注入式低温等离子体技术用于卷烟厂异味处理的效果研究

将注入式低温等离子体技术应用于烟厂制丝排潮和制丝除尘排放气体异味处理中,研究了注入式低温等离子体发生器参数对臭味浓度、非甲烷总烃和可检出典型有机物去除率的影响规律。结果表明:注入式低温等离子体发生器工作电压越高,注入处理烟道的氧化活性物种浓度越高,注入量越大,臭味浓度、非甲烷总烃和可检出典型有机物去除率也越高。选取合理的工作电压,臭味浓度去除率可达90%以上,非甲烷总烃去除率分别达到了83.8%(制丝排潮)和78.1%(制丝除尘)。     

Comparative study on effect of blending,thermal barrier coating (LHR) and injector nozzle geometry on biodiesel-fuelled engines

Increased petroleum prices, increased threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for internal combustion engines. Evolving suitable technology for addressing energy crisis creates a continued investigation into the search for sustainable and clean-burning renewable fuels. This work investigates suitability of different non-edible-derived biodiesels such as cotton seed oil methyl ester (COME), Honne oil methyl ester (HnOME) and Rubber seed oil methyl ester (RuOME) to four stroke, single cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel blending, thermal barrier coating (TBC) or Low Heat Rejection (LHR) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and RuOME in the modified CI engine. Blends of biodiesels with diesel were varied from 20 to 80% in steps of 20%. Two thermal barrier coatings of partially stabilized zirconium (PSZ) and aluminium oxide (Al₂O₃) were provided on the engine to make it fully adiabatic. Nozzle injectors of 3, 4 and 5 holes, with size of orifice varied from 0.2 to 0.3 mm size were selected for the study. It was concluded that B20 biodiesel blend, PSZ-coated engine and four hole nozzle injector of 0.2 mm size resulted in overall better engine performance with increased brake thermal efficiency (BTE) and reduced HC, CO, smoke emissions for the fuel combinations tested. Combustion analysis to study the effect of biodiesel blends, LHR coatings, injector nozzle geometry on the performance of the biodiesel-fuelled engine has been presented to give more insight into the behaviour of operation.     

循环流化床入口结构对流态化效果影响比较

通过实验的方法考察了三种文丘里布风装置与两种回料方式对循环流化床流态化效果的影响。实验结果表明:在喉口面积相同的条件下,七孔文丘里布风装置同四孔文丘里布风装置及一孔文丘里布风装置相比,系统压降较低,床内平均颗粒浓度大,流态化稳定;流化斜槽回料方式同气力输送回料方式相比,对流化床入口段流场的干扰较小,塔内颗粒分布均匀。     

Effects of injection timing,injector opening pressure and nozzle geometry on the performance of cottonseed oil methyl ester-fuelled diesel engine

Increasing petroleum prices, increasing threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for engines. Evolving technology and a recurring energy crisis necessitates a continuous investigation into the search for sustainable and clean-burning renewable fuels. In this paper, cottonseed oil methyl ester (COME) was used in a four-stroke, single-cylinder variable compression ratio diesel engine. Tests were carried out to study the effects of fuel injection timing, fuel injector opening pressure (IOP) and injector nozzle geometry on the performance and combustion of COME biodiesel fuel used in a compression ignition engine with a single fuel mode. Fuel injection timing varied from 19° to 27° before top dead centre (bTDC) in incremental steps of 4° bTDC; fuel IOP varied from 210 to 240 bar in incremental steps of 10 bar. Fuel nozzle injectors with three, four and five holes, each of 0.3 mm size, were selected for the study. The results suggested that with retarded injection timing of 19° bTDC, increased IOP of 230 bar and a four-hole nozzle injector of 0.3 mm size resulted in overall better engine performance with an increased brake thermal efficiency and reduced HC, CO and smoke emission levels.     

黑臭河道生物修复中3种不同增氧方式比较研究

利用叶轮式曝气机、水下式曝气机、射流式曝气机等3种不同曝气方式的曝气设备进行了黑臭河涌曝气试验。研究表明，不同增氧方式对黑臭河道水体增氧效率不同，水下式曝气机、叶轮式曝气机均可在黑臭河道下游形成一段绿色水而，水车式曝气机下游变绿河段长度为15．7m，叶轮式曝气机下游变绿河段长度为6．3m，射流式曝气机不能形成明显的绿色水而。无论足河道水体增氧效果、CODcr、NH3-N去除效果，还足河道菌-藻生态系统的建口、自净能力的肩动，水下式增氧机均优于其它两种增氧机，而且存在投资少、安装维护方便、运行费用低等优点。适应于河道窄、水流缓、截污难度大的城郊中小型黑臭河道的治理。     

甲醛法在测定固定污染源排放SO2浓度中的应用

对用注射器采样甲醛法测定高浓度ＳＯ２样气精密度、准确度，采样效率，样品的稳定性进行了研究，并应用于燃煤，燃油锅炉排气中ＳＯ２浓度的测定，同时与碘量法结果进行比较和评价，表明注射器采样甲醛法测定了ＳＯ２基本可行。     

车用乙醇汽油和无铅汽油对电喷汽车排放性能的影响

分别对电喷车长时间燃用乙醇汽油、无铅汽油前后的喷油器流量进行了测试,并采用轻型汽车整车排放测试系统对燃用不同油时的主要污染排放物HC、CO和NO_x进行了分析.结果表明:与无铅汽油相比,乙醇汽油能有效降低发动机排放的CO和HC(均约10%)及经过三元催化转化器作用后HC、CO和NO_x的排放,燃用无铅汽油时整车在装有三元催化转化器下的排放达到或接近欧洲1号排放标准,换用乙醇汽油后,CO降低较明显,达30%左右,HC和NO_x分别降低约18%、10%,此时排放在欧洲1号排放标准之上或接近欧洲2号排放标准;乙醇汽油还具有优于无铅汽油的其它性能,如对喷油器有轻微的清净作用,发动机排放的CO和HC恶化趋势较慢,延长三元催化转化器的使用寿命.     

Effect of injection timing,injector opening pressure and nozzle geometry on the performance of a compression ignition engine operated on non-edible oil methyl esters from different sources

Increasing cost of fossil fuels, environmental threats from exhaust emissions and their depleting nature have generated intense international interest in developing renewable and alternative fuels for internal combustion engines. This study investigates the suitability of different non-edible-derived biodiesels such as cottonseed oil methyl ester (COME), honne oil methyl ester (HnOME) and honge oil methyl ester (HOME) to four-stroke, single-cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel injection timing (IT), fuel injector opening pressure (IOP) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and HOME in the modified CI engine. IT was varied from 19° to 27° before top dead centre (bTDC) in steps of 4° bTDC; IOP was varied from 205 to 240 bar in steps of 10 bar. Nozzle injectors of three to five holes, each of 0.3 mm size, were selected for the study. It was concluded that a retarded IT of 19° bTDC increased IOP of 230 bar, and four-hole nozzle injector of 0.3 mm size resulted in overall better engine performance with increased brake thermal efficiency and reduced hydrocarbon and carbon monoxide smoke emissions for the fuels tested.     

真空加氯机及氯气吸收系统的应用

水厂应用真空加氯机代替转子加氯机，并设置氯气吸收系统，消除了 氯对环境的污染和对人体的危害，显著提出了出水余氯合格率。     

18CrNi4WA 钢渗碳针阀体开裂失效分析

目的研究18CrNi4WA钢渗碳针阀体开裂失效原因。方法通过化学成分分析、断口扫描分析、金相组织分析、能谱分析等测试手段,对18CrNi4WA钢渗碳针阀体的断裂模式及失效原因进行分析。结果针阀体失效件原始材料符合针阀体制造要求,但渗碳淬火温度过高,未得到最优的渗碳层组织,燃油中存在的硫元素导致喷油孔位置产生严重腐蚀,燃油局部压力的变化导致针阀体表面产生空蚀损伤,裂纹起始于喷油孔圆周面,自裂纹源向外发散呈月牙状,为典型疲劳断裂特征。结论腐蚀与空蚀损伤的协同作用加快裂纹的萌生,使针阀体在热疲劳及机械振动等交变载荷的作用下产生疲劳开裂,使用寿命大为降低。