天津市夏季蜂窝状溶蚀器涂层溶液浓度确定的实验研究

于2013年7月1日～8月31日,在天津市南开大学理化楼楼顶,采用蜂窝状溶蚀器进行了溶蚀器涂层溶液最适浓度的探究实验.结果表明,在天津夏季,蜂窝状溶蚀器的碳酸钠涂层溶液最适浓度为3%,柠檬酸涂层溶液最适浓度为6%.含有溶蚀器系统的颗粒物采样法与传统采样法对比发现,含蜂窝状溶蚀器的采样系统所得到的PM2.5样品浓度有86%低于传统方法所得到的PM2.5样品浓度,其原因主要为1酸/碱性气体被去除,使其无法与富集在采样膜上的颗粒物发生反应,也无法吸附到颗粒物上;2溶蚀器系统采样过程中,部分颗粒物被捕集到溶蚀器上;3酸/碱性气体被去除,导致气-粒平衡被打破,部分颗粒物组分向气态转化.     

烟气脱硫溶液中硫酸根的去除

分别采用石灰乳化学沉淀法和低温结晶法去除烟气脱硫溶液中的SO42-。实验结果表明：在室温、CaO溶液质量分数25%的条件下，石灰乳化学沉淀法对SO42-的去除率仅为59.51%，且向溶液中引入了Ca2+，产生的硫酸钙固体废物难以再生利用；采用低温结晶法处理烟气脱硫溶液，在结晶温度7 ℃、结晶时间3 h、NaOH加入量34.8 g/L的条件下，SO42-的去除率为82.04%、滤液中的ρ（Na+）为3.88 g/L。在现场工业应用试验中，采用低温结晶法去除烟气脱硫溶液中的SO42-，平均SO42-的去除率可达70.00%以上，滤液中的ρ（Na+）小于15.00 g/L。该法可有效抑制烟气脱硫溶液中SO42-含量的增加。     

节能技改在提升安全水平优化产品结构上的实际应用

引言 某企业6．5万吨／年氢氧化钾（纯KOH，包含固碱和液碱）项目由盐水精制工段、盐水电解工段、及固碱工段等部分组成，本次节能技术革新与安全设施改造主要是针对固碱工段的固碱工艺方法。改造的目的一是利用导热油炉给流程图见图1。     

硝铵共浆溶液热安全性研究

为防止硝铵共浆溶液在配制、储存、运输和生产复合肥过程中发生爆炸事故,利用自制实验装置对硝铵共浆溶液的热安全性进行了实验研究.结果表明,硝铵共浆溶液低于纯硝酸铵水溶液的临界爆炸温度,具有很大的危险性；硝酸铵的浓度对硝铵共浆溶液的临界爆炸温度的影响很大,硝酸铵浓度越高,其临界爆炸温度就越低,也越易爆炸；氯离子有促进硝铵共浆溶液爆炸的作用；油脂会降低硝铵共浆溶液的热稳定性,降低其临界爆炸温度.研究结果对相关化肥企业的安全生产有指导意义.     

含稀醋酸废水中醋酸的回收方法

该发明涉及含稀醋酸废水中醋酸的回收方法，其特点是：先用电渗析法对含稀醋酸废水进行处理，获得质量浓度小于1000mg／L的醋酸极稀溶液，然后用阴离子交换树脂吸附法进一步脱除回收剩余的极稀溶液中的醋酸，使最后排除的废水中醋酸的质量浓度小于50mg／L。该方法将电渗析法与吸附法相结合，既克服了醋酸极稀溶液电导率低、电渗析过程电耗大的缺点，     

煤矿矿井水中SO2-4的去除方法研究

制备了高效SO2-4吸附剂,用其对某煤矿矿井水进行了试验,对影响吸附剂吸附效率的各因素进行了研究,结果表明:吸附剂用量1.0 g/L时,去除率达到最高,为93.5%.溶液在酸性范围内吸附剂对SO2-4去除率明显大于碱性范围.随着SO2-4浓度的增加,吸附剂的去除率逐渐降低.试验水温选择为25℃,最佳吸附时间为40 min,最佳pH为7.0.     

粘土吸附水中氟离子的研究

研究了粘土和明矾去除饮用水中氟离子的机理,探讨了pH值、溶液温度、氟离子浓度和吸附时间对粘土吸附饮用水中氟离子的影响.结果表明,粘土对饮用水中氟离子具有较好的吸附效果,是较为理想的饮水除氟材料.     

荷电超滤膜对天然有机物去除及膜污染行为的影响

以Aldrich 腐殖酸溶液为水样,研究比较了溶液环境(pH值、离子强度和钙离子)对荷电改性再生纤维素超滤膜和传统中性未改性再生纤维素超滤膜过滤过程的影响.结果表明, ①pH值主要通过质子化作用影响荷电膜以及腐殖酸分子的荷电量,进而影响荷电超滤过程.溶液pH值从7.5下降到3.5时,荷电超滤膜对腐殖酸的截留率从92%减少到79%,超滤4 h时,膜通量下降从26%增加到36%.②离子强度的改变是通过影响腐殖酸分子的物化性质和静电屏蔽作用来影响超滤过程的.当溶液离子强度为0、 3和100 mmol/L时,初始截留率依次降低,分别为92%、 87%和48%,超滤4 h时,荷电超滤膜的通量下降依次增加,分别为26%、 35%和63%.③Ca2+浓度的影响,需要综合考虑静电屏蔽作用、Ca2+的架桥作用以及滤饼层的压实性等各方面的影响.④pH值、离子强度和钙离子对中性超滤膜过滤行为的影响趋势与荷电超滤膜相似,但其影响程度有着较大的差别.研究结果对荷电超滤膜技术在实际应用中选择合适环境条件提供了参考.     

Removal of heavy metal ions from aqueous solution using red loess as an adsorbent

The adsorption behaviors of heavy metals onto novel low-cost adsorbent, red loess, were investigated. Red loess was characterized by X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectra. The results indicated that red loess mainly consisted of silicate, ferric and aluminum oxides. Solution pH, adsorbent dosage, initial metal concentration, contact time and temperature significantly influenced the efficiency of heavy metals removal. The adsorption reached equilibrium at 4 hr, and the experimental equilibrium data were fitted to Langmuir monolayer adsorption model. The adsorption of Cu(II) and Zn(II) onto red loess was endothermic, while the adsorption of Pb(II) was exothermic. The maximum adsorption capacities of red loess for Pb(II), Cu(II) and Zn(II) were estimated to be 113.6, 34.2 and 17.5 mg/g, respectively at 25°C and pH 6. The maximum removal efficiencies were 100% for Pb(II) at pH 7, 100% for Cu(II) at pH 8, and 80% for Zn(II) at pH 8. The used adsorbents were readily regenerated using dilute HC1 solution, indicating that red loess has a high reusability. All the above results demonstrated that red loess could be used as a possible alternative low-cost adsorbent for the removal of heavy metals from aqueous solution.     

Chemical cleaning of fouled PVC membrane during ultrafiltration of algal-rich water

Cleaning of hollow-fibre polyvinyl chloride (PVC) membrane with di erent chemical reagents after ultrafiltration of algal-rich water was investigated. Among the tested cleaning reagents (NaOH, HCl, EDTA, and NaClO), 100 mg/L NaClO exhibited the best performance (88.4% 1.1%) in removing the irreversible fouling resistance. This might be attributed to the fact that NaClO could eliminate almost all the major foulants such as carbohydrate-like and protein-like materials on the membrane surface, as confirmed by Fourier transform infrared spectroscopy analysis. However, negligible irreversible resistance (1.5% 1.0%) was obtained when the membrane was cleaning by 500 mg/L NaOH for 1.0 hr, although the NaOH solution could also desorb a portion of the major foulants from the fouled PVC membrane. Scanning electronic microscopy and atomic force microscopy analyses demonstrated that 500 mg/L NaOH could change the structure of the residual foulants on the membrane, making them more tightly attached to the membrane surface. This phenomenon might be responsible for the negligible membrane permeability restoration after NaOH cleaning. On the other hand, the microscopic analyses reflected that NaClO could e ectively remove the foulants accumulated on the membrane surface.