Safe speed limits for a safe system: The relationship between speed limit and fatal crash rate for different crash types

Objective: The objective of this article is to provide empirical evidence for safe speed limits that will meet the objectives of the Safe System by examining the relationship between speed limit and injury severity for different crash types, using police-reported crash data.

Method: Police-reported crashes from 2 Australian jurisdictions were used to calculate a fatal crash rate by speed limit and crash type. Example safe speed limits were defined using threshold risk levels.

Results: A positive exponential relationship between speed limit and fatality rate was found. For an example fatality rate threshold of 1 in 100 crashes it was found that safe speed limits are 40 km/h for pedestrian crashes; 50 km/h for head-on crashes; 60 km/h for hit fixed object crashes; 80 km/h for right angle, right turn, and left road/rollover crashes; and 110 km/h or more for rear-end crashes.

Conclusions: The positive exponential relationship between speed limit and fatal crash rate is consistent with prior research into speed and crash risk. The results indicate that speed zones of 100 km/h or more only meet the objectives of the Safe System, with regard to fatal crashes, where all crash types except rear-end crashes are exceedingly rare, such as on a high standard restricted access highway with a safe roadside design.     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Analytical mapping of research on disaster management,types and role of ICT during 2011–2018

Catastrophic disasters like earthquake and flood cause widespread destruction and financial devastation. This has brought disaster management into limelight making it a burgeoning academic research field. The remarkable rise of ICT (Information and Communication Technology) has instigated the scientific world to incorporate these technologies in disaster management. This study presents scientometric analysis to identify the status quo of research on the management of various disasters and role of ICT in it. This paper uses bibliographic data retrieved from Scopus for the observation period from 2011 to 2018. We provide extensive insights into growth of publications, citation pattern and their connectedness with other subject disciplines. Furthermore, we identify most productive and influential countries, institutes and journals. Our study analyses co-occurrence of keywords using Visualization of Similarities (VOS) Viewer. This structured overview will enhance the understanding of this field leading to more focussed and purposeful research.     

Analysis and optimization on the biodegradable plate making process parameters using RSM-based Box–Behnken Design method

Journal of Material Cycles and Waste Management - The present research work focused on fabricating Biodegradable Plate (BD plate) composed of rice husk ash, bagasse and corn starch which is...     

Challenges for modelling and integrating environmental performances in concept design: the case of an automotive component lightweighting

The objective of this paper is to discuss the main barriers for modelling and integrating the environmental performances in the automotive concept design. Incorporating environmental assessment in the early design phase of a vehicle component is known as an important challenge that car makers need to face in order to develop more sustainable design solutions; in this regard, the Life Cycle Assessment is the most widespread methodology for the environmental assessment and comparison of alternatives. The present work illustrates the combination of such methodology with the traditional design procedure at two different levels of the component design phase, material choice and concept design. In particular, the potential benefits originated by a lightweight solution for the automotive component Throttle Body are evaluated by considering environmental and technical implications at the same level. The case study shows that a multi-disciplinary approach for design effectively allows the integration of the environmental issue in the company’s established procedures. However, interpretation of results is still a challenging aspect due to the inevitable contradicting elements which should not discourage to develop comprehensive sustainability assessment within the early design stage.     

The Response of Hydrophytes to Environmental Pollution with Heavy Metals

The effects of Cu²⁺, Cd²⁺, and Ni²⁺ at low and high concentrations (0.025 and 0.25 mg/ml) on the accumulation capacity, the state of the pigment complex, and photosynthesis rate have been studied in model experiments with three floating hydrophytes (Hydrocharis morsus-ranae L., Lemna gibba L., and Potamogeton natans L.) and four submerged hydrophytes (Elodea canadensis Michx., Lemna trisulka L., Ceratophyllum demersum L., and Potamogeton lucens L.). Copper and cadmium are especially toxic at the concentrations studied. The effect of Cu²⁺ was the strongest in hydatophytes, and the effect of Cd²⁺, in pleustophytes. It is hypothesized that the differences between hydrophytes with respect to accumulation of metals and decrease in photosynthesis rate may cause predominant elimination of submerged species. Therefore, changes in the species structure of hydrophyte communities may be expected in waters polluted with metals.     

Experience in quantitative analysis of floristic structure and diversity in Samarskaya Luka

Quantitative methods have been applied to the study of floristic structure and diversity in Samarskaya Luka. The results show that Samarskaya Luka is a floristically heterogeneous area in which six elementary floras can be distinguished. This area has been assessed as a floristically autonomous formation, and its floristic representativeness was estimated.     

Estimating sampling frequency in pollen exposure assessment over time

A time series model was fitted to the pollen concentration data collected in the Greater Cincinnati area for the Cincinnati Childhood Allergy and Air Pollution Study (CCAAPS). A traditional time series analysis and temporal variogram approach were applied to the regularly spaced databases (collected in 2003) and irregularly spaced ones (collected in 2002), respectively. The aim was to evaluate the effect of the sampling frequency on the sampling precision in terms of inverse of standard error of the overall level of mean value across time. The presence of high autocorrelation in the data was confirmed and indicated some degree of temporal redundancy in the pollen concentration data. Therefore, it was suggested that sampling frequency could be reduced from once a day to once every several days without a major loss of sampling precision of the overall mean over time. Considering the trade-offs between sampling frequency and the possibility of sampling bias increasing with larger sampling interval, we recommend that the sampling interval should take values from 3 to 5 days for the pollen monitoring program, if the goal is to track the long-term average.