Air Temperature Changes in a Steppe Marmot Burrow in the Summer–Autumn Period

Observations of air temperature changes in a steppe marmot burrow were performed from late July to mid-October. Until early September, temperature in the burrow remained relatively constant, but then it began to decrease rapidly. This occurred after air temperature above the ground became equal to the temperature in the burrow. Supposedly, it is in this particular period that marmots begin to plug the entrance to the burrow with earth, thus reducing heat exchange between the increasingly cold aboveground air and the air in the burrow.     

生态土壤渗滤系统启动周期研究

利用室内模拟试验装置,考察了4种生态土壤渗滤系统在0.1 m3/(m2·d)的水力负荷条件下对生活污水中TP、COD和NH3-N的去除效果及启动周期; 同时对整个系统及同类生态工艺启动周期的判断方法做了探讨.研究结果表明,生态土壤渗滤系统对TP、COD和NH3-N的启动周期分别为15～27 d、24～40 d和24～26 d; 土壤渗滤系统对TP的启动周期最短,对COD的启动周期最长; 处理系统启动周期的判断原则是综合考察系统对主要污染物各自的启动周期,以最长的作为系统启动周期.4组试验中,1#和2#系统的启动周期为40 d; 3#和4#的为24 d.     

基于维纳过程的MEMS陀螺仪贮存寿命评估

目的 针对MEMS陀螺仪在步进应力加速试验条件下获取的性能退化数据,提出基于维纳过程的贮存寿命评估方法及其模型准确度检验方法。方法 首先,确定温度为影响MEMS陀螺仪性能退化的主要环境因素,采用步进温度应力加速试验的方式获取其性能退化数据。其次,分析各项性能参数的演变规律,确定标度因数为表征产品性能退化的特征性能参数。最后,采用漂移维纳过程对标度因数退化轨迹进行建模,并外推得到常温条件下的贮存寿命。结果 采用留一法对模型精度进行验证,模型准确度最低为86.44%。可靠度水平为0.95时,常温贮存(25 ℃)条件下的寿命评估结果为50.02 a。结论 基于维纳过程建立的性能退化模型的准确度在85%以上,该模型可应用于指定贮存条件下MEMS陀螺仪的性能退化预测及贮存寿命评估。     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

农闲期城郊农田灌溉水中典型污染物含量与评价——以西北江三角洲为例

摸查了农田灌溉系统水环境经农（夏）闲期降水等外部强干预调理后的环境污染物含量——该值理论上是环境自净作用之后的最不利值,对农田灌溉系统水环境进行水质评价,探究其对农田土壤质量的潜在污染风险.于2019年6月中旬—7月下旬（降雨集中期）,分别在西北江三角洲城市（清远市、佛山市和江门市）实验基地周边筛选研究区,并在雨后对有覆水的水源区域、灌渠、蓄水池和田间水等采集上覆水,共采得水样27×2份,对其pH值、悬浮物（SS）、矿化度、总磷（TP）、氨氮（NH₄⁺-N）、Cd、As、Pb、Cu和Zn的含量进行检测;对各研究区pH值、SS的成因和影响,矿化度的等级,重金属均值分布等进行分析;对全样品TP、NH₄⁺-N、重金属含量进行Pearson相关性分析和描述性特征分析;通过单因子水质标识指数P_i和综合水质标识指数P分别对各采样点、各构成项目和各研究区进行水质评价.研究发现雨后农田灌溉系统水环境构成复杂,物质呈无显著性差异的迁移,灌溉沿程上覆水中大部分物质可能处于动态平衡,受局部环境影响变小,TP、NH₄⁺-N和重金属等迁移物质主要还是灌溉水体中原有的,受外力驱动扰动后在水动力作用下可能以氮磷结合形态沿灌溉系统发生远距离迁移;使用河流水质标识指数法评价农田灌溉系统水环境,发现该法可以刻画局部灌溉的水质态势,对农田灌溉系统水环境的含量特征评价做出科学、合理的解释,也可以做出综合性定量评价.虽然灌溉水系统结构差异较大,但是从整体上可以初步得出农闲期西北江三角洲农田灌溉水的灌溉风险不高的结论,总体综合水质评价级别为Ⅰ类~Ⅱ类,达到水环境功能区的使用要求.     

基于生物膜法磷回收工艺厌氧释磷研究

城市污水经过碳回收后的低碳源进水水质将对活性污泥法强化除磷（EBPR）工艺的运行带来困难.本研究基于生物膜法磷回收的序批式反应器（Biofilm-SBR）对低碳、低磷进水进行磷回收,在BSBR反应器好氧无碳源、厌氧低碳源投加的运行基础上,研究了该工艺在低碳模式下厌氧磷释放的关键影响因素.同时,研究了不同的碳源浓度和碳源投加方式对BSBR工艺释磷的影响.最后,分析了系统中生物膜蓄磷量的变化,并探究其与碳源消耗、释磷效果的量化关系.结果表明,该系统在好氧无碳源、厌氧仅200 mg·L^-1的碳源投加下,即可取得115 mg·L^-1（可溶性磷）的富磷回收液.系统的C_upt/P_rel（释放单位质量磷的COD消耗量）平均为（11.12±1.03）mg·mg^-1,最大蓄磷量为124 mg·g^-1.     

喜凉作物生长期对全球变暖停滞响应的时空差异——以中国绿洲为例

基于中国绿洲喜凉作物（chimonophilous crop）分布区39个站点1960~2016年逐日平均气温资料,运用线性趋势法、反距离加权插值（IDW）、Morlet小波、Mann-Kendall检验等方法,研究中国绿洲喜凉作物气候生长期的时空变化对变暖停滞的响应.结果表明：①变暖停滞期,中国绿洲喜凉作物气候生长期起、止日及生长期日数以-0.2d/10a、0.33d/10a、0.53d/10a的趋势变化,较1960~2016年起始日提前趋势减缓1.01d/10a,终止日推迟减缓1.28d/10a,生长期日数延长减缓2.3d/10a,对变暖停滞有响应.②中国绿洲喜凉作物气候生长期起始日对变暖停滞响应的站点有44%,终止日和生长期日数均为49%,主要分布在南疆、柴达木盆地和河西绿洲,其中河西绿洲对变暖停滞响应最明显,南疆次之,柴达木最小,而北疆绿洲不存在滞缓现象,显然空间差异明显.③M-K检验显示,中国绿洲喜凉作物气候生长期起、止日及生长期日数分别在2001年、1990年和1997年发生突变,起始日晚于变暖停滞起始年份,终止日和生长期日数早于变暖停滞起始年,且分绿洲生长期日数突变年与变暖停滞起始年相接近.④Morlet小波得出变暖停滞期其变化稳定存在2.4~4.3a的震荡周期,表明未来几年中国绿洲喜凉作物气候生长期仍持续延长.     

辽宁西部人工林油松径向生长对气候要素的响应

全球气候变化对森林生态系统产生广泛影响,特别是对气候响应敏感的农牧交错带。辽西丘陵位于我国农牧交错带东北部,为探究辽西丘陵人工林油松径向生长与气候要素的关系,基于树木年代学方法,利用树轮宽度年表,对温度、降水、scPDSI及生长期要素进行相关分析,探究气象因子对树木径向生长的影响情况。结果表明：油松标准化年表与上年7月、9月及当年5月的气温呈负相关,相关系数分别为?0.457、?0.426、?0.471（p<0.05）,与当年5月的降水量呈正相关,相关系数为0.52（p<0.05）;年表与逐月scPDSI显著正相关,并表现出相近的周期变化,表明水分胁迫是研究区油松生长的关键限制因子;在不同阈值温度下,辽西人工林油松径向生长与生长期活动积温和持续天数呈负相关,由高温引起的水分蒸发是影响其径向生长的关键因子。最低温11℃阈值下对树木生长期影响大,年表与其初日位序、积温、持续天数的相关系数分别达到0.663、?0.619、?0.732（p<0.01）;通过V-S模型模拟出辽西油松的生长对春季的9.0℃和秋季的9.5℃较敏感,生长期为4—10月,生长速率的变化受温度和土壤湿度变化的影响。因此,在进行人工油松林区经营抚育时,可适当考虑造林树种对不同气候因子响应的敏感期,注意水热合理配置,以提高林区生态林的营林质量。     

Ignition temperatures of dust layers and bulk storages in hot environments

In many industrial installations, particulate solids (cereals, agri-food products, coal, plants, etc.) are stored or processed. Self-heating of these products, which can lead to fires and explosions, can occur in a variety of situations. Examples include large storage at room temperature, formation of a layer on a hot surface, layer deposited on a surface – insulating or conductive – in a hot environment or even storage of product exposed to heating on one side.The main parameters that determine the occurrence of self-heating are the size of the container, the temperature, the residence time and the characteristics of the product. Depending on the type of situation encountered and these implementation conditions, the analysis of self-heating risks must be based on specific models and/or parameters.This paper presents the different variants and combinations of the theoretical model from the theory of thermal runaway to represent self-heating, taking into account in particular the symmetry or asymmetry of heating, reagent consumption and boundary conditions. It also discusses their adaptation to the previous identified industrial situations.Nine products were chosen to be representative of those used in the different considered industrial situations. They were subjected to self-heating basket tests in isothermal ovens in order to determine the parameters for applying the described theoretical models. These results were compared with the results of self-heating tests in layers of different thicknesses in a hot environment, on an insulating or conductive plate, using a specially developed test protocol, as well as with the results of standardized tests of minimum ignition temperature in 5 mm layers.This led to the proposal of the most appropriate theoretical model to represent the self-heating phenomenon for each of the four identified industrial situations.This analysis can promote better design of industrial equipment and production conditions (temperatures, volumes or product flows …) in order to prevent fires and explosions.     

Transformation of Organic Matter of the Larch Forest Soils in the Northern Taiga of Nizhne-Tungusskoe Plateau, Central Siberia

The evaluation of biospheric role of the boreal forests in the accumulation of carbon is connected with the evaluation of organic matter (OM) pool in soils. The research sites were larch forests, they are situated on Nizhne-Tungusskoe Plateau. Larch forests of feather-moss and lichen types (110 and 380 years old) were formed on 'ochric podbur' soils. Litter stocks are 3.5–4.5 kg m^{− 2} with thickness 10–25 cm. Cryomezomorphic northern taiga soils contains 38–73 t (carbon) ha^{− 1}. Pool of fast mineralized OM has average value 38.1 t (carbon) ha^{− 1}, including 20.5 and 6.4 t (Carbon) ha^{− 1} of labile compounds on surface and in the soil, and 11.2 t (carbon) ha^{− 1} of mobile OM. Microbial mass reaches 1.78–3.47 t (carbon) ha^{− 1}, its proportion is 3.6–4.9% of the total OM carbon. Zoomass of feather-moss larch forest is 0.20–0.61 * 10^{− 2}, in lichen larch forest −0.01–0.07 * 10^{− 2} t (carbon) ha^{− 1}. A pool of resistant to biological decomposition and bonded to mineral soil matrix OM is 17.7 t (carbon) ha^{− 1} and it varies from 18.6 to 29.0 in feather-moss larch forest, and from 6.4 to 17.0 t (carbon) ha^{− 1} in lichen larch forest. Two-years field experiment has been performed to determine transformation rates of various plant litter fractions and to clarify the role of soil biota in these processes. The results showed participation of all biota groups in the decomposition of plant residues caused weight loss of larch-needles and root mortmass. Isolation of organic matter from all-size invertebrate groups leads to some decrease of decomposition activity.