MMT对GDI、PFI汽油机微粒排放的影响

为研究MMT对GDI、PFI汽油机微粒排放数量浓度以及质量浓度的影响,利用DMS500快速型微粒光谱仪,对一台增压缸内直喷(GDI)汽油机和一台自然吸气式气道喷射(PFI)汽油机燃用基础油以及在基础油中添加有机锰(MMT)的燃油的微粒排放特性进行了试验研究.结果表明:MMT的添加均会增加GDI、PFI汽油机的微粒排放,燃用不同含Mn量的燃油,各负荷下GDI汽油机的微粒数量浓度均明显高于PFI汽油机.中小负荷下GDI、PFI汽油机微粒排放数量浓度以及质量浓度均随着Mn含量的增加而上升.大负荷下,PFI汽油机微粒数量浓度随着Mn含量的增加而上升,但GDI汽油机则是在燃用不含Mn的燃油时微粒数量浓度最低,而后随着燃油中Mn含量的增加,超细微粒数量浓度的峰值反而逐步降低.GDI、PFI汽油机核模态与积聚模态微粒数量变化的规律相似.     

固体装药头部人工脱粘层应力应变仿真分析

目的研究固体发动机药柱头部人工脱粘层在50,20,-40℃等3种温度下的应力应变。方法基于线性粘弹性有限元方法,利用ABAQUS分析软件对药柱应力应变进行仿真。结果得到了人工脱粘层在3种温度条件下的Mises和最大主应力应变云图,及Ⅰ,Ⅱ界面轴向、周向和径向的应力应变对比曲线。结论最大应力应变出现在人工脱粘层根部,应力与环境温度的变化成线性关系,温度变化对Ⅰ界面上脱粘层轴向应变、Ⅱ界面上径向应变影响最大。     

DME简化反应模型及其在HCCI燃烧分析中的应用研究

提出了一个可应用于HCCI发动机工作过程研究的DME化学反应动力学简化模型,该模型由28种组分、38个基元反应组成,包括3个子模型,即低温反应和负温度系数区子模型、高温裂解和高温氧化子模型以及甲酸生成过程子模型.通过算例对比分析,该DME简化模型能正确揭示DME燃烧过程主要生成物组分的变化规律,能准确计算DME燃烧过程低温和高温阶段的放热特征时刻,其计算结果与详细机理计算结果吻合.相对于详细机理,简化模型节省了计算时间,为实现化学反应动力学与CFD多维模型耦合的燃烧计算提供了一个可行而有效的途径.     

Emission and Performance Characteristics of a 2 Litre Toyota Diesel Van Operating on Esterified Waste Cooking Oil and Mineral Diesel Fuel

Exhaust emission and performance characteristics were evaluated in a Toyota van, powered by a 21 indirect injection (IDI) naturally aspirated diesel engine, operating on vegetable based waste cooking oil methyl ester (WCOME).Tests were performed on a chassis dynamometer and the data were compared with previous results conducted on the same vehicle using mineral diesel fuel. The data obtained includes smoke opacity, carbon monoxide (CO), carbon dioxide (CO₂), oxygen (O₂), nitrogen dioxide (NO₂), nitric oxide (NO), sulfur dioxide (SO₂) and brake power. Engine lubricating oil samples were also taken. Results from this study indicated a difference of approximately 9% in brake power between the two fuels. WCOME developed a significant lower smoke opacity level and reduced CO, CO₂, SO₂ emissions. However, O₂, NO₂ and NO levels were higher with the vegetable oil based fuel. Power values were comparable for both fuels. Lubricating oil analysis gave little change of viscosity and wear metal concentrations after 2887km were: Silicon 35ppm, Chromium 3.3ppm, Iron 33.8ppm, Copper 14.1ppm and lead 78.6ppm.     

La1-x Cex Cuy Mn1-yO3／HZSM-5催化剂低温去除柴油机碳烟和NOx

为实现对柴油机碳烟和NOx的低温同步去除，采用柠檬酸络合法制备分子筛负载钙钛矿型金属复合氧化物催化剂，应用x衍射分析仪（XRD）和电镜扫描仪（SEM）对催化剂性能进行表征，并在微型固定床反应器中对催化剂低温去除碳烟和NOx进行活性评价。利用程序升温反应（TPR）技术，进行催化剂活性评价、柴油机负荷和排放等特性实验。结果表明，A位用适量Ce部分取代La，B位用适量cu部分取代Mn，可使碳颗粒燃烧温度降低，CO2选择性好，NOx转化率升高。La0.4 Ce0.6 Cu0.2 Mn0.8O3／HZSM-5催化剂的最大NOx转化率为81．0％，Ti、Tm和Tf分别为250、350和475℃，表明该催化剂具有较好的催化活性，能在低温条件下去除碳烟和NOx。     

Performance Enhancement of a Beta Type Rhombic Drive Stirling engine

ABSTRACT

Stirling engines maintain attraction because of their high energy conversion efficiencies. In this study, experimental comparison of a beta-type Stirling engine for two different rhombic-drive mechanisms was presented. In one of the rhombic mechanisms, spur gears were used and the gear shaft was supported in bearings from one side. In the other mechanism, two helical gears were placed on crankshafts and the crankshafts were supported in bearings from both sides. Rhombus lengths of the mechanisms were determined as 66 mm and 80 mm to provide same constant compression ratio of 2.5 for both configurations. Both mechanisms were used in the same beta-type Stirling engine having same cylinder, piston and displacer dimensions. Performance parameters of the engines were evaluated at different helium charge pressures (2–4 bar) and hot-end temperatures (400–600°C). The hot-end of the displacer cylinder was heated by a liquefied petroleum gas (LPG) burner. The engine power increased by 132%, friction losses and gear noses were reduced by supporting the rhombic-drive mechanism from both side and using helical gears. The maximum output torque and power of the engine were obtained as 13.14 Nm at 428 rpm engine speed and 663 W at 800 rpm engine speed, respectively, at 600°C hot-end temperature and 4 bar charge pressure.     

柴油车烟度计维修二例

环境监测仪器由于受环境条件等因素的影响 ,经常会出现各种故障 ,文章对柴油车烟度计检测时表头指针无指示故障进行了系统分析 ,并介绍了维修方法和步骤     

柴油机排放颗粒物组成分析

采用过滤分离、超声洗脱和气质联用等技术,实验测定了柴油机尾气中碳烟颗粒物的质量含量、可溶性有机组分在颗粒物中的质量分数和可溶性有机组分的化学组成。在实验条件下,柴油机尾气中碳烟颗粒物的质量含量为32·6~143·6mg/m3。可溶性有机组分在颗粒物中的质量分数为18·5%~89·4%。可溶性有机组分中检测出有机物100多种,已确定化学结构的有机物73种,其中直链和支链烷烃含量占81·22%,芳烃类化合物17·94%。     

铝质发动机罩的行人碰撞保护研究

应用HyperMesh建立发动机罩和行人头部的有限元模型,利用LS-DYNA有限元分析软件研究人的头部与钢质、铝质发动机罩相撞时的动态响应问题,并经试验验证。对头模撞击铝质发动机罩与钢质发动机罩作了比较,得出铝质发动机罩对行人头部具有更好保护效果的结论。对铝质发动机罩内、外板的厚度进行改进设计,得到综合轻量化、刚度及安全性3方面的要求都比较好的设计方案。最后对铝质发动机罩的内板结构进行拓扑优化设计,得到了在保证刚度的前提下减重效果最好、具有优异的行人碰撞保护性能的铝质发动机罩结构。     

浅谈大功率柴油机余热发电

介绍了中山柴油机发电厂余热发电技改项目,并分析论述了利用大功率柴油机排烟余热发电的优点.在油价高企的背景下,实施余热发电是节能环保的有效措施之一.