Numerical simulation of far-field blast loads arising from large TNT equivalent explosives

Large TNT equivalent explosions usually arise from accidents occurring during the transportation, storage, and manufacturing of chemicals relevant to process industries. The blast wave generated by the explosion will spread and interact with the surrounding factories and storehouses, damaging the building structures within several kilometers and causing significant casualties and property losses. This study aims to develop an efficient numerical simulation method to predict blast loads to estimate the consequences of accidents involving far-field free air bursts or surface burst explosions. Before its interaction with the interested target, a blast wave is generated in the numerical model by specifying the initial and boundary conditions of the disturbed air. Based on empirical data of incident overpressure, an explicit formula to calculate the air particle velocity is derived from the governing equations of a perfect inviscid gas. A simplified path line method is proposed to calculate the air density. The proposed method is applied to the LS-DYNA CESE solver to simulate the blast loads on building structures in the far field. Validations against empirical data and experiments indicate that the proposed method is sufficiently accurate for engineering applications and, through a case study, presents a more efficient performance than the LOAD_BLAST_ENHANCED (LBE) and mapping methods.     

A multidecadal oscillation in precipitation and temperature series is pronounced in low flow series from Puget Sound streams

In Pacific Northwest streams, summer low flows limit water available to competing instream (salmon) and out-of-stream (human) uses, creating broad interest in how and why low flows are trending. Analyses that assumed linear (monotonic) change over the last ~60 years revealed declining low flow trends in minimally disturbed streams. Here, polynomials were used to model flow trends between 1929 and 2015. A multidecadal oscillation was observed in flows, which increased initially from the 1930s until the 1950s, declined until the 1990s, and then increased again. A similar oscillation was detected in precipitation series, and opposing oscillations in surface temperature, Pacific Decadal Oscillation, and Interdecadal Pacific Oscillation series. Multidecadal oscillations with similar periods to those described here are well known in climate indices. Fitted model terms were consistent with flow trends being influenced by at least two drivers, one oscillating and the other monotonic. Anthropogenic warming is a candidate driver for the monotonic decline, and variation in (internal) climatic circulation for the oscillating trend, but others were not ruled out. The recent upturn in streamflows suggests that anthropogenic warming has not been the dominant factor driving streamflow trends, at least until 2015. Climate projections based on simulations that omit drivers of multidecadal variation are likely to underestimate the range, and rate of change, of future climatic variation.     

Enhancing the adsorption function of biochar by mechanochemical graphitization for organic pollutant removal

• Mechanochemical treatment reduced the calcination temperature for biochar synthesis. • Biochar is converted to graphite after mechanochemical treatment. • Biochar was reduced to nanoscale after mechanochemical treatment. Biochar (BC) has been extensively studied as adsorbent for the treatment of water pollution. Despite the distinct advantages, the high calcination temperature and low adsorption capacity of pristine BC limit its practical applications. Most of the former studies focused on the structure and/or surface modification to improve the adsorption capacity of BC. However, the harsh experiment conditions involved in the biochar modification limited the application in industrial level. Herein, we introduced mechanical treatment into BC preparation to reduce the calcination temperature and improve the adsorption capacity simultaneously. The results indicated that the calcination temperature was reduced and the adsorption capacity of the treated BC was improved after mechanochemical treatment. Characterization of the samples disclosed that BCs were graphitized with the particle size reduced to nanoscale after treatment. Adsorption tests indicated that the mechanochemically treated BCs showed much better removal performance of organic contaminants than that of pristine BCs. For instance, among four pristine BCs (BC600, BC700, BC800, and BC900), only BC900 has strong adsorption capacity for MB, while BC600 has low adsorption capacity (1.2 mg/g). By comparison, the adsorption capacity of MB increased greatly to 173.96 mg/g by BC600-500/1 (treated at 500 r/min for 1 hour). To optimize the mechanochemical treatment, the effects of rotation speed and agitation duration were also investigated.     

Effects of EGR on performance and emissions of a diesel engine fuelled with balanites aegyptiaca/diesel blends

In this study, balanites Aegyptiaca (L.) Del biodiesel was blended in proportions of 10% and 20% on the volume basis with diesel fuel and tested in a single cylinder, VCR diesel engine under measured load conditions with varied EGR rates (0, 10 and 20%). The results showed that B10 and B20 blends shown a significant reduction rate in terms of NO_x emissions that were familiar with biodiesel blends. At peak load conditions, BTE increased slightly for test fuel blends compared with pure diesel fuel while the BSFC rate and EGT suffered from increasing and decreasing nature with respect to blending percentage. From the emissions point of view, with the increase in blends percentage, a significant reduction rate is observed in terms of CO and HC concentrations (up to 12.34 and 17.5%, respectively) while NOx emissions decreased at peak load conditions (up to 24.34%). HC and CO emissions decreased with increase in blends percentage. However, lower levels of NO_x and EGT (up to 21.37 and 8.47%, respectively) and the average increase in terms of BTE and BSFC (up to 2.83 and 2.9%, respectively) can be realised with B20 test fuel blend under 20% EGR rate.     

新制备生物炭的特性表征及其对石油烃污染土壤的吸附效果

生物炭作为一种绿色环保的功能材料因其在污水处理和污染土壤修复方面具有显著效果而受到极大关注.采用红外光谱、元素分析仪及微孔分析对不同温度(200、300、400、500和600℃)条件下制备的木屑和麦秆生物炭进行特性表征,并采用制备的生物炭净化石油污染土壤,分别考察了污染物性质、生物质原料和热解温度对其净化效果的影响.结果表明,随着热解温度的增高,生物炭芳香化程度增加,极性降低,微孔结构逐渐发育,表面积增大.加入生物炭33 d后,污染土壤中总石油烃及其组分烷烃的浓度比对照略有降低,而PAHs浓度下降显著.随着热解温度升高,2种生物炭对PAHs的吸附强度均逐渐增大,芳香度增高、表面积增大是强吸附的主要原因.2种生物炭在400℃及以下温度制备时对PAHs的吸附强度为:木屑生物炭＞麦秆生物炭;而400℃以上温度制备的生物炭吸附强度则相反,即麦秆生物炭＞木屑生物炭,说明生物炭原料对其吸附强度也具有显著影响.     

引水放流方式对太湖贡湖示范区水质的影响

基于国家水专项太湖贡湖湾示范区水质水量调控的需求,构建了示范区的等比例缩放实体模型。通过研究模型中4种不同调水方案的效果,为示范区调水技术的比较与选择提供决策依据。研究中,通过测定模型中5个断面的流场数据,判断引水方式对模型流场的影响,以此评价不同调水方案效果。同时以墨汁作为示踪剂,通过不同引水放流方式下示踪剂的扩散场变化,验证不同断面流速测定对整个区域流场判断的准确性,从而分析引水放流方式对水质的影响。     

化学环境下的应力-渗流耦合对尾 矿库稳定性影响试验

通过扫描电镜（FE-SEM）、能谱分析（EDX）、X射线衍射（XRD）、LMS-30激光粒度分析等室内试验探究了尾矿库内存在的酸、碱离子对尾矿颗粒的沉降、微观形貌、物质组成以及粒径级配的影响；建立酸、碱影响下的孔隙比与渗透系数的数学关系模型，并将建立的模型用来表征尾矿库内的应力渗-流场两场耦合机制，实现代入有限元计算软件的目的。结果表明:化学因素的存在影响着尾矿颗粒的多项性状，酸性环境下尾矿颗粒发生溶蚀，部分金属元素流失；碱性环境下尾矿颗粒间生成胶结物质，孔隙出现以含氢氧化铁为主的絮状、团簇状堵塞物，改变了渗流速度；尾矿库内浸润线高度在碱性、中性、酸性环境下依次降低，而渗流速度依次升高。     

高温高压下煤孔隙结构的变化对瓦斯吸附特性的影响

为了研究高温高压条件下煤孔隙结构变化对瓦斯吸附特性的影响，选取九里山矿无烟煤，在压力为7 MPa、温度为40～130℃的条件下进行等温吸附实验和压汞实验。研究结果表明:煤样对甲烷的等温吸附曲线在该压力、温度条件下符合Ⅰ型吸附曲线特性，吸附规律符合Langmuir吸附模型；在压力7 MPa和温度130℃条件下，煤样的孔隙结构发生一定的变化，煤的比表面积增大、累计孔体积降低，可见孔及裂隙的数量比例增高，加强了煤样孔隙之间的连通度，导致原本吸附在煤样表面的甲烷分子大量解吸；在压力不变的情况下，随着温度的不断增高，煤的极限吸附量逐渐减小，其主要原因是样品孔隙结构的破坏和分子间作用力的变化。     

基于Landsat 8遥感数据的天津市地表温度反演

以Landsat 8遥感数据为数据源,进行天津市地表温度反演研究。首先采用单通道算法反演地表温度,并利用均值标准差法进行温度分级。然后建立不同温度等级面积比例的估算模型。再通过随机样点,从不同温度等级和土地覆盖类型2个角度,分别建立并比较不同类样点的地表温度与各指数的拟合模型。结果表明:次高温区域面积比例与人口密度、人均GDP都具有较高的决定系数;地表温度与NDVI、BAEM的二元线性回归决定系数高于地表温度与单一指数的决定系数;将样点分类后,低温点与MNDBI的决定系数高于其他温度等级样点,水域和植被样点与各种指数的决定系数高于其他地物类型样点。     

Spatial and Seasonal Response of Municipal Water Use to Weather across the Contiguous U.S.

Weather variability has the potential to influence municipal water use, particularly in dry regions such as the western United States (U.S.). Outdoor water use can account for more than half of annual household water use and may be particularly responsive to weather, but little is known about how the expected magnitude of these responses varies across the U.S. This nationwide study identified the response of municipal water use to monthly weather (i.e., temperature, precipitation, evapotranspiration [ET]) using monthly water deliveries for 229 cities in the contiguous U.S. Using city‐specific multiple regression and region‐specific models with city fixed effects, we investigated what portion of the variability in municipal water use was explained by weather across cities, and also estimated responses to weather across seasons and climate regions. Our findings indicated municipal water use was generally well‐explained by weather, with median adjusted R² ranging from 63% to 95% across climate regions. Weather was more predictive of water use in dry climates compared to wet, and temperature had more explanatory power than precipitation or ET. In response to a 1°C increase in monthly maximum temperature, municipal water use was shown to increase by 3.2% and 3.9% in dry cities in winter and summer, respectively, with smaller changes in wet cities. Quantifying these responses allows urban water managers to plan for weather‐driven variability in water use.