Special issue on contamination,remediation and health for pollutants in natural aquatic,soil, sediments and atmospheric environments

Environmental Geochemistry and Health -     

Induction of cytochrome P4501A and endocrine disrupting effects of school incinerator residues

The emission of the dioxin-like compounds from on-site waste incinerators of seven schools in Kyonggi Province of Korea was evaluated by determination of the cytochrome P4501A(CYP1A) catalytic activity and antiestrogenic activity using cell culturemicrobioassay. The residue samples were extracted in a Soxhlet apparatus using toluene for 20 hr. The concentrated crude extractswere fractionated with a basic alumina column. Dioxin-like compounds were then extracted. Induction of CYP1A activity in a rat(H4IIE) hepatoma cell line was used as indicator of biologicaleffect of incinerator residues and measured as 7-ethoxyresorufin-O-deethylase(EROD) activities. The EROD activities of fraction II extracts (one of the two extracts) in the H4IIE cells were from 0.044±0.002 to 4.424±0.351 ng-TEQ g^-1 (TCDD Toxicity equivalent), showing relatively high inducing capacity. Antisetrogenicity of the extracts was measured as decrease in E₂-induced cell proliferation. Most of the extracts showed antiestrogenic activity in MCF7-BUS cell.The TEQ levels of the incinerator residues and the antiestrogenicactivities were in good correlation, strongly suggesting that thepotent toxic emissions were indeed produced from the on-site school waste semi-incinerators and could cause the antiestrogenicity.     

LIDAR Measurements of the Vertical Aerosol Profile and Optical Depth during the ACE-Asia 2001 IOP, at Gosan, Jeju Island, Korea

In order to investigate the characteristic of optical properties of Asian dust particles, the atmospheric aerosol vertical profile was measured with the multi-wavelength LIDAR system, at the Gosan super site (33 degrees 17'N, 126 degrees 10'E) in Jeju Island, Korea, during the ACE-Asia intensive observation period, 11 March-4 May 2001. An air mass backward trajectory analysis, using Hysplit-4, was carried out to track the aerosol plume, with high mass loading, from the Chinese desert regions during the period of Asian dust storm events. Vertical atmospheric aerosol profiles on three major Asian dust storm event days, 22 March and 13 and 26 April 2001, have been analyzed. The LIDAR-derived aerosol optical depth values were compared with those measured by a collocated sunphotometer.     

Quality control for coal combustion products in South Korea through assessed pozzolanic-activity index with long-term property tests

In South Korea, nine million tons of fly ash (FA) are annually produced and approximately 70 % is reutilized for industrial demand. For the prompt reuse and insufficient reclamation site, quality control of FA which is main productive construction material from coal ash is very important. Assessed Pozzolanic-activity Index (API) test which needs only 2 days for evaluation of pozzolanic reaction is currently considered as an alternative of activity index measurement. This paper aims for an applicability of API test for prompt quality control and investigation of domestic FA properties. For the work, FAs from two different power plant types are prepared, and quality tests are carried out based on Korean Standards (KS) methods and API method. Lots of test results are compared with those from API and K-value test for FA with age of 7 days–1 year. From the test results for FA aged 1 year, API results are evaluated to be closely related with those from activity index and K-value, and the correlations are improved with increasing ages regardless of plant types. The applicability of API test is verified and the reduced period of FA quality evaluation can accelerate prompt use and the related process of FA.     

Trace elements in surface sediments of the Hooghly (Ganges) estuary: distribution and contamination risk assessment

Our objective was to evaluate distribution and accumulation of trace elements (TEs) in surface sediments along the Hooghly (Ganges) River Estuary, India, and to assess the potential risk with view to human health. The TE concentrations (mg kg^?1 dry weight) exhibited a wide range in the following order: Al (31.801 ± 15.943) > Fe (23.337 ± 7584) > Mn (461 ± 147) > S (381 ± 235) > Zn (54 ± 18) > V (43 ± 14) > Cr (39 ± 15) > As (34 ± 15) > Cu (27 ± 11) > Ni (24 ± 9) > Se (17 ± 8) > Co (11 ± 3) > Mo (10 ± 2) > Hg (0.02 ± 0.01). Clay, silt, iron, manganese and sulphur were important for the accumulation of TE in the sediments as confirmed by factor analysis and Pearson correlation. The accumulation and dispersal of TEs were most likely to be governed by both tide-induced processes and anthropogenic inputs from point and non-point sources. Enrichment factor analysis and geoaccumulation index revealed serious contamination of the sediments with Se and As, while comparing the consensus-based sediment quality guidelines (SQGs), adverse biological effects to benthic fauna might be caused by As, Cu, Ni and Cr. This investigation may serve as a model study and recommends continuous monitoring of As, Se, Cu, Ni and Cr to ascertain that SQGs with respect to acceptable levels of TEs to safeguard geochemical health and ecology in the vicinity of this estuary.     

A study on the reaction characteristics of vanadium-impregnated natural manganese oxide in ammonia selective catalytic reduction

This study investigated the effect of adding vanadium (V) to natural manganese oxide (NMO) in ammonia (NH3) selective catalytic reduction (SCR). The addition of V to NMO decreased the catalytic activity at low temperatures by blocking the active site. However, the enhancement of catalytic activity was achieved by controlling NH3 oxidation at high temperatures. From the NH3 temperature programmed desorption and oxygen on/off test, it was confirmed that the amount of Lewis acid site and active lattice oxygen of the catalyst affects the catalytic performance at low temperature.     

A comparison study on high-temperature water–gas shift reaction over Fe/Al/Cu and Fe/Al/Ni catalysts using simulated waste-derived synthesis gas

A comparative study on Fe/Al, Fe/Al/Cu, and Fe/Al/Ni catalysts in high-temperature water–gas shift reaction (HT–WGS) using simulated waste-derived synthesis gas has been carried out. The metal oxide (Cu and Ni) and aluminum incorporated Fe catalysts were designed to get highly active HT–WGS catalysts. Despite the high CO concentration in the simulated waste-derived synthesis gas, Fe/Al/Cu catalyst exhibited the highest CO conversion (84 %) and 100 % selectivity to CO₂ at a very high gas hourly space velocity (GHSV) of 40,057 h^?1. The outstanding catalytic performance is mainly due to easier reducibility, the synergy effect of Cu and Al, and the stability of the magnetite.     

Tool wear of coated drills in drilling CFRP

This study aimed to investigate the wear of certain coated drills when drilling carbon fiber reinforced composites (CFRP). Three different drills were used in the drilling experiments: uncoated, diamond coated and AlTiN coated carbide (WC–Co) drills. The tool wear in CFRP machining was quite different from that in conventional metal machining. The primary wear type was a dulling or blunting of the cutting edge, which has been referred to as edge rounding wear or edge recession. In this paper, a hypothesis has been developed to explain the edge rounding wear in CFRP machining. Due to the fracture-based chip formation of CFRP, there is lack of the work material stagnation zone in front of the cutting edge, which normally prevents the edge wear in metal machining. Series of wear lead to rapid dulling of the cutting edge. The resistance to edge rounding wear on the coated as well as uncoated drills has been investigated. The diamond coating significantly reduces the edge rounding wear. However, AlTiN coated drills showed no visible improvement over the uncoated carbide drill, despite of their high hardness, thus not protecting the drill. The wear mechanisms of the uncoated carbide drill and coatings are discussed. It is believed that the 2-body and 3-body abrasive wear fail to explain the observed tool wear in CFRP drilling. However, the wear of the coatings and uncoated carbide substrate from tribo-meter tests correlated well with the tool wear in the CFRP drilling. Therefore, the tribo-meter test can be used to screen the prospective tool materials before carrying drilling experiment.     

Factors affecting the direct mineralization of CO2 with olivine

Olivine, one of the most abundant minerals existing in nature, is explored as a CO2 carbonation agent for direct carbonation of CO2 in flue gas. Olivine based CO2 capture is thermodynamically favorable and can form a stable carbonate for long-term storage. Experimental results have shown that water vapor plays an important role in improving CO2 carbonation rate and capacities. Other operation conditions including reaction temperature, initial CO2 concentration, residence time corresponding to the flow rate of CO2 gas stream, and water vapor concentration also considerably affect the performance of the technology.