Multiple comparisons of organic,microbial, and fine particulate pollutants in typical indoor environments: Diurnal and seasonal variations

This study was performed to investigate the possible sources as well as seasonal and diurnal variations of indoor air pollutants in widely used four different environments (house, office, kindergarten, and primary school) in which people spend most of their time. Bioaerosol levels and species, volatile organic compound (VOC) levels, and PM_2.5 (particulate matter with an aerodynamic diameter ≤2.5 μm) levels were determined in different parts of these environments in parallel with outdoor sampling. Air pollution samplings were carried out in each microenvironment during five subsequent days in both winter and summer in Ankara, Turkey. The results indicated that bioaerosol, VOC, and PM_2.5 levels were higher in the winter than in the summer. Moreover, PM_2.5 and bioaerosol levels showed remarkable daily and diurnal variations, whereas a good correlation was found between the VOC levels measured in the morning and in the afternoon. Bacteria levels were, in general, higher than fungi levels. Among the VOCs, toluene was the most predominant, whereas elevated n-hexane levels were also observed in the kindergarten and the primary school, probably due to the frequent wet cleaning during school days. According to factor analysis, several factors were found to be significantly influencing the indoor air quality (IAQ), and amongst them, VOC-based products used indoors ranked first. The overall results indicate that grab sampling in naturally ventilated places may overestimate or underestimate the IAQ due to the inhomogeneous composition of indoor air caused by irregular exchanges with the outdoor air according to the season and/or occupants' habits.

Implications Seasonal and diurnal variations of VOCs, PM_2.5, bioaerosols in house, office, and schools were observed, in which PM_2.5 and bioaeorosols showed marked both intra- and interday variability, but VOCs did not. VOC-containing products were the most common source of air pollutants affecting the indoor air quality. External factors affecting the indoor air quality were season and indirectly ventilation. A grab sample cannot be representative in evaluating the air quality of a naturally ventilated environment precisely.     

Pilot‐scale evaluation using bioaugmentation to enhance PCE dissolution at dover AFB national test site

An Interstate Technology and Regulatory Council (ITRC) forum was recently held that focused on six case studies in which bioremediation of dense nonaqueous‐phase liquids (DNAPLs) was performed; the objective was to demonstrate that there is credible evidence for bioremediation as a viable environmental remediation technology. The first two case studies from the forum have been previously published; this third case study involves a pilot‐scale demonstration that investigated the effects of biological activity on enhancing dissolution of an emplaced tetrachloroethene (PCE) DNAPL source. It used a controlled‐release test cell with PCE as the primary DNAPL in a porous media groundwater system. Both laboratory tests and a field‐scale pilot test demonstrated that bioaugmentation can stimulate complete dechlorination to a nontoxic end product and that the mass flux from a source zone increases when biological dehalorespiration activity is enhanced through nutrient (electron donor) addition and bioaugmentation. All project goals were met. Important achievements include demonstrating the ability to degrade a PCE DNAPL source to ethene and obtaining significant information on the impacts to the microbial populations and corresponding isotope enrichments during biodegradation of a source area. © 2007 Wiley Periodicals, Inc.     

Bioleaching of heavy metals from sewage sludge,direct action of Acidithiobacillus ferrooxidans or only the impact of pH?

Journal of Material Cycles and Waste Management - The bioleaching process comprises two mechanisms: direct action of the bacteria and indirect effect of low pH. In this work, the effect of bacteria...     

Screening for plants and rhizospheral fungi with bioremediation potency of petroleum-polluted soils in a Tehran oil refinery area

The contamination of soils by toxic and/or hazardous organic pollutants, especially with crude oil, is a widespread problem. This study was conducted in a petroleum-contaminated area in a Tehran oil refinery to find petroleum-resistant plants and their rhizospheral fungal strains with bioremediation potency. The plants growing in the oil-polluted area were collected and determined taxonomically. Root samples of the plant species were collected from a polluted area and fungal strains determined by laboratory methods and taxonomical keys. The growth ability of the isolated fungal strains was studied in media containing 1%–15% crude oil. Results showed that seven plant species were of the highest density in the contaminated area: Alhagi persarum, Hordeum marinum, Peganum harmala, Phragmites australis, Prosopis farcta, Salsola kali, and Senecio glaucus. The root-associated fungi were isolated and showed that the fungal variation in the oil-polluted area is higher than that in a non-polluted area. The growth assay of isolated fungal strains showed that all studied fungal strains were able to form colonies at the applied concentrations but Alternaria sp. and Rhizopus sp. were the most resistant ones. Some plants were resistant to oil pollution, which also had positive effects on the fungal strains.     

Using Design-Expert to Optimize the Properties of a Polyethersulfone Ultrafiltration Membrane Through the Incorporation of NH2-MIL-53(Fe) and PVP for Maximum Cr(VI) Removal and Flux

Journal of Polymers and the Environment - In this study, an NH2-MIL-53(Fe) functionalized membrane was fabricated for Cr(VI) removal from contaminated groundwater. Design-Expert was employed to...     

A risk-based decision making approach to determine fireproofing requirements against jet fires

API Publication 2218 is one of the most referred practices for fireproofing of onshore structural supports. Despite the extensive citation, it solely considers the effects of pool fire and rarely addresses jet fire outcomes. This absence of an explicit approach is common among all the other major references. Therefore, the basic objective of this paper is to introduce a new approach for determination of the necessity for fireproofing of structural supports against jet fires. For this purpose, the flame geometry and duration of jet fires are simulated for different leak sizes in identified fire potential sources. Then, following a worst-case analysis, those structures that may be impinged by long enough flames are screened out and then characterized by maximum impingement duration for fireproofing purpose. Moreover, each structure is assigned by a failure rate to estimate the degree of vulnerability through a detailed risk assessment. In this regard a new explanatory term called Structure Failure Rate (SFR) is introduced. This approach also enables researchers to quantify the effect of other protective systems (fire and gas detection, emergency shut-down, depressurization and firewalls) on the level of required fireproofing.     

Large-scale disinfection of real swimming pool water by electro-oxidation

Swimming pool users are a source of various contaminants and microorganisms. Conventional chlorine-based reagents treatment is commonly used to disinfect water. However, this disinfection treatment has serious serious health issues such as formation of carcinogenic by-products, i.e., trihalomethanes. In order to prevent this problem, an electrochemical disinfection process was carried out using synthetic and real swimming pool waters. The performance of the electrochemical system was evaluated by studying the effect of current intensity (0.5–3.0 A), treatment time, type of anode (Nb/BDD and Ti/Pt) and the initial concentration of pathogens Escherichia coli and P. aeruginosa. Results show that real swimming pool water, initially containing 10⁶ CFU/100 mL of pathogens, was disinfected at current intensities of 1.5 and 3.0 A using, respectively, Nb/BDD and Ti/Pt as anode materials (CFU: colony-forming units, BDD: boron-doped diamond). This work is also one of the few showing the up-scaling of electrochemical disinfection of real swimming pool water at large volumes of 100 L.     

Enhanced reductive dechlorination of PCE in unconsolidated soils

An Interstate Technology and Regulatory Council (ITRC) forum was recently held that focused on six case studies in which bioremediation of dense nonaqueous phase liquids (DNAPLs) was performed. The objective was to demonstrate that there is credible evidence for bioremediation as a viable environmental remediation technology. A discussion of the first case study from the ITRC forum was published in the previous issue of Remediation. This article presents a discussion of the second case study, which involves enhanced reductive dechlorination (ERD) of tetrachloroethene (PCE) in unconsolidated soils—primarily silts and clays with very low permeabilities. The project results indicate that complete reductive dechlorination was achieved and provide encouragement that large amounts of nonaqueous solvent can be brought into the reductive dechlorination treatment process by dissolution and desorption, giving support to the contention that the capacity to attack nonaqueous mass is a prerequisite for any effective treatment of DNAPL source zones. The site geology for this project was relatively unfavorable, and further work is needed to confirm that the ERD technology can economically reach a natural attenuation endpoint for this type of setting. © 2006 Wiley Periodicals, Inc.     

Devulcanization of Ground Tires by Different Strains of Bacteria: Optimization of Culture Condition by Taguchi Method

Biological devulcanization of ground tires (GTs) was evaluated by eleven different bacteria belonging to the genera Thiobacillus, Gordonia, Nocardia, Amycolaptopsis and Pseudomonas. The GTs were treated by each bacterium in a mineral medium and devulcanization was measured by increasing the sulfate of the medium and decreasing the sulfur of the GTs. The effects of incubation time (10 and 20 days) and the percent of ground tire in the medium (0.5 and 5 w/v %) on desulfurization were investigated. No significant changes were observed after 10 days of incubation. The total sulfur contents of all bio-treated GTs were decreased by 6–21% in 0.5% GTs after 20 days of incubation. While in 5% GTs, the total sulfur contents were mainly decreased using Thiobacillus ferroxidans DSMZ 583 and PTCC 1647 up to 27 and 15%, respectively. SEM photograph further indicated a good coherency interface between the bacteria and the GTs. Subsequently, Taguchi method was applied for the optimization of the culture condition of DSMZ 583. An L12 orthogonal array was performed by which the effects of eleven factors in two levels were evaluated. It was found that the amount and mesh size of GTs are the most important factors in biological devulcanization of ground tires.