非柔性连接石化储罐配管温差应力分析与对策

储罐配管在温差作用下产生热位移会导致管壁产生热应力，未采用柔性连接的配管由于热应力集中作用可能发生破漏。针对与石油化工储罐非柔性连接的配管的安全问题，应用ANSYS有限元分析软件模拟计算石化企业典型配管的热应力分布；根据不同类型配管的分析结果，提出了工程技术与管理方面的针对性安全措施。研究结果表明:温差效应对石化储罐配管热应力影响显著，随内外温差的增加，配管应力集中的区域增大，最大热应力值增大；补偿措施能够改善配管的柔性，降低配管应力；约束载荷限制配管热膨胀从而增大配管应力；三通管是多根配管接合的区域，这种复杂管道交汇处会形成明显应力集中。研究结果对于提高石油化工非柔性连接配管安全性有一定的指导意义。     

呼吸效应对矿井封闭火区氧浓度的影响分析

为避免因火区封闭导致重大安全事故发生，通过采集某矿井1 d内3个不同监测点的大气压力变化情况，建立大气压力波动模型并分析计算，同时建立火区内外压差100，750 Pa情形下的氧浓度模型进而获得火区内侧氧气浓度因呼吸效应，在不同压差、体积大小火区、风阻、瓦斯涌出量、封闭时刻等多因素耦合影响下随时间的变化规律，以评估火区危险性。研究结果表明:井下大气随地面大气周期波动，封闭火区内、外侧之间的气压差因外界大气波动呈现16 h的余弦波动和8 h的线性波动周期变化；密闭质量好的火区具有更好地抗干扰性，内侧氧浓度的降低主要依靠瓦斯稀释；密闭质量差的火区，内侧氧浓度易受到火区涌出瓦斯、外界涌入大气双重影响；火区氧浓度在2%~12%之间波动，以至火区存在发生瓦斯爆炸的可能性；火区内外压差较大时，氧浓度波动变化幅度更大，危险作用持续时间更长。结合火区氧浓度波动模型，可有效地对矿井火区采取安全的防范措施，避免瓦斯爆炸事故发生。     

肥煤自燃全过程热动力学特征参数研究

实验测定了林西矿肥煤样品30~900℃煤自燃全过程热动力学特征参数,得出:TG/DTG曲线显示煤样DTG初始临界温度45℃,干裂温度122℃,活性温度195℃,增速温度265℃,质量极大值温度342℃,着火温度465℃,最大热失重速率温度515℃和燃尽温度690℃;DSC曲线显示,煤样初始放热温度60℃、最大热释放速率温度511℃。结合TG-DTG-DSC曲线综合分析可知,煤温达到510℃左右时煤样反应最剧烈。由煤自燃标志气体测定实验系统得出:煤温130℃后CO,CO 2释放量迅速增加,210℃增加速度下降;CH 4,C 2 H 6含量变化具有规律性且两者变化相近;C 2 H 4出现温度为130℃;C 2 H 4/C 2 H 6比值在190~350℃有较强的规律性,呈上升趋势且上升速度较快;350℃之后,CH 4,C 2 H 6,C 2 H 4体积分数均开始急剧增大;C 2 H 4/CO与C 2 H 4/CO 2变化趋势大致相同,在130~350℃时缓慢增长,达到350℃后比值呈指数形式上升。经拟合曲线,得到活化能的3个突变点温度:70,180,220℃,其中180℃与交叉点温度相吻合。通过以上研究,得到了肥煤自燃全过程的热力学特征参数,为实际生产中防治煤自燃提供了理论依据。     

Experimental research of LNG accidental underwater release and combustion behavior

Evaluating potential hazards caused by accidental LNG release from underwater pipelines or vessels is a significant consideration in marine transportation safety. The aim of this study was to capture the dynamic behavior of LNG jet released under water and to analyze its vapor dispersion characteristics and combustion characteristics on the water surface during different release scenarios. Controlled experiments were conducted where LNG was jet released from a cryogenic storage tank. The dynamic process of LNG being jet released from orifices of different sizes and shapes, as well as the rising plume structure, were captured by a high-speed camera. The leakage flow rate and pipeline pressure were recorded by a flow meter and pressure gauge, respectively. The concentration distribution that emanated from the water surface was measured utilizing methane sensors in different positions with various wind speeds. The flame combustion characteristics of LNG vapor clouds, which immediately ignited upon the enclosed water tank, were also recorded. Additionally, the mass burning rate of the flame on the water surface was evaluated, and a new correlation between the ratio of flame length and width was established. The results indicated a large dimensionless heat release rate (Q*) and a continuous release flow rate in a limited burning area. This study could provide greater understanding of the mechanisms of LNG release and combustion behavior under water.     

2013-2017年京津冀区域PM2.5浓度变化特征

利用2013-2017年京津冀区域13个城市PM_2.5监测数据，综合探讨了该区域PM_2.5浓度的时空变化特征。结果表明：京津冀区域PM_2.5污染整体较重，但治理成效显著，2013-2017年区域PM_2.5年均质量浓度分别为106、93、77、71、64 μg/m³，完成《大气污染防治行动计划》PM_2.5浓度下降25%左右的目标；13个城市PM_2.5浓度各百分位数总体呈现下降趋势，且随百分位数增大而下降速率加大，PM_2.5年均质量浓度平均每年下降10.6 μg/m³，污染严重的太行山沿线城市邢台、石家庄、邯郸3个城市平均每年分别下降20.3、16.1、13.9 μg/m³；京津冀区域PM_2.5重度污染天数比例分别为19.9%、16.6%、9.5%、9.0%、7.0%，呈下降趋势。2013-2017年京津冀区域PM_2.5平均质量浓度与非重度污染天相比升高19 μg/m³，PM_2.5重度污染天平均质量浓度较非重度污染天时高244.4%。     

Usage of polystyrene disposable food dishes in the lightweight concrete making

The increasing use and subsequent accumulation of polystyrene containers has triggered a substantial environmental problem. This study investigated using varied percentages of solid waste polystyrene disposable food dishes in the production of lightweight concrete samples with 350 kilograms per cubic meter (kg/m³) of cement and a density of 1,300 kg/m³. The polystyrene disposable dishes were ground into beads of 0–3 millimeters (mm) and 3–6 mm in size. First, the characteristics of Type II Portland cement, polystyrene, and aggregates were examined. The following characteristics of concrete using ASTM International and British Standards Institution standards were tested: slump, compressive strength, ability to resist chloride ion penetration, and resistance of concrete to rapid freezing and thawing cycles. Scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy analytical techniques were also used. The slump of samples varied between 40 and 70 mm and was not dependent on either the polystyrene percentage or the size of the polystyrene beads in the concrete samples (p‐value > .05). The compressive strength of the concrete samples after 90 days of curing, and using different percentages of polystyrene, varied between 96 and 113 kilograms per square centimeter (kg/cm²). The resistance of the samples to the freezing and thawing cycle and chloride ion penetration were affected unfavorably by the presence of the polystyrene. The SEM technique indicated that concrete samples containing 15% and 25% polystyrene had denser crystals and less void than concrete samples with 40% and 55% polystyrene.     

Effects of release pressure on the transportation characteristics in pipeline and the diffusion behaviors in enclosure space of typical gas extinguishing agent

Reducing the release pressure of fire extinguishing systems can decrease potential safety hazards in large transport airplanes. To explore whether reducing the release pressure can achieve the release effect required by the airworthiness standards or not, the transportation characteristics in the pipeline and diffusion behaviors in the enclosure space of a typical fire extinguishing agent (Halon 1301) were investigated under five release pressures in the present study. The effects of the release pressure on the degree of superheat, injection duration, jet structure, and concentration distribution of Halon 1301 were analyzed. The results show that both of the degree of superheat and the injection duration decrease with an increase in the release pressure. The supplement of bubble expansion in the fire extinguishing agent can slow down the pressure decrease in the vessel. Both of the maximum and mean values of the pipeline differential pressure increase with an increase in release pressure. The maximum value of the jet angle decreases linearly with the increase in release pressure, and the jet deflects upward owing to the effects of buoyancy. The maximum concentration value decreases with an increase in the distance from the nozzle. The maximum concentration values in the near field from the nozzle increase with an increase in the release pressure. Under five release pressures, the concentration and holding time (duration above 6% volume concentration) of Halon 1301 on the centerline of the jet meet the requirements of airworthiness provisions.     

CO2浓度升高对半干旱区春小麦光合作用及水分生理生态特性的影响

大气CO₂浓度升高已成为世界范围内重要环境问题。为了解大气CO₂浓度升高对春小麦光合作用及水分生理生态特性的影响,在典型半干旱区定西利用开顶式气室(OTC)试验平台,以春小麦“定西24号”为供试品种,开展了CO₂浓度增加模拟试验。试验设对照(390μmol·mol^?1)、480μmol·mol^?1和570μmol·mol^?1等3个CO₂浓度(摩尔分数)梯度。结果表明:在对照和增加CO₂浓度条件下,春小麦叶片净光合速率和蒸腾速率日变化均呈“双峰型”分布,出现明显的“午休”现象;胞间CO₂浓度的日变化表现为斜“V”字型曲线;叶水势日变化呈现反抛物线曲线走向,在中午后出现水势曲线拐点。在不同生育时期内,净光合速率、气孔导度和胞间CO₂浓度均表现为开花期最大,乳熟期最小。而蒸腾速率表现为开花期最大,拔节期最小,叶片水平水分利用效率表现为孕穗期最大,乳熟期最小。随着CO₂浓度升高,春小麦叶片净光合速率、胞间CO₂浓度、水分利用效率和水势提高,气孔导度和蒸腾速率降低。与对照大气CO₂浓度相比,在480μmol·mol^?1浓度和570μmol·mol^?1浓度下,整个生育期净光合速率平均分别提高了14.68%和28.20%,气孔导度平均降低了15.29%和24.83%,胞间CO₂浓度平均提高了10.38%和26.15%,蒸腾速率平均减小了6.63%和12.41%,WUE平均增加了22.9%和46.9%。随着CO₂浓度升高,蒸腾失水减少,叶片水势不断增加,从而增强了春小麦对干旱胁迫的抵御能力。研究结果为我国半干旱区春小麦对全球气候变化下的敏感性及适应性提供理论参考。     

水平管内不同煤质煤尘爆炸火焰传播特性实验研究

为研究水平管道空间不同煤质煤尘爆炸火焰传播特性，选取褐煤、长焰煤、不粘煤、气煤4种煤尘，对爆炸火焰焰峰特性、火焰加速传播特性、火焰传播距离与持续时间展开研究。研究结果表明:褐煤在500 ms内焰峰的形状由尖锐向平滑再向钝化不断演变，长焰煤与不粘煤在375 ms时焰峰前端出现明显焰体分离现象，分析认为这与管体冷壁效应、空间尺度效应及空间氧气消耗直接相关；气煤在375 ms时焰峰出现大面积火焰碎纹，说明气煤爆炸火焰猛烈传播的持续时间相对较短，整体爆炸强度相对较弱；褐煤与长焰煤爆炸火焰存在2次间断性加速，分析认为这与管体空间受限、常温管壁散热、局部助燃氧气瞬间不足等因素有关；褐煤在爆炸后400～600 ms内火焰2次加速完全，火焰传播距离达740 mm，明显大于长焰煤、不粘煤与气煤，说明低变质褐煤爆炸火焰持续时间更长，火焰传播距离更远且传播更剧烈；虽然气煤火焰最远传播距离比长焰煤大30 mm，但由于气煤火焰在375 ms左右出现大片火焰碎纹，因此气煤整体的爆炸强度小于长焰煤。     

汽车用聚合物材料火灾燃烧特性研究

为研究车用聚合物材料的燃烧特性，并对材料的火灾危险性进行全方位的评估，采用锥形量热仪，对汽车上常用的ABS，PP-PVC，PVC革-无纺毡以及无纺布-PVC聚合物材料进行分析表征，测得点燃时间、热释放速率、总热释放量、质量损失速率、烟气生成速率等参数。结果表明:ABS材料的点燃危险性相对最低，PVC革-无纺毡材料相对最高；随热辐射强度的增加，各样品的热释放速率和烟气生成速率明显加快；结合热释放速率峰值、均值和总热释放量可知，无纺布-PVC材料的热危险性相对最低；结合烟气生成速率和总烟释放量可知，ABS材料的发烟危害性相对最高，无纺布-PVC的相对最低；综合比较各样品的FGI和FPI值，安全等级由高到低依次为ABS，PP-PVC，PVC革-无纺毡，无纺布-PVC。