Statistical apportionment and risk assessment of selected metals in sediments from Rawal Lake (Pakistan)

The present study was carried out in order to evaluate the statistical apportionment and risk assessment of selected metals (Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Pb, Sr, and Zn) in freshly deposited sediments in Rawal Lake, Pakistan. Composite sediment samples were collected, oven-dried, grounded, homogenized, and processed to assess the water-soluble and acid extractable concentrations of the metals in the water extract and acid extract of the sediments using flame atomic absorption spectrophotometer. Statistical methods were used to identify the possible sources of the metals. Sediment quality guidelines and potential acute toxicity were used to evaluate the ecotoxicological sense of selected metals. Non-carcinogenic health risk assessment was also carried out to determine the potential adverse health risks to the inhabitants. Relatively higher concentration was noted for Ca, Fe, Mg, Na, K, Mn, and Sr in the sediment samples. Principal component analysis and cluster analysis revealed anthropogenic contributions of Cd, Pb, Cr, Mn, Fe, and Li in the sediments. Enrichment factors of the metals in sediments showed severe to moderate enrichment of Cd, Pb, Ca, Fe, Li, Mn, and Sr. Geoaccumulation indices and contamination factors evidenced significant contamination by Cd and Pb, although, on the whole, low degree of contamination was noted. The levels of some metals exceeded the sediment quality guidelines, which revealed frequently adverse biological effects to the dwelling biota in the aquatic ecosystem. The sediments were found to be significantly contaminated by Cd, Pb, Cr, Mn, Fe, and Li.     

Optical and Chemical Methods of Metal Ash Analysis and Tin Recovery

‘Metal ash’ presents a waste disposal problem in most of the developing countries as the industries employ obsolete technologies. In this paper we describe analysis of tin ash, zinc ash and aluminium ash by means of optical methods, such as X-ray diffraction (XRD), inductively coupled plasma mass spectrometry (ICP-MS), electron probe micro analysis (EPMA), scanning electron microscopy (SEM) and chemical methods. The results of tin ash obtained by XRD method matched well with the cassiterite, a naturally occurring mineral of tin. ICP-MS studies reveal the presence of a large number of tracer metals, which may cause pollution by tertiary dispersion and this aspect is discussed. Conversely, the data generated by chemical methods are limited. However, the methods are simple and cost-effective. Then, they can easily be adopted by low-budget industries. Simple and cost-effective process to recover tin from tin ash is described. It is based on heating tin ash with sodium cyanide to about 900°C to separate tin component from the metal ash. The process recovers good quality tin and offers a very high yield. The process can be scaled up to small pilot plant.     

An investigation of ergonomics analysis tools used in industry in the identification of work-related musculoskeletal disorders.

Web-based surveys were sent to Canadian certified ergonomists, Joint Health and Safety Committees (JHSCs) and health and safety certification trainers to understand better which ergonomics analysis tools were used in industry and help JHSCs obtain the necessary training required to reduce work-related musculoskeletal disorders (WMSDs). The results showed that most of the certified ergonomists used the Snook/Mital tables, the National Institute of Occupational Safety and Health (NIOSH) equation and rapid upper limb assessment (RULA) /rapid entire body assessment (REBA). The most frequently used methods by JHSCs to identify ergonomics risk were injury reports and worker complaints. The surveys for the health and safety certification trainers revealed that most curricula did not include ergonomics analysis tools. There appears to be a gap between what is recommended by certified ergonomists for JHSC, what is taught in training and what is used by JHSCs for ergonomics risk analysis. A better understanding, modifications in training curricula and education of JHSCs are needed to help reduce WMSDs.     

The potential of cost-effective coconut husk for the removal of toxic metal ions for environmental protection

Coconut (Cocos nucifera) husk, an agricultural waste, has been thoroughly investigated for the removal of toxic Cd(II), Cr(III) and Hg(II) ions from aqueous media. The parameters like nature and composition of electrolyte, concentration of toxic ions, dosage of coconut husk, and equilibration time between the two phases were optimized for their maximum accumulation onto the solid surface. The effect of common ions on the uptake of metal ions has been monitored under optimal conditions. The variation of retention of each metal ion with temperature was used to compute the thermodynamic quantities DeltaH, DeltaS and DeltaG. The values 18.1+/-0.6 kJmol(-1), 74+/-2 Jmol(-1)K(-1), and -3.8+/-0.04 kJmol(-1) at 298 K; 10.8+/-0.8 kJmol(-1), 48.8+/-2.7 Jmol(-1)K(-1), and -4.6+/-0.3 kJmol(-1) at 298 K; and -37.4+/-2k Jmol(-1), 105+/-7 Jmol(-1)K(-1) and -2.58+/-0.5 kJmol(-1) at 298 K were obtained for Cd(II), Cr(III) and Hg(II) ions, respectively. The sorption data were analysed by applying different sorption isotherms. The sorption capacity and energy were evaluated for each metal ion. The values of the Freundlich constants 1/n and C(m) were 0.92+/-0.04 and 52.6+/-22.2 mmolg(-1); 0.85+/-0.05 and 56.0+/-0.03 mmolg(-1); and 0.88+/-0.03 and 6.84+/-0.45 mmolg(-1) for Cd(II) Cr(III) and Hg(II) ions, respectively. Similarly, the Dubinin-Radushkevich (D-R) constants beta, X(m,) and E were evaluated for the three metal ions. To check the selectivity of the sorbent, sorption of a number of elements was measured under similar conditions. Separation of Zn(II) from Cd(II); Cr(III) from I(I), Zr(IV), Se(IV), and Hg(II) from Se(IV) and Zn(II) can be achieved using this sorbent. This cheap material has potential applications in analytical chemistry, water decontamination, industrial effluent treatment and in pollution abatement.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Cattle egrets as a biosentinels of persistent organic pollutants exposure

We investigated selected chlorinated pollutants (β-HCH, γ-HCH, DDDs, DDEs, o,p′-DDT, p,p′-DDT, heptachlor, aldrin, dieldrin, and endrin) in the Lahore and the Sialkot districts of Pakistan, using eggs of cattle egret (Bubulcus ibis) collected during May and June 2007. The pollutant with highest level and frequency was ΣDDT, followed by β-HCH, γ-HCH, heptachlor, aldrin, dieldrin, and endrin in descending order. The concentration(s) were significantly higher in Sialkot heronry for all the pollutants (except p,p′-DDT) than in Lahore. The values for DDTs, β-HCH, γ-HCH, and heptachlor were significantly higher (p < 0.05) in the egg(s) than in sediment(s) and in the chicks’ diet, due to biomagnification. Among DDTs analogues, p,p′-DDD was the major contaminant with >60 % of total DDT burden, reflecting the widespread aged as well as recent use of DDT as well as anaerobic degradation (DDD/DDE > 1 in many cases) in the nearby paddy soils. In few samples, p,p′-DDT/(DDD + DDE) > 0.5 suggested the recent emission patterns from surrounding contaminated areas of demolished DDT units and obsolete pesticide stores. The higher levels of HCHs (i.e., β-HCH) in the samples collected from Sialkot indicate exposure from long-term agricultural use. Overall, concentrations of all studied POPs were less than the threshold levels known to affect reproduction. Nevertheless, total DDTs and/or HCHs burdens in some eggs contained concentrations of greater than what would educe adverse effects on birds. This is among few studies on OCPs exposure to avian species, which provide the evidence of Pakistan’s contribution toward the Global POPs emission.     

Application of Zr(IV) tungstate for removal of metal ions from aqueous solutions

A heteropolyacid Zr(IV) tungstate-based cation exchanger has been synthesized. An amorphous sample, prepared at pH 1.2 and having a Na⁺ ion exchange capacity of 0.92?meq?g^?1, was selected for further studies. Its physicochemical properties were determined using Fourier transform infrared spectrometer, X-ray diffraction, thermogravimetric, and scanning electron studies. To understand the cation exchange behavior of the material, distribution coefficients (K _d) for metal ions in various solvent systems were determined. Some important binary separations of metal ions, namely Mg²⁺–Bi³⁺, Cd²⁺–Bi³⁺, Fe³⁺–Bi³⁺, Th⁴⁺–Bi³⁺, and Fe³⁺–Zn²⁺, were achieved on such columns. The practical utility of these separations was demonstrated by separating Fe³⁺ and Zn²⁺ ions quantitatively in commercial pharmaceutical formulation. The cation exchanger has been successfully applied also for the treatment of industrial wastewater and a synthetic mixture. All the results suggests that Zr(IV) tungstate has excellent potential for the removal of metals from aqueous systems using packed columns of this material.     

Sol-gel immobilisation of methyl parathion degrading bacteria isolated from agricultural areas of Pakistan

The following areas are discussed in this paper: immobilisation of bacterial consortium in sol-gel; methyl parathion degradation and bioremediation applications; evaluation of indigenous bacterial isolates of contaminated soils. Bacterial strains were isolated from agricultural areas of Pakistan which were contaminated with methyl parathion. A bacterial consortium of seven (out of 64) Enterobacteriaceae isolates including Citrobacter, Enterobacter and Proteus vulgaris capable of degrading methyl parathion (enzyme activity ranging 410–675 mU mL^?1 for individual isolates and 982 mU/mL for consortium) was selected and subsequently immobilised in tetraethyl orthosilicate (TEOS) and sodium-silicate-based sol-gel matrices. Cell viability of suspended and immobilised bacterial consortium was monitored using a minimal salt medium supplemented with methyl parathion. The results indicate that sol-gel immobilisation can be helpful to increase the shelf life of methyl parathion degrading bacterial strains along with preservation of biological activity for bioremediation applications in field.