Injection-Molded Bioblends from Lignin and Biodegradable Polymers: Processing and Performance Evaluation

This paper investigates the effects of the incorporation of lignin and small quantities of epoxidized natural rubber (ENR) as an impact modifying agent on blends of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and poly(ε-caprolactone) (PCL). The addition of lignin resulted in a slight improvement of flexural strength and modulus of the ternary blending system. Incorporation of ENR into the blend resulted in an increase in notched Izod impact strength from 40 to 135% depending on the concentration of ENR. The addition of lignin into the blend resulted in an improvement of thermal stability of the ternary blend system. Morphological analysis showed a good dispersion of PHBV phases and lignin within the PCL matrix. Rheological characterization revealed that the presence of lignin resulted in increased storage modulus of the bioblend.     

Evaluation of hydroxyapatite/poly(acrylamide-acrylic acid) for sorptive removal of strontium ions from aqueous solution

Environmental Science and Pollution Research - A composite polymer, hydroxyapatite/poly(acrylamide-acrylic acid), was synthesized by gamma-induced polymerization. The factors affecting the sorption...     

Estimating Potential Climate Change Effects on the Upper Neuse Watershed Water Balance Using the SWAT Model

Climate change poses water resource challenges for many already water stressed watersheds throughout the world. One such watershed is the Upper Neuse Watershed in North Carolina, which serves as a water source for the large and growing Research Triangle Park region. The aim of this study was to quantify possible changes in the watershed’s water balance due to climate change. To do this, we used the Soil and Water Assessment Tool (SWAT) model forced with different climate scenarios for baseline, mid‐century, and end‐century time periods using five different downscaled General Circulation Models. Before running these scenarios, the SWAT model was calibrated and validated using daily streamflow records within the watershed. The study results suggest that, even under a mitigation scenario, precipitation will increase by 7.7% from the baseline to mid‐century time period and by 9.8% between the baseline and end‐century time period. Over the same periods, evapotranspiration (ET) would decrease by 5.5 and 7.6%, water yield would increase by 25.1% and 33.2%, and soil water would increase by 1.4% and 1.9%. Perhaps most importantly, the model results show, under a high emission scenario, large seasonal differences with ET estimated to decrease by up to 42% and water yield to increase by up to 157% in late summer and fall. Planning for the wetter predicted future and corresponding seasonal changes will be critical for mitigating the impacts of climate change on water resources.     

Improved desalination by polyamide membranes containing hydrophilic glutamine and glycine

Environmental Chemistry Letters - Water desalination and recycling of wastewater is a key challenge to meet water shortage issues. Thin film composite polyamide membranes are widely used for...     

Design of National Groundwater Quality Monitoring Network in Egypt

In the Nile Valley and Delta the protection of groundwater resources is high priority environmental concern. Many groundwater quality problems are already dispersed and may be widespread and frequent in occurrence. Examples include problems associated with the extensive application of chemical fertilizers in agricultural specially in the new reclaimed areas, leaks in sewers, septic tanks, the aggregate effects of many different points source pollution in urban areas and natural, geologically related water quality problems. A national groundwater quality monitoring has been designed and implemented based on the stepwise procedure. The national groundwater quality monitoring network is used to quantify the quality changes in long run, either caused by pollution activities or by salt water intrusion and to describe the overall current groundwater quality status on a national scale of the main aquifers. The monitoring tools and methodologies developed in this research can be used to assure protection of public health and determine the sustainability of groundwater in various purposes. This national monitoring network plays important roles for decision makers in developing the groundwater resources management plans in different aquifers systems in Egypt.     

Suspended particulates and bioaerosols emitted from an agricultural non-point source

Suspended particulate and bioaerosol levels were measured at three sites downwind of an agricultural non-point source during the wheat harvesting season. Suspended particulates were detected at mean values ranging from 10000 to 2420 micrograms m-3 at distances of from 20 to 60 m downwind of the source, respectively. Airborne viable bacterial counts were recorded at mean values ranging between 10(4) and 10(6) colony forming units (cfu) m-3, whereas, Gram negative (Gram -ve) bacteria varied between 10(3) and 10(5) cfu m-3. Fungi levels were detected at mean values varying between 10(5) and 10(6) cfu m-3. However, streptomycetes were found at lower counts than those recorded for viable bacteria and fungi. Total viable bacteria, Gram -ve bacteria, fungi and streptomycetes associated hay fragments were determined at mean values of 1.5 x 10(6), 1.6 x 10(3), 2.2 x 10(4) and 6 x 10(3) cfu g-1 of hay, respectively. Cladosporium, white and red yeasts as well as Alternaria were the predominant airborne fungi, whereas, Alternaria was the dominant species associated with hay fragments. Pseudomonas, Acinetobacter and Enterobacteriaceae were the dominant Gram -ve bacteria. The most common fungal genera, such as Cladosporium and Fusarium (minor short axis), as well as Streptomyces species have an aerodynamic diameter (dae) of less than 5 microns, which can penetrate and deposit in the alveoli. Farmers and nearby residents are exposed to high levels of organic dust and bioaerosols during the wheat harvesting season. This may cause health problems in exposed persons based on toxic or allergic reactions.     

Indoor and outdoor formaldehyde concentrations in homes in residential areas in Greater Cairo

Indoor and outdoor measurements of formaldehyde were conducted at seven flats located in residential areas in Greater Cairo, during spring and summer seasons 1999. The mean daytime formaldehyde concentrations in kitchens, bedrooms and living rooms were 89, 100 and 100 ppb, respectively, in the seven flats. Significant positive correlations were found between the concentrations of formaldehyde found in these three rooms. On the other hand, no significant differences were found between the mean formaldehyde concentrations in these three rooms. The maximum mean concentration of formaldehyde (147 ppb) was recorded in a new flat, while the minimum concentration (43 ppb) was observed in an old flat. The maximum hourly and daytime concentrations were 350 and 225 ppb, respectively. Air temperature, relative humidity and the age of the flat are factors affecting the emission and concentration of formaldehyde. The maximum indoor and outdoor formaldehyde concentrations were recorded during the summer season. During the spring, 38% of the samples indicated that the concentration of formaldehyde in the seven flats exceeded 0.1 ppm, the American Society of Heating, Refrigerating, and Air Conditioning Engineers' (ASHRAE) standard; in the summer, this figure increased to 53%.     

Evaluation of airborne lead in the welding working environment

Manual and automatic welding machines (which use leaded alloys) are considered to be important sources of the emission of lead fumes into the general air of the working environment. Three workplaces at a television factory were selected for the present study, to determine the control class of the working unit. The concentrations of conventional measurements ("A" sampling points) were lower than the administrative control level (statutory standard of lead, 150 microg m(-3)), whereas the maximum concentration of 264.1 microg m(-3) ("B" sampling point) was higher at one working unit than the administrative control level. However, the control classes varied between class III (bad) and class I (good).     

A novel one-step synthesis for carbon-based nanomaterials from polyethylene terephthalate (PET) bottles waste

Nowadays our planet suffers from an accumulation of plastic products that have the potential to cause great harm to the environment in the form of air, water, and land pollution. Plastic water bottles have become a great problem in the environment because of the large numbers consumed throughout the world. Certain types of plastic bottles can be recycled but most of them are not. This paper describes an economical solvent-free process that converts polyethylene terephthalate (PET) bottles waste into carbon nanostructure materials via thermal dissociation in a closed system under autogenic pressure together with additives and/or catalyst, which can act as cluster nuclei for carbon nanostructure materials such as fullerenes and carbon nanotubes. This research succeeded in producing and controlling the microstructure of various forms of carbon nanoparticles from the PET waste by optimizing the preparation parameters in terms of time, additives, and amounts of catalyst.

Implications: Plastic water bottles are becoming a growing segment of the municipal solid waste stream in the world; some are recycled but many are left in landfill sites. Recycling PET bottles waste can positively impact the environment in several ways: for instance, reduced waste, resource conservation, energy conservation, reduced greenhouse gas emissions, and decreasing the amount of pollution in air and water sources. The main novelty of the present work is based on the acquisition of high-value carbon-based nanomaterials from PET waste by a simple solvent-free chemical technique. Thus, the prepared materials are considered to be promising, cheap, eco-friendly materials that may find use in different applications.