海藻酸钠包埋活性炭与细菌的条件优化及其对Pb~(2+)的吸附特征研究

利用海藻酸钠固定化包埋活性炭与多黏类芽孢杆菌GA1,通过正交试验研究海藻酸钠溶液浓度、包炭量及包菌量吸附Pb2+的最佳配比,并研究了这种新型的固定化小球对Pb2+的吸附特征.结果表明,固定化活性炭与多黏类芽孢杆菌GA1小球最佳制备条件为海藻酸钠质量分数2.5%、包炭量1:20和包菌量1:2,在该制备条件下吸附率达到93.74%.固定化小球的最佳吸附条件为pH5、温度30℃和Pb2+初始浓度300mg·L-1,活性炭与GA1经固定后对pH、温度和Pb2+初始浓度适应范围扩大.吸附平衡曲线表明,对Pb2+的吸附在30min内是一个快速的过程,在2h时基本趋于平衡,且平衡曲线能较好地用Langmuir模型和Freundlich模型来描述,其吸附过程主要为单分子层吸附,最大单分子层吸附量为370.37mg·g-1.解吸结果表明固定化小球能有效地循环利用.     

PCR-DGGE技术分析倒置A~2/O工艺处理染织废水中的微生物区系

基于16S rDNA的PCR-DGGE(polymerase chain reaction-denaturing gradient gel electrophoresis)技术研究了倒置A2/O(anoxic-anaerobic-aerobic)工艺处理染织废水过程中的微生物群落结构.从兼氧、厌氧和好氧区共取6个不同处理阶段的样品,测量了不同处理阶段样品的COD、pH、NH4+-N、H2S、总磷(TP)、污泥含量(TS)、色度及其脱除率,并分析了这些指标的变化规律.结果显示,COD在处理后期降到了145mg·L-1,NH4+-N的脱除率可达到85%,硫化氢的去除率达到了90%以上,磷的脱除率可达80%以上,TS处于逐渐升高的趋势,色度的脱除率达到65%.DGGE图谱显示,好氧处理阶段的微生物多样性明显比兼氧处理和厌氧处理的阶段的要丰富.     

纳米复合聚硅酸铝的颗粒粒度效应:Al_(13)与氧化硅的相互作用及其混凝特征

为了研究纳米复合聚硅酸铝(PASC)混凝剂的颗粒粒度效应,以实验室提纯的Al13溶液和活化水玻璃为原料,制备一系列不同粒度分布的PASC.以Al-Ferron法测定的铝水解形态表明,在该混凝剂中,Al13作为混凝优势形态具有较好的稳定性.氧化硅聚集度的测定和粒度分析结果表明,活化硅酸的加入能显著提高混凝剂的平均粒度,同时,Si/Al比(物质的量比)是影响平均粒度的主要因素.在活化硅酸不过量的前提下,Si/Al比和混凝剂的平均粒度呈正相关.混凝实验结果表明,在保证电中和能力的前提下,混凝剂的颗粒粒度越大,混凝剂的除浊能力越强.     

基于唐南渗析原理阳离子交换膜对Cu~(2+)、Mn~(2+)、Zn~(2+)去除能力的研究

基于唐南渗析原理,采用阳离子交换膜去除原水中Cu2+、Mn2+、Zn2+等重金属离子,研究影响阳离子交换膜去除各重金属离子能力大小的机制以及2种重金属离子共存时互相干扰的机制.结果表明,阳离子交换膜可有效去除原水中Cu2+、Mn2+、Zn2+等重金属离子,去除率为75%～85%;在浓度相同下且重金属离子带相同电荷数时,其水化离子半径越小,离子扩散速度就越快,阳离子交换膜对其去除能力就越强;当重金属水化离子半径基本相同时,膜对原子序数小的重金属离子的去除能力更强;相同浓度且相同电荷数的重金属离子共存时,各离子同步被去除,但各离子之间存在干扰,越易于被离子交换的离子与其它离子共存时,其竞争能力越强,使其他离子的去除率降低越多;当待去除离子的总浓度远低于膜的交换容量时,离子共存时各离子的去除率相比离子单独存在时各离子的去除率下降幅度不大.     

亚硝酸盐积累对A~2O工艺生物除磷的影响

常温条件下,通过控制好氧区DO浓度为0.3～0.5 mg/L,同时增大系统内回流比以降低系统好氧实际水力停留时间(actual hydraulic retention time,AHRT),在处理低C/N比实际生活污水的A2O工艺中成功启动并维持了短程硝化反硝化.但随着系统出水亚硝酸盐含量的升高,系统对磷的去除效果逐渐恶化.当好氧区亚硝酸盐浓度19 mg/L时,系统出水磷浓度大于进水磷浓度,系统处于净释磷状态.通过对原水COD浓度、反应区温度、pH值、游离亚硝酸浓度(free nitrous acid,FNA)等分析,表明碳源不足及短程硝化引起的亚硝酸盐积累影响了聚磷菌厌氧释磷和好氧吸磷;尤其是好氧区较高的FNA浓度(HNO2-N 0.002～0.003 mg/L)对聚磷菌好氧吸磷的抑制是导致系统除磷效果恶化的直接原因.通过外投碳源提高原水COD浓度,提高了聚磷菌厌氧释磷合成PHA的能力;同时增强了系统的反硝化能力,降低好氧区亚硝酸盐浓度,从而降低FNA对聚磷菌好氧吸磷的抑制程度,系统的除磷性能可迅速恢复;系统对磷的去除率可达96%以上.     

A~2/O-曝气生物滤池工艺处理低C/N比生活污水脱氮除磷

以低C/N比实际生活污水为研究对象,重点考查了A2/O-曝气生物滤池生化系统的脱氮除磷特性.同时,考虑到A2/O工艺的主要功能是除磷及反硝化,而曝气生物滤池则以硝化为目的.因此,通过缩短A2/O的泥龄,可将硝化过程从A2/O中分离出去,让曝气生物滤池完成硝化,实现硝化菌和聚磷菌的分离,并解决了硝化菌和聚磷菌泥龄之间的矛盾.试验结果表明,该生化系统可实现有机物、氮和磷的同步去除.在平均C/N比为4.2,内回流比R为250%的条件下,平均进水COD、TN、TP分别为239.9、57.3和5.1mg·L-1,平均最终出水COD、TN、TP分别为34.1、13.3和0.1mg·L-1,去除率分别为85.8%、76.9%和98.3%.曝气生物滤池对氨氮几乎保持了100%的去除率.序批试验表明,反硝化聚磷菌占聚磷菌的比例为40.5%.     

纳米催化剂Pd/SnO_2的制备及催化还原硝酸盐反应的调控

采用热分解法制备了SnO2载体,并用浸渍法制备了Pd/SnO2催化剂.同时,采用X射线衍射仪(XRD)、透射电镜(TEM)、扫描电镜(SEM)及BET比表面积仪等对所制载体和催化剂材料进行了分析表征.结果表明,热分解法和浸渍法都能够获得纳米材料,SnO2及Pd/SnO2的粒径均在9～10nm左右,比表面积分别达到144.99m·2g-1和147.36m·2g-1.在以甲酸为还原剂的Pd/SnO2催化还原硝酸盐体系中,在Pd与SnO2负载比为2%～7%,反应温度为20～50℃和甲酸投加量4.0～24.0mmol·L-1的条件下,催化活性为0.70～9.48mg·min-·1g-1,且催化活性随着负载比、温度和甲酸投加量的增大而增大,随着pH的升高先升后降,最佳pH为3.反应温度升高及pH降低都能够提高Pd/SnO2的选择性.甲酸-Pd/SnO2催化还原硝酸盐体系中还原反应的调控策略为:反应温度宜控制在40～50℃内,这样可同时获得较高的催化活性和选择性,温度过高对催化活性和选择性影响很小,温度过低则会同时降低催化活性和选择性;控制pH为3时,可以获得最大的催化活性及较好的选择性,pH升高会降低Pd/SnO2的催化活性和选择性,pH降低会导致催化活性迅速降低,但对选择性影响不大;甲酸与硝酸盐的物质的量比宜大于4:1,此时可以有效地抑制pH的上升,同时获得较高的催化活性和选择性,甲酸与硝酸盐的物质的量比小于4:1时,会同时降低Pd/SnO2的催化活性和选择性.     

A comparative investigation of NdSrCu_(1-x) Co_x O_(4-δ) and Sm_(1.8) Ce_(0.2) Cu_(1-x) Co_x O_(4-δ) (x:0–0.4) for NO decomposition

A series of single-phase T-structured NdSrCu 1-x Co x O 4-δ with oxygen vacancies and T -structured Sm 1.8 Ce 0.2 Cu 1-x Co x O 4-δ (x: 0–0.4) with oxygen excess were prepared using ultrasound-assisted citric acid complexing method, and characterized by means of techniques such as thermogravimetric analysis and NO temperature-programmed desorption (NO-TPD). The catalytic activities of these materials were evaluated for the decomposition of NO. It was found that the NdSrCu 1-x Co x O 4-δ catalysts were of oxygen vacancies whereas the Sm 1.8 Ce 0.2 Cu 1-x Co x O 4-δ ones possessed excessive oxygen (i.e., over-stoichiometric oxygen); with a rise in Co doping level, the oxygen vacancy density of NdSrCu 1-x Co x O 4-δ decreased while the over-stoichiometric oxygen amount of Sm 1.8 Ce 0.2 Cu 1-x Co x O 4-δ increased. The NO-TPD results revealed that NO could be activated much easier over the oxygen-deficient perovskite-like oxides than over the oxygen-excessive perovskite-like oxides, with the NdSrCuO 3.702 catalyst showing the best efficiency in activating NO molecules. Under the conditions of 1.0% NO/helium, 2800 hr -1 , and 600–900°C, the catalytic activity of NO decomposition followed the order of NdSrCuO 3.702 NdSrCu 0.8 Co 0.2 O 3.736 NdSrCu 0.6 Co 0.4 O 3.789 Sm 1.8 Ce 0.2 Cu 0.6 Co 0.4 O 4.187 Sm 1.8 Ce 0.2 Cu 0.8 Co 0.2 O 4.104 Sm 1.8 Ce 0.2 CuO 4.045 , in concord with the sequence of decreasing oxygen vacancy or oxygen excess density. Based on the results, we concluded that the higher oxygen vacancy density and the stronger Cu 3+ /Cu 2+ redox ability of NdSrCu 1-x Co x O 4-δ account for the easier activation of NO and consequently improve the catalytic activity of NO decomposition over the catalysts.     

Selective removal of 2,4-dichlorophenoxyacetic acid from water by molecularly-imprinted amino-functionalized silica gel sorbent

A molecularly-imprinted amino-functionalized sorbent for selective removal of 2,4-dichlorophenoxyacetic acid(2,4-D) was prepared by a surface imprinting technique in combination with a sol-gel process.The 2,4-D-imprinted amino-functionalized silica sorbent was characterized by FT-IR,nitrogen adsorption and static adsorption experiments.The selectivity of the sorbent was investigated by a batch competitive binding experiment using an aqueous 2,4-D and 2,4-dichlorophenol(2,4-DCP) mixture or using an aqueous 2...     

Degradation and detoxification of microcystin-LR in drinking water by sequential use of UV and ozone

Microcystins (MCs) produced by cyanobacteria are strong hepatotoxins and classified as possible carcinogens.MCs pose a considerable threat to human health through tainted drinking and surface waters.Herein filtrated water from a waterworks in Harbin,China,was spiked with microcystin-LR (MC-LR) extracted from a toxic scum of microcystis aeruginosa,and the spiked sample waters were treated using UV irradiation with consequent ozonation process (UV/O3),compared with ozonation at a dose range commonly applied in water treatment plants,UV irradiation at 254 nm and UV irradiation combined with ozonation (UV+O3),respectively.The remaining of toxins were analyzed using high-performance liquid chromatography and also determined using a protein phosphatase type 2A inhibition assay,which was utilized to evaluate the reduction in toxicity.Results indicated that in comparison to other three processes (O3,UV,and UV+O3),UV/O 3 process could effectively decrease both the concentration and toxicity of MC-LR at 100 μg/L level after 5 min UV irradiation with consequent 5 min ozonation at 0.2 mg/L (below 1 μg/L),while 0.5 mg/L ozone dose was required for the level below 0.1 μg/L.The addition of an UV treatment step to the existing treatment train may induce significant transformation of micropollutants and breaks down the natural organic matters into moieties unfavorable for ozone decomposition,stabilizing the ozone residual.These findings suggested that sequential use of UV and ozone may be a suitable method for the removal of these potentially hazardous microcystins from drinking water.