The continuous increase in waste generation warrants global management of waste to reduce the adverse economic, social, and environmental impact of waste while achieving goals for sustainability. The complexity of waste management systems due to different waste management practices renders such systems difficult to analyze. System dynamics (SD) approach aids in conceptualizing and analyzing the structure, interactions, and mode of behavior of the complex systems. The impact of the underlying components can therefore be assessed in an integrated way while the impact of possible policies on the system can be studied to implement appropriate decisions. This review summarizes various applications of SD pertinent to the waste management practices in different countries. Practices may include waste generation, reduction, reuse/recovery, recycling, and disposal. Each study supports regional-demanding targets in environmental, social, and economic scopes such as expanding landfill life span, implementing proper disposal fee, global warming mitigation, energy generation/saving, etc. The interacting variables in the WMS are specifically determined based on the defined problem, ultimate goal, and the type of waste. Generally, population and gross domestic product can increase the waste generation. An increase in waste reduction, source separation, and recycling rate could decrease the environmental impact, but it is not necessarily profitable from an economic perspective. Incentives to separate waste and knowledge about waste management are variables that always have a positive impact on the entire system.
Environmental Science and Pollution Research - Trace copper ion (Cu(II)) in water and wastewater can trigger peroxymonosulfate (PMS) activation to oxidize organic compounds, but it only works under... 相似文献
Environmental Science and Pollution Research - Three sequential extraction procedures (SEPs), modified Tessier, modified BCR, and CIEMAT, were compared for mercury fractionation in polluted soils.... 相似文献
ABSTRACT In this study, a three-dimension (3D) computational model was proposed to investigate the flow and heat transfer characteristics of the intake grilles of two different fuel cell vehicles. The models of the intake grilles were constructed according to the actual sizes of two vehicles, namely, Roewe 950 and Toyota Mirai, considering the heat dissipation unit to simplify the heat transfer model of the vehicle. The results showed that relative to Roewe 950, Mirai intake air flow rate was approximately 10% higher, the heat transfer capacity was approximately 7% higher, and the intake grille area was larger. The coolant outlet temperature of Mirai was lower than that of Roewe 950, which was beneficial for the long term and stable operation of a fuel cell. This comparative study provided guidance for the intake grille and radiator design of fuel cell vehicles. The only difference between fuel cell vehicles on the market and conventional vehicles was that in the former, the internal combustion engine was replaced with a fuel cell stack, which had insufficient heat transfer capacity because of the reducing temperature difference. Increasing the intake grille area and the heat exchange capacity of the radiator were the key issues for the development of fuel cell vehicles. In this study, an optimal window opening angle of the radiator fin of 23° provided a maximal heat transfer coefficient. 相似文献
In this study, MnO2 and pyrolusite were used as the catalysts to prepare modified activated carbon, that is, AC-Mn and AC-P, respectively, from coals by blending method and steam activation. The Brunauer–Emmett–Teller (BET) results indicated that the AC-P had higher surface areas and micropore volumes than the AC-Mn with the same blending ratio. The relative contents of basic functional groups (i.e., C = O, π-π*) on AC-P were slightly lower than those on AC-Mn, while both contained the same main metal species, namely, MnO. The desulfurization results showed that with 3 wt% of blending ratio, AC-Mn3 and AC-P3 had higher sulfur capacities at 220 and 205 mg/g, respectively, which were much higher than for the blank one (149.6 mg/g). Moreover, the AC-P had relatively higher sulfur capacity than the AC-Mn with the same contents of Mn, which might be attributed to the existence of other metals in pyrolusite. After the desulfurization process, MnO were gradually transferred into MnSO4, and the relative contents of basic functional groups decreased evidently for both AC-Mn3 and AC-P3. The results demonstrated that pyrolusite could be one good alternative to MnO2 to prepare modified activated carbon for desulfurization.
Implications: MnO2 and pyrolusite were used as the additives to prepare modified activated carbon from coals by a blending method and by steam activation, that is, AC-Mn and AC-P, respectively. The AC-P had higher surface areas and micropore volumes than the AC-Mn with the same blending ratio. The AC-Mn and AC-P had higher sulfur capacities than a blank one. Moreover, the AC-P had relatively higher sulfur capacity than the AC-Mn with the same contents of Mn. The results demonstrated that pyrolusite could be one good alternative to MnO2 to prepare modified activated carbon for desulfurizatio. 相似文献