Effects of Cu2+ and humic acids on degradation and fate of TBBPA in pure culture of Pseudomonas sp. strain CDT

Soil contamination with tetrabromobisphenol A(TBBPA) has caused great concerns;however, the presence of heavy metals and soil organic matter on the biodegradation of TBBPA is still unclear. We isolated Pseudomonas sp. strain CDT, a TBBPA-degrading bacterium, from activated sludge and incubated it with ~(14)C-labeled TBBPA for 87 days in the absence and presence of Cu~(2+)and humic acids(HA). TBBPA was degraded to organic-solvent extractable(59.4% ± 2.2%) and non-extractable(25.1% ± 1.3%) metabolites,mineralized to CO_2(4.8% ± 0.8%), and assimilated into cells(10.6% ± 0.9%) at the end of incubation. When Cu~(2+)was present, the transformation of extractable metabolites into non-extractable metabolites and mineralization were inhibited, possibly due to the toxicity of Cu~(2+)to cells. HA significantly inhibited both dissipation and mineralization of TBBPA and altered the fate of TBBPA in the culture by formation of HA-bound residues that amounted to 22.1% ± 3.7% of the transformed TBBPA. The inhibition from HA was attributed to adsorption of TBBPA and formation of bound residues with HA via reaction of reactive metabolites with HA molecules, which decreased bioavailability of TBBPA and metabolites in the culture. When Cu~(2+)and HA were both present, Cu~(2+)significantly promoted the HA inhibition on TBBPA dissipation but not on metabolite degradation. The results provide insights into individual and interactive effects of Cu~(2+)and soil organic matter on the biotransformation of TBBPA and indicate that soil organic matter plays an essential role in determining the fate of organic pollutants in soil and mitigating heavy metal toxicity.     

Blowing policy bubbles: rethinking emissions targets and low-carbon energy policies in the U.K.

The issue of proportionality is central to climate policy debates about setting targets for the reduction of greenhouse gas emissions and the development of low-carbon energy. In effect, these debates centre on whether the perceived social costs outweigh the benefits of policies and, if not, whether this may lead to over-investment or ‘policy bubbles’. Political attention, agenda setting and policy image are all crucial drivers of ambitious policy formation, as seen in the case of the United Kingdom's (U.K.) Climate Change Act (2008). However, as political salience waned and economic depression dragged on, the cost of long-term climate targets has been reconsidered. Based on documentary analysis and 33 interviews with central political actors, this article presents a detailed account of how economic arguments have been used to reinterpret and challenge policies, using the heuristics of ‘over-investment’ and ‘policy bubbles’. Ultimately, arguments about proportionality hinge on which costs and benefits are considered. In the U.K., economic and technical framings are typically prioritised, but they do not explain contradictory and politically motivated policy decisions. We discuss these dynamics within the context of maturing renewable energy technologies, high energy prices and the U.K.’s cross-party consensus approach to climate politics.     

Influence of the oxide content on the ignition energies of aluminium powders

Some results of determination of ignition energies for an aluminium powder with various oxide contents are presented. Common use of processes like high-speed cutting produce explosive dust clouds, so that we focused this study on hazard of metallic powders. An industrial aluminium powder has been used for this work. An original process, based on the principle of electrochemical anodisation, has been developed to increase, under control, the oxide coating of particles.

The sensitivity study to spark ignition was performed in an Hartmann explosion tube of 1.3L. The Langlie test method was applied to evaluate the energies leading to a probability of ignition of 50% (E₅₀) of the selected samples. The results confirm that the ignition energies increase with the oxide content of the powder.     

Tradescantia micronucleus test indicates genotoxic potential of traffic emissions in European cities

Urban atmospheres contain complex mixtures of air pollutants including mutagenic and carcinogenic substances such as benzene, diesel soot, heavy metals and polycyclic aromatic hydrocarbons. In the frame of a European network for the assessment of air quality by the use of bioindicator plants, the Tradescantia micronucleus (Trad-MCN) test was applied to examine the genotoxicity of urban air pollution. Cuttings of Tradescantia clone #4430 were exposed to ambient air at 65 monitoring sites in 10 conurbations employing a standardised methodology. The tests revealed an elevated genotoxic potential mainly at those urban sites which were exposed to severe car traffic emissions. This bioassay proved to be a suitable tool to detect local 'hot spots' of mutagenic air pollution in urban areas. For its use in routine monitoring programmes, however, further standardisation of cultivation and exposure techniques is recommended in order to reduce the variability of results due to varying environmental conditions.     

Ozone pollution and ozone biomonitoring in European cities. Part I: Ozone concentrations and cumulative exposure indices at urban and suburban sites

In the frame of a European research project on air quality in urban agglomerations, data on ozone concentrations from 23 automated urban and suburban monitoring stations in 11 cities from seven countries were analysed and evaluated. Daily and summer mean and maximum concentrations were computed based on hourly mean values, and cumulative ozone exposure indices (Accumulated exposure Over a Threshold of 40 ppb (AOT40), AOT20) were calculated. The diurnal profiles showed a characteristic pattern in most city centres, with minimum values in the early morning hours, a strong rise during the morning, peak concentrations in the afternoon, and a decline during the night. The widest amplitudes between minimum and maximum values were found in central and southern European cities such as Düsseldorf, Verona, Klagenfurt, Lyon or Barcelona. In the northern European cities of Edinburgh and Copenhagen, by contrast, maximum values were lower and diurnal variation was much smaller. Based on ozone concentrations as well as on cumulative exposure indices, a clear north–south gradient in ozone pollution, with increasing levels from northern and northwestern sites to central and southern European sites, was observed. Only the Spanish cities did not fit this pattern; there, ozone levels were again lower than in central European cities, probably due to the direct influence of strong car traffic emissions. In general, ozone concentrations and cumulative exposure were significantly higher at suburban sites than at urban and traffic-exposed sites. When applying the newly established European Union (EU) Directive on ozone pollution in ambient air, it was demonstrated that the target value for the protection of human health was regularly surpassed at urban as well as suburban sites, particularly in cities in Austria, France, northern Italy and southern Germany. European target values and long-term objectives for the protection of vegetation expressed as AOT40 were also exceeded at many monitoring sites.     

MIE determination and thermal degradation study of PA12 polymer powder used for laser sintering

Pulverized materials such as metallic or polymer powders play a considerable role in many industrial processes. Their use requires the introduction of preventive safeguards to control the plant's safety.PA12 polymer powder processing by laser sintering is characteristic of this tendency. The present work concerns PA12 powder (bimodal particle size distribution: 10 μm and 55 μm) and relates to explosion sensitivity and the thermal degradation of this powder, which can occur during laser sintering. Minimum Ignition Energy is determined using a modified Hartmann tube combined with the Langlie method developed in the PRISME Laboratory. This study shows the influence of parameters such as distance between the electrodes, powder concentration and arc power on MIE values. Theses parameters vary in the range of 3–6 A for the current intensity of the spark and the electrode gap in the range of 2.5–4 mm. The MIE is obtained for a spark gap of 3 mm and current intensity of the 4 A spark in our device. It shows that the MIE is less than 40 mJ for concentrations approaching 1000 g/m³. At lower concentrations (under 150 g/m³) the MIE increases but discrepancies in measurements appear, probably because of the static electricity that creates strong irregularities in dust dispersion. The second part of this study concerns the thermal degradation of the PA12 which is performed by thermogravimetric experiments coupled with mass spectrometric (MS) analysis for gas investigation. The mass loss measurement combined with the gas analysis allows the principal stages of degradation to be determined so as to calculate the kinetics parameter PA12. Experiments have been performed for different heating rates between 1 and 30 K min^?1 and the reproducibility of experiments has been verified. The activation energy is determined using two methods: Freidman and KAS. For a reaction rate of between 0.2 and 0.6, the activation energy is nearly constant. The KAS method gives a value of E_a = 250 kJ mol^?1 and the Friedman method gives E_a = 300 kJ mol^?1. The gas analysis by MS shows that oxidation begins at over 350 °C and finishes at under 650 °C with the formation of CO₂ and H₂O. Other major peaks with an m/z ratio of 29, 28 and 30 are noticed in this range of temperature. They show the presence of intermediate species such as C₂H₆, NO or CH₂O. The presence of HCN is also detected (m/z ratio of 27).     

Effect of quasi-static prestrain on the formability of dual phase steels in electrohydraulic forming

Dual phase steels derive their name from their microstructure, which consists of islands of martensite surrounded by a ferrite matrix. These steels are increasingly being used in automobile structures in order to reduce weight, improve fuel economy, and maintain crash safety performance. The higher strength grades of dual phase steels, such as DP780 and DP980, often present significant formability challenges in sheet stamping operations, and therefore any technologies which could alleviate these issues would be of significant value to the automotive industry. Electrohydraulic forming (EHF) is based upon the electro-hydraulic effect: a complex phenomenon related to the discharge of high voltage electrical current through a liquid. In EHF, electrical energy is stored in a bank of capacitors and is converted into the kinetic energy needed to form sheet metal by rapidly discharging that energy across a pair of electrodes submerged in a fluid. During such a discharge, a high pressure, high temperature plasma channel is created between the tips of the electrodes. The resulting shockwave in the liquid, initiated by the expansion of the plasma channel, is propagated toward the blank at the acoustic velocity of the fluid, and the mass and momentum of the water in the shock wave accelerates the sheet metal blank toward the die. The objective of this paper is to report the results of formability testing of dual phase steels under three basic conditions: (1) conventional limiting dome height (LDH) testing; (2) starting with a flat blank and using one pulse of EHF to fill the desired die geometry; and (3) starting with a quasi-static preforming step to partially fill the die cavity and then using one pulse of EHF to fill the remaining area of the die cavity. A hybrid process which combines sheet hydroforming (HF) and EHF as described herein has the potential to reduce the cycle time of the EHF process by replacing the initial EHF forming increments with one quasi-static preforming step. Additionally, a numerical model was developed and employed in order to better understand the sheet deformation process within EHF. The numerical model consists of four distinct models that are integrated into one: (1) an electrical model of the discharge channel, (2) a model of the plasma, (3) a model of the liquid as a pressure-transmitting medium, and (4) a deformable sheet metal blank in contact with a rigid die. Significant improvements in formability were confirmed experimentally for DP780 and DP980 by forming into conical and v-shape dies using EHF from a flat sheet and by using EHF combined with a quasi-static preforming step. Numerical modeling showed that the peak strain rates occurring in both single-pulse EHF the hybrid HF-EHF process are approximately 17,000 units per second.