The continuous increase in waste generation warrants global management of waste to reduce the adverse economic, social, and environmental impact of waste while achieving goals for sustainability. The complexity of waste management systems due to different waste management practices renders such systems difficult to analyze. System dynamics (SD) approach aids in conceptualizing and analyzing the structure, interactions, and mode of behavior of the complex systems. The impact of the underlying components can therefore be assessed in an integrated way while the impact of possible policies on the system can be studied to implement appropriate decisions. This review summarizes various applications of SD pertinent to the waste management practices in different countries. Practices may include waste generation, reduction, reuse/recovery, recycling, and disposal. Each study supports regional-demanding targets in environmental, social, and economic scopes such as expanding landfill life span, implementing proper disposal fee, global warming mitigation, energy generation/saving, etc. The interacting variables in the WMS are specifically determined based on the defined problem, ultimate goal, and the type of waste. Generally, population and gross domestic product can increase the waste generation. An increase in waste reduction, source separation, and recycling rate could decrease the environmental impact, but it is not necessarily profitable from an economic perspective. Incentives to separate waste and knowledge about waste management are variables that always have a positive impact on the entire system.
Boro rice, an emerging low-risk crop variety of rice, cultivated using residual or stored water after Kharif season. To enhance the quality and production of rice, potassium (K) and phosphorus (P) are the common constituents of agricultural fertilizers. However, excess application of fertilizers causes leaching of nutrients and contaminates the groundwater system. Therefore, assessment and optimization of fertilizer dose are needed for better management of fertilizers. Towards this, the present study determines the path, persistence, and mobility of K and P under the Boro rice cropping system. The experimental site consisted of four plots having Boro rice with four different fertilizer doses of nitrogen (N), P, K viz. 100%, 75%, 50%, and 25% of the recommended dose. Disturbed soil samples were analysed for K and P from pre-sown land to tillering stage at 0–5, 5–10, 10–15, 15–30, 30–45, and 45–60 cm depths. Simultaneously, K and available P were also simulated in the subsurface soil layers through the HYDRUS-1D model. The statistical comparisons were made with RMSER, E, and PBIAS between the modelled values and laboratory-measured values. Although, the results showed that all the treatments considered had agreeable simulations for both K and P, the K simulations were found to be better as compared to P simulations except for 25% where P simulations outperformed K. The simulated concentration at all doses was found most appropriate when measured for the subsurface layers (up to 45 cm), while showed an underestimation in the bottom layers (45–60 cm) of soil.
Environmental Science and Pollution Research - Trace copper ion (Cu(II)) in water and wastewater can trigger peroxymonosulfate (PMS) activation to oxidize organic compounds, but it only works under... 相似文献
This paper investigates the effects of the incorporation of lignin and small quantities of epoxidized natural rubber (ENR) as an impact modifying agent on blends of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) and poly(ε-caprolactone) (PCL). The addition of lignin resulted in a slight improvement of flexural strength and modulus of the ternary blending system. Incorporation of ENR into the blend resulted in an increase in notched Izod impact strength from 40 to 135% depending on the concentration of ENR. The addition of lignin into the blend resulted in an improvement of thermal stability of the ternary blend system. Morphological analysis showed a good dispersion of PHBV phases and lignin within the PCL matrix. Rheological characterization revealed that the presence of lignin resulted in increased storage modulus of the bioblend. 相似文献
Environmental Science and Pollution Research - Three sequential extraction procedures (SEPs), modified Tessier, modified BCR, and CIEMAT, were compared for mercury fractionation in polluted soils.... 相似文献
ABSTRACT In this study, a three-dimension (3D) computational model was proposed to investigate the flow and heat transfer characteristics of the intake grilles of two different fuel cell vehicles. The models of the intake grilles were constructed according to the actual sizes of two vehicles, namely, Roewe 950 and Toyota Mirai, considering the heat dissipation unit to simplify the heat transfer model of the vehicle. The results showed that relative to Roewe 950, Mirai intake air flow rate was approximately 10% higher, the heat transfer capacity was approximately 7% higher, and the intake grille area was larger. The coolant outlet temperature of Mirai was lower than that of Roewe 950, which was beneficial for the long term and stable operation of a fuel cell. This comparative study provided guidance for the intake grille and radiator design of fuel cell vehicles. The only difference between fuel cell vehicles on the market and conventional vehicles was that in the former, the internal combustion engine was replaced with a fuel cell stack, which had insufficient heat transfer capacity because of the reducing temperature difference. Increasing the intake grille area and the heat exchange capacity of the radiator were the key issues for the development of fuel cell vehicles. In this study, an optimal window opening angle of the radiator fin of 23° provided a maximal heat transfer coefficient. 相似文献