, including polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (BDEs), DDT (and metabolites), hexachlorocyclohexanes (α, β, γ-HCH), hexachlorobenzene (HCB), hexachlorobutadiene (HCBD) and pentachlorobenzene. Despite its EU-wide ban ∼30 years ago, DDT and its derivatives were detected in almost all samples. PCB 153 and 138 were the most widely detected PCB congeners, while BDE 47 was the dominant BDE. Pentachlorobenzene was not detected, while HCBD was detected once only. α-HCH, β-HCH and HCB concentrations were very low (generally <3 μg/kg or below detection). When compared with 1986 and 1995 data, the results revealed considerable decreases in p,p′-DDE concentrations. More drastic reductions were evident for γ-HCH, reflecting the tightening restrictions on pesticide use imposed over the previous decades.     

A/O1/H/O2工艺处理焦化废水硝化过程的实现及其抑制

针对焦化废水中的有毒污染物会对敏感易受干扰的硝化细菌产生不利影响从而破坏硝化过程稳定性的现象,采用A/O1/H/O2工艺处理焦化废水的实际工程为研究对象,根据工程运行的水质监测数据分析,发现几种主要污染物的浓度变化会对二级好氧段的硝化过程产生抑制影响。序批式毒性抑制实验结果表明,苯酚、硫氰化物和喹啉对硝化过程具有毒性抑制作用,半抑制浓度EC50分别为34.26、278.5和73.24 mg/L。当二级好氧工艺段运行正常时（C/N约4.3/1,pH8～8.5,DO 4～4.5 mg/L）,出水氨氮浓度可低于5 mg/L,是由于焦化废水经厌氧/好氧/水解工艺后毒物浓度大幅下降,毒性得到削减,表明焦化废水生物处理A/O1/H/O2组合流化床工艺具有较强抵抗毒物抑制并实现高效的硝化作用。     

炉排炉焚烧垃圾过程中主要污染物的控制

概述了二恶英、重金属、酸性气体、灰渣等垃圾焚烧的主要污染物，以二段式（往复）焚烧炉为例，介绍了炉排炉焚烧处理工艺和污染控制设备。提出通过控制垃圾焚烧条件、尾气处理以及吸附等方法，可以有效控制二恶英类污染物的排放；重金属的控制可以用除尘器或使用相应的吸附剂处理；采用较为成熟的烟气处理技术，可以控制处理酸性气体；灰渣可采用固化稳定化或酸提取法处置。     

Crystal structure of δ-isobutoxypentabromo-cyclododecanes, kinetics and selectivity of their isomerization during thermal treatment of flame-proofed polystyrenes

Hexabromocyclododecanes (HBCDs) are persistent organic pollutants now ubiquitous in the environment. Technical HBCD mixtures and with it flame-proofed polystyrenes (FP-PS) also contain isobutoxypentabromocyclododecanes (iBPBCDs) as minor constituents, which are possibly released together with HBCDs. So far, eight diastereomeric pairs of enantiomers named as α-, β-, γ-, δ-, ?-, ξ-, η-, and θ-iBPBCDs with proportions of 10%, 5%, 2%, 21%, 11%, 11%, 12% and 28% were found in technical HBCD. Herein the crystal structure of racemic δ-iBPBCD, the second most prominent diastereomer, is presented and assigned to (1S)-1-isobutoxy-(2R,5R,6S,9S,10S)-2,5,6,9,10-pentabromocyclododecane and its enantiomer. During thermal treatment of FP-PS, e.g. the production of extruded polystyrenes (XPS), proportions of δ-iBPBCDs decrease and those of other stereoisomers increase. Evidence was found that δ-iBPBCDs isomerize stereo- and regioselectively to β-iBPBCDs. Based on structural and kinetic data, a transformation mechanism was proposed. Apparent first-order rate constants (k_iso) of 0.0019, 0.0050, and 0.012 min⁻¹ are found for the δ- to β-iBPBCD isomerization at 120, 130, and 140 °C, respectively, corresponding to half-lives of 360, 140, and 56 min. These transformations also occur during the production of XPS, which predominantly contain β-iBPBCDs, whereas δ-iBPBCDs dominate in materials experiencing lower thermal stress, e.g. expanded polystyrenes (EPS). The relative configurations of δ- and θ-iBPBCDs are TtCtCt, like the one of γ-HBCDs. γ-HBCDs are the kinetically and α-HBCDs with a TcCtCc configuration the thermodynamically favored products. In analogy, β-iBPBCDs are assumed to have a TcCtCc configuration like α-HBCDs because they are formed from δ-iBPBCDs under thermodynamic control. In conclusion, HBCD- and iBPBCD-patterns in flame-proofed polystyrenes vary substantially, reflecting the thermal stress these materials have experienced. When released to the environment, these patterns might further change, as observed for HBCDs.     

Scaling up a treatment to simultaneously remove persistent organic pollutants and heavy metals from contaminated soils

Soil washing is a treatment process that can be used to remediate both organic and inorganic pollutants from contaminated soils, sludges, and sediments. A soil washing procedure was evaluated utilizing about 100 g samples of soil that had been field-contaminated with arsenic, chromium, copper, pentachlorophenol (PCP), polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs). The highest level of mobilization/detoxification was achieved in three soil washes with a mixture of 0.1M [S,S]-ethyelnediaminedisuccinate ([S,S]-EDDS) and 2% Brij 98 at pH 9 with 20 min of ultrasonication treatment at room temperature. This combination mobilized 70% of arsenic, 75% of chromium, 80% of copper, 90% of PCP, and 79% of PCDDs and PCDFs, so that the decontaminated soil met the maximum acceptable concentrations of the generic C-level criteria regulated by the Ministère du Développement Durable, de l’Environnement et des Parcs for the Province of Québec, Canada.The organic pollutants were back-extracted from the aqueous suspension with hexane. Heavy metals were virtually completely precipitated from the aqueous washing suspension with Mg⁰ particles at room temperature. The PCP was detoxified by catalytic hydrodechlorination with a stream of 5% (v/v) H₂-supercritical CO₂ that transported the organosoluble fraction through a reaction chamber containing 2% Pd/γ-Al₂O₃.In toto, this soil washing procedure demonstrates that persistent organic pollutants and selected heavy metals can be co-extracted efficiently from a field-contaminated soil with three successive washes with the same soil washing solution containing [S,S]-EDDS and a non-ionic surfactant (Brij 98) in admixture. An industrial-scale ex situ soil washing procedure with a combination of a non-ionic surfactant and a complexing reagent seems to be a plausible remediation technique for this former wooden utility pole storage facility.     

Dispersal networks for enhancing bacterial degradation in heterogeneous environments

Successful biodegradation of organic soil pollutants depends on their bioavailability to catabolically active microorganisms. In particular, environmental heterogeneities often limit bacterial access to pollutants. Experimental and modelling studies revealed that fungal networks can facilitate bacterial dispersal and may thereby improve pollutant bioavailability. Here, we investigate the influence of such bacterial dispersal networks on biodegradation performance under spatially heterogeneous abiotic conditions using a process-based simulation model. To match typical situations in polluted soils, two types of abiotic conditions are studied: heterogeneous bacterial dispersal conditions and heterogeneous initial resource distributions. The model predicts that networks facilitating bacterial dispersal can enhance biodegradation performance for a wide range of these conditions. Additionally, the time horizon over which this performance is assessed and the network’s spatial configuration are key factors determining the degree of biodegradation improvement. Our results support the idea of stimulating the establishment of fungal mycelia for enhanced bioremediation of polluted soils.     

Kinetic assessment of persistent halogenated xenobiotics in cell culture models: comparison of mono- and poly-halogenated compounds

We evaluated the suitability of single and multiple cell type cultures as model systems to characterise cellular kinetics of highly lipophilic compounds with potential ecotoxicological impact. Confluent mono-layers of human skin fibroblasts, rat astrocytoma C6 cells, non-differentiated and differentiated mouse 3T3 cells were kept in culture medium supplemented with 10% foetal calf serum. For competitive uptake experiments up to four different cell types, grown on glass sectors, were exposed for 3 h to ¹⁴C-labelled model compounds, dissolved either in organic solvents or incorporated into unilamellar lecithin liposomes. Bromo-, or chloro-benzenes, decabromodiphenylether (DBP), and dichlorodiphenyl ethylene (DDE) were tested in rather high concentration of 20 μM. Cellular toxicity was low. Compound levels were related to protein, DNA, and triglyceride contents. Cellular uptake was fast and dependent on physico-chemical properties of the compounds (lipophilicity, molecular size), formulation, and cell type. Mono-halogenated benzenes showed low and similar uptake levels (= low accumulation compounds). DBP and DDE showed much higher cellular accumulations (= high accumulation compounds) except for DBP in 3T3 cells. Uptake from liposomal formulations was mostly higher than if compounds were dissolved in organic solvents. The extent of uptake correlated with the cellular content of triglycerides, except for DBP. Uptake competition between different cell types was studied in a sectorial multi-cell culture model. For low accumulation compounds negligible differences were found among C6 cells and fibroblasts. Uptake of DDE was slightly and that of DBP highly increased in fibroblasts. Well-defined cell culture systems, especially the sectorial model, are appropriate to screen for bioaccumulation and cytotoxicity of (unknown) chemical entities in vitro.     

Polychlorinated Biphenyls (PCBs) in Mussels along the Chilean Coast

- DOI: http://dx.doi.org/10.1065/espr2006.01.011 Goal, Scope and Background Chile signed the Stockholm Convention, which establishes measures to reduce or eliminate Persistent Organic Pollutants (POPs) release into the environment, including the prohibition of their use and reduction of secondary products release, as well as management related with waste treatment. Among POPs, PCBs are a family of 209 compounds that differ in chlorine level and position. These substances present a wide variability in their physicochemical properties such as vapor pressure, water solubility and partition coefficients that determine their behavior and mobility within the different environmental compartments. In Chile, as in other countries, the use of these compounds were and continue to occur in diverse industrial applications such as dielectric fluid in transformers and condensers, with a use in Chile of approximately 550,000 L. A sampling of bivalves was performed during the years 2000-2002 in order to obtain information on the spatial distribution of the PCB levels for the length of the long Chilean coast (180–540 South latitude, 4,200 km), contributing in this way to a better understanding of the PCB trend and eventual fractionation along latitudinal gradients in Chile, using as the bivalve Perumytilus purpuratus ('Chorito Maico') bioindicator. Methods The marine bivalves Perumytilus purpuratus were collected in 16 localities in northern and southern Chile. All samples were lyophilized, and PCBs (51 congeners) were extracted in a Soxhlet system (24 h) with n-hexane. Samples were cleaned in florisil and analyzed by GC-ECD. Blanks, certified reference materials and standards were processed along with the samples. Results and Discussion The results obtained for P. purpuratus indicate a congeneric distribution profile associated to a latitudinal gradient, and the statistical analysis of the congeneric composition of the PCBs indicated five groups in relation to the molecular weight (number of chlorines), where the lighter congeners were observed in areas corresponding to high latitudes with total PCB values of 298 ng/g dry weight. Conclusion P. purpuratus turns out to be a good bioindicator of PCB levels in the coastal areas of Chile due to its wide distribution. The highest concentrations and the more volatile congeners were found in southern Chile, which could be the result of processes of long-range transport or illegal discharge occurring in such remote areas. These results confirm previous data from the International Mussel Watch project ten years ago. Recommendation and Outlook Future studies are needed to confirm our findings utilizing another environmental matrix such as soil/sediments and air samples.     

臭氧多相催化氧化处理微污染水中试研究

通过中试系统初步比较了非均相催化剂催化臭氧化与传统中间臭氧化在饮用水深度处理中的净化效能.结果表明,对有机物污染宏观指标CODMn、TOC的控制,催化臭氧化具有明显优势,降低了后续处理工艺的有机物负荷;催化臭氧化与中间臭氧化对UV254的去除率相当;催化剂能够强化臭氧氧化,使其进一步去除水中持久性有毒有害有机物,并且显著地提高了臭氧氧化氨氮生成硝酸盐氮的能力,催化剂也强化了臭氧的传质与利用.     

Research on Energy Consumption Evaluation Combined with Endogenous Pollutants of China Based on Entropy-Topsis

Abstract

The traditional evaluation of energy consumption mostly introduces pollutants as a negative economic output into evaluating model, ignoring the configuration relationship among the energy input, pollutants as well as economic output. This paper considers the overall process of energy consumption and constructs an evaluation indication system of energy consumption level combined with endogenous pollutants based on entropytopsis method, then makes empirical research. The results show that China’s energy consumption level presents a fluctuant rise in the premise of emission. Energy consumption level depends on the relationship among energy input, pollutants and economic output. The raise of energy consumption level should not increase economic output and reduce pollutant emission at the expense of environment. Finally, the whole paper puts forward the countermeasures to improve the overall level of energy consumption.