预氧化聚丙烯腈/g-C3N4光催化降解罗丹明B

以聚丙烯腈(PAN)和g-C_3N_4为原料,采用超声波辅助分散的溶液浸渍法及煅烧法制备了具有共轭结构的预氧化聚丙烯腈/g-C_3N_4复合光催化剂(CPAN/g-C_3N_4),采用XRD、SEM、FTIR、UV-Vis DRS、EIS等技术对光催化剂进行了表征,考察了CPAN/g-C_3N_4对罗丹明B(Rh B)的可见光催化降解性能。结果表明:CPAN与g-C_3N_4具有良好的协同作用,使g-C_3N_4片状结构堆叠体颗粒显著减小,明显增强了光催化剂在全部光谱范围内的光吸收,有效提高了光生电子-空穴分离效率;在PAN与g-C_3N_4质量比为1∶200、煅烧温度250 ℃、煅烧时间1 h条件下所制备的CPAN/g-C_3N_4光催化活性最高,且具有良好的光催化活性稳定性。超氧自由基和光生空穴为CPAN/g-C_3N_4复合光催化剂光降解罗丹明B的主要活性物种。     

基于多孔环形喷嘴的可燃爆粉尘分散特征的密度效应研究*

为了研究不同密度的可燃爆粉尘在内置多孔环形喷嘴的20 L爆炸特性测试装置中的分散特征，基于负载粒子流方法、耦合DPM动量平衡方程和时间平均 Navier Stokes控制方程组，实现3种不同密度的煤粉、铝粉和锆粉在20 L爆炸测试装置中粉尘分散全过程的数值模拟。研究结果表明:多孔环形喷嘴的分散较为均匀，但是约束管道末端存在局部粉尘残留区，致使爆炸仓内真实粉尘浓度远低于形式浓度；爆炸仓中心位置的最大湍动能随着粉尘密度的增加而减小，只有显著地变化粉尘密度才能展示区分度较高的浓度峰值和抵达浓度峰值的时间。     

武汉市秋季PM2.5中硫酸盐、硝酸盐理化特征及影响因素

为了解武汉市秋季PM_(2.5)中硫酸盐、硝酸盐理化特征,2016年9—11月利用热还原法在线连续监测分析系统对此进行了采样分析,并同步收集气象因子和离子色谱方法监测结果。结果表明,硫酸盐、硝酸盐的热还原分析方法与离子色谱法的相关系数分别为0.88、0.94;PM_(2.5)中硫酸盐、硝酸盐的水溶性部分占比达92.5%,难溶性部分为7.5%;空气质量为优、良和轻度污染时,硫酸盐、硝酸盐与PM_(2.5)的占比分别为45%、42%、45%;硫酸盐、硝酸盐在降水日和非降水日平均质量浓度分别为(19.6±18.5)μg/m~3和(31.0±9.1)μg/m~3;硝酸盐与硫酸盐的质量比为1.1,高于国内其他城市,与武汉市机动车保有量大幅增加有关。     

300MW燃煤锅炉机组超细颗粒聚并器的实验研究

为了解决燃煤锅炉烟气中超细颗粒难以脱除的问题,基于流体动力学原理设计了一种超细颗粒聚并器,并在300 MW燃煤锅炉机组电除尘器的前置烟道中进行了实验研究。结果表明,聚并器内部存在超细颗粒之间以及超细颗粒与大颗粒之间的相互聚集行为,从而使超细颗粒数量显著减少。例如,对于粒径在2.65和10.48μm以下的颗粒,其体积比例在聚并器出口分别减少了56.7%和62.3%,在电除尘器出口的粉尘浓度减少了26.34 mg/Nm3,这表明,基于流体动力学原理的聚并器对超细颗粒的聚并作用明显,具有良好的应用前景。     

综合管廊内火灾自动报警探测器实验研究

为了能够有效提升综合管廊内火灾自动报警系统的准确性和可靠性,本文采用火灾实体试验的方法,通过对各类型火灾自动报警探测器响应时间的情况进行分析和比较,研究综合管廊电力舱内常用探测器的性能。研究结果表明:接触式缆式线型感温火灾探测器可以较早的探测到电缆温度异常变化的现象,可用于早期预警。点型感烟探测器对烟粒子浓度较为敏感,可用于综合管廊电力舱室的空间探测。分布式光纤型感温火灾探测器对明火温度的变化较为敏感,作为空间型的火灾探测器比较可靠。     

深部煤层钻屑粒度随钻进深度分布规律

为了研究煤层钻屑粒度随钻进深度分布规律，选取具有冲击危险性的平煤八矿己15煤作为研究对象，采取钻屑量测试和孔口瓦斯浓度监测，通过筛分实验煤样并应用Rosin Rammler分布模型，探究了钻屑粒度和钻屑量大小随孔深变化关系，分析不同点钻屑粒度分布特征。结果表明:小于0.075 mm钻屑粒度分布随孔深变化与钻屑量变化规律相吻合；不同钻孔随深度变化分别对应不同Rosin Rammler分布函数，随着应力过渡越平缓，粒径分布宽度系数n值越小，煤体应力越大粒径相关系数D越大；不同范围钻屑粒度占比大小也会影响钻屑量大小；在钻屑量较大时，孔口瓦斯体积分数会出现增高现象。通过对钻屑粒度分布规律分析，更好地了解深部煤体应力分布，有助于冲击危险的预警。     

CFD simulations of dust dispersion in the 1 m3 explosion vessel

According to standard procedures, flammability and explosion parameters for dusts and dust mixtures are evaluated in 20 L and/or 1 m³ vessels, with equivalent results provided a correct ignition delay time (60 ms in the 20 L vessel; 600 ms in the 1 m³ vessel). In this work, CFD simulations of flow field and dust concentration distribution in the 1 m³ spherical vessel are performed, and the results compared to the data previously obtained for the 20 L. It has been found that in the 1 m³ vessel, the spatial distribution of the turbulent kinetic energy is lower and much more uniform. Concerning the dust distribution, as in the case of the 20 L, dust is mainly concentrated at the outer zones of the vortices generated inside the vessel. Furthermore, an incomplete feeding is attained, with most of the dust trapped in the perforated annular nozzle. Starting from the maps of dust concentration and turbulent kinetic energy, the deflagration index K_St is calculated in both vessels. In the conditions of the present work, the K_St is found to be 2.4 times higher in the 20 L than in the 1 m³ vessel.     

灰霾天气成因危害及控制治理

随着经济社会发展、城市迅速扩大和城市化进程加快,大气气溶胶污染日趋严重,由气溶胶颗粒物造成能见度恶化事件越来越多,灰霾天气已成为一种常见环境灾害污染事件。简要概述了灰霾天气定义分级、分布特征与雾霾比较,深入研究了灰霾天气形成原因、影响因素与存在危害,系统探讨了灰霾天气控制措施、监测方法与治理对策。指出在现有灰霾天气成因危害及控制治理状况下,加强理念宣贯,建立预报预警,开展PM2.5防治,推进城区绿化,科学布设规划,可有效解决中国资源节约型、环境友好型、生态文明型可持续发展过程中所面临灰霾天气防控治理问题。     

Investigation of the hydrodynamic behavior of diatom aggregates using particle image velocimetry

The hydrodynamic behavior of diatom aggregates has a significant influence on the interactions and flocculation kinetics of algae. However, characterization of the hydrodynamics of diatoms and diatom aggregates in water is rather difficult. In this laboratory study, an advanced visualization technique in particle image velocimetry (PIV) was employed to investigate the hydrodynamic properties of settling diatom aggregates. The experiments were conducted in a settling column filled with a suspension of fluorescent polymeric beads as seed tracers. A laser light sheet was generated by the PIV setup to illuminate a thin vertical planar region in the settling column, while the motions of particles were recorded by a high speed charge-coupled device (CCD) camera. This technique was able to capture the trajectories of the tracers when a diatom aggregate settled through the tracer suspension. The PIV results indicated directly the curvilinear feature of the streamlines around diatom aggregates. The rectilinear collision model largely overestimated the collision areas of the settling particles. Algae aggregates appeared to be highly porous and fractal, which allowed streamlines to penetrate into the aggregate interior. The diatom aggregates have a fluid collection efficiency of 10%-40%. The permeable feature of aggregates can significantly enhance the collisions and flocculation between the aggregates and other small particles including algal cells in water.     

Ultrafine particle emission characteristics of diesel engine by on-board and test bench measurement

This study investigated the emission characteristics of ultrafine particles based on test bench and on-board measurements. The bench test results showed the ultrafine particle number concentration of the diesel engine to be in the range of (0.56-8.35) × 10⁸ cm^-3. The on-board measurement results illustrated that the ultrafine particles were strongly correlated with changes in real-world driving cycles. The particle number concentration was down to 2.0 × 10⁶ cm^-3 and 2.7 × 10⁷ cm^-3 under decelerating and idling operations and as high as 5.0 × 10⁸ cm^-3 under accelerating operation. It was also indicated that the particle number measured by the two methods increased with the growth of engine load at each engine speed in both cases. The particle number presented a "U" shaped distribution with changing speed at high engine load conditions, which implies that the particle number will reach its lowest level at medium engine speeds. The particle sizes of both measurements showed single mode distributions. The peak of particle size was located at about 50-80 nm in the accumulation mode particle range. Nucleation mode particles will significantly increase at low engine load operations like idling and decelerating caused by the high concentration of unburned organic compounds.