Quality of water used during cage cultivation of rainbow trout (Oncorhynchus mykiss) in Bereket HES IV Dam Lake (Muğla,Turkey)

A thorough investigation of the impact of rainbow trout (Oncorhynchus mykiss) cultivation on surface water quality in the area known as Bereket HES IV Dam Lake was conducted. Water samples were collected from October 2009 to June 2010 from four stations in the Dam Lake and analyzed for water temperature, pH, dissolved oxygen, electrical conductivity, nitrite nitrogen, nitrate nitrogen, and orthophosphate. Surface water quality was then evaluated based on the comparison of samples collected from three stations located near fish cages to those collected from a reference station outside the cultivation area as well as by the comparison with standards specified in the Water Pollution Registration Act. According to the Water Pollution Registration Act, the surface water quality of the Dam Lake was class I. Additionally, there were no significant differences in water quality within the Dam Lake among any of the sampling stations, including the reference station. Overall, these findings indicate that cage cultivation of rainbow trout may have a negative impact on the entire Dam Lake.     

Fungal flora in indoor and outdoor air of different residential houses in Tekirdag City (Turkey): Seasonal distribution and relationship with climatic factors

This study was investigated the density and monthly distribution of indoor and outdoor microfungi in six different residential houses in Tekirdag City through the exposure of Petri dishes containing Rose-Bengal Streptomycin Agar media. Samples were collected in 1-month intervals over a period of 12 months between March, 2001, and February, 2002. We used 432 Petri dishes and counted a total of 4,205 microfungi colonies, 1,790 from indoor air and 2,415 from outdoor air. As a result, 42 species belonging to 12 genera were identified. The most frequent fungal genera were Penicillium (28.61%), Cladosporium (16.08%) and Alternaria (15.98%). While Penicillium (40.61%) and Cladosporium (15.92%) were the dominant genera of indoor air, Alternaria (20.62%) and Penicillium (19.71%) were isolated most frequently from outdoor air (Table 3). Alternaria citri (10.15%) and Penicillium brevicompactum (10.15%) were found to be the most frequent among the 42 identified species. While P. brevicompactum (19.55%) and Aspergillus niger (6.37%) were the most frequent indoor species, A. citri (13.37%) and Cladosporium cladosporioides (8.20%) were the most frequent outdoor species. Linear Regression Analysis was applied to determine whether or not there was a relationship between the number of colonies of isolated fungal genera and meteorological factors during the research period. Correlations between the presence of Aspergillus and temperature, relative humidity, duration of sunny periods and agents of air pollution such as SO(2) and PM were statistically significant. No significant correlations, however, were found between other fungal genera and environmental variables.     

Part based process performance monitoring (PbPPM)

The performances of completed manufacturing processes were evaluated using the surface response to excitation (SuRE) and Lamb wave methods. Both methods used the same piezoelectric elements attached to the surface of the workpiece. The SuRE method and the Lamb wave method were used to identify the structural changes created by welding, drilling, coating, filling a slot with glue, and composite patching. This study indicates that the tested methods are feasible for part based process performance monitoring (PbPPM) which evaluates the quality of the completed process with the sensors attached to the workpiece.     

Preparation, Thermal Properties and Thermal Reliability of Form-Stable Paraffin/Polypropylene Composite for Thermal Energy Storage

This study is focused on the preparation, characterization, and determination of thermal properties and thermal reliability of paraffin/polypropylene (PP) composite as a novel form-stable phase change material (PCM) for thermal energy storage applications. In the composite, paraffin acts as a PCM when PP is operated as supporting material. The composites prepared at different mass fractions of paraffin (50, 60, 70, 80, and 90 w/w%) by solution casting method were subjected to leakage test by heating the composites over the melting temperature of the PCM. The paraffin/PP composite (70/30 w/w%) is found as the maximum paraffin containing composite and was characterized using Fourier transform infrared spectroscopy, optic microscopy, differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA) techniques. DSC analysis indicated that the form-stable paraffin/PP composite melts at 44.77–45.52 °C and crystallizes at 53.55–54.80 °C. It has latent heats of 136.16 and −136.59 J/g for melting and crystallization, respectively. These thermal properties make it potential PCM for latent heat thermal energy storage (LHTES) purposes such as solar space heating applications. Accelerated thermal cycling tests indicated that the form-stable PCM had good thermal reliability. TGA also showed that the form-stable PCM degrades in two distinguishable steps and had good chemical stability.     

Assessment of natural radiation exposure levels and mass attenuation coefficients of lime and gypsum samples used in Turkey

The activity concentrations of ²²⁶Ra, ²³²Th, and ⁴⁰K in lime and gypsum samples used as building materials in Turkey were measured using gamma spectrometry. The mean activity concentrations of ²²⁶Ra, ²³²Th, and ⁴⁰K were found to be 38 ± 16, 20 ± 9, and 156 ± 54 Bq kg^???1 for lime and found to be 17 ± 6, 13 ± 5, and 429 ± 24 Bq kg^???1 for gypsum, respectively. The radiological hazards due to the natural radioactivity in the samples were inferred from calculations of radium equivalent activities (Ra_eq), indoor absorbed dose rate in the air, the annual effective dose, and gamma and alpha indices. These radiological parameters were evaluated and compared with the internationally recommended limits. The experimental mass attenuation coefficients (μ/ρ) of the samples were determined in the energy range 81–1,332 keV. The experimental mass attenuation coefficients were compared with theoretical values obtained using XCOM. It is found that the calculated values and the experimental results are in good agreement.     

A numerical study on the effects of EGR and spark timing to combustion characteristics and NOx emission of a GDI engine

EGR is one of the most significant strategies for reducing especially nitrogen oxides (NO_x) emissions from internal combustion engines. The thermal efficiency of spark ignition engines is lower than compression ignition engines because of its lower compression ratio. If the compression ratio is increased to obtain higher thermal efficiency, there may be a knocking tendency in spark ignition engines. EGR can be used in order to reduce NO_x emissions and avoid knocking phenomena at higher compression ratios. In-cylinder temperature at the end of combustion is decreased and heat capacity of fresh charge is increased when EGR applied. Besides EGR, spark timing is another significant parameter for reducing exhaust emissions such as nitrogen oxides, and unburned hydrocarbon (UHC). In this study the effects of EGR and spark timing on spark ignition engine were investigated numerically. KIVA codes were used in order to model combustion process. The combustion process has been modeled for a single cylinder, four stroke and gasoline direct injection (GDI) spark ignition engine. The results showed that in-cylinder pressure and heat release rate decrease as EGR ratio increase. In-cylinder pressure increases with the advancing of spark timing. Advancing spark timing increases the heat release rate and in-cylinder temperature. The simulation results also showed that EGR reduced exhaust gas temperature and NO_x emissions.     

Developing of a pricing model for Turkish lignite used in thermal plants

The objective of this paper is to develop a general pricing model for Turkish Lignite, which is mainly sold to thermal plants. This model will contribute to the development of coal mining within the scope of privatization efforts of the Turkish energy market. The paper consists of two stages. First, data of 10 thermal plants have been evaluated by using hedonic pricing analysis to determine influential price parameters. The results of hedonic regression analysis indicate the effect and importance of calorific value and electricity price on lignite prices. Second, a general coal-pricing model has been developed by taking into account the results of hedonic analysis. Comparison of the coal prices estimated by the developed pricing model and the coal prices obtained from thermal plants indicates an acceptable relation.     

Bleaching of chemithermomechanical pulp (CTMP) using environmentally friendly chemicals

Increasing environmental restrictions require a reduction in the use of chlorine-containing bleaching agents mainly chlorine gas. There are several approaches to this goal, including changes in the cooking process and the influent treatment. The aim of this study is to improve the physical and optical properties of chemithermomechanical pulp (CTMP) which has low brightness and strong tendency towards aging in chlorine-free bleaching sequences. For this reason, initially 7 different sets of single stage hydrogen peroxide bleaching operations were performed. After the analysis of the data obtained, the optimum bleaching conditions were as: H2O2 ratio on oven dry (o.d) raw material: 2%, NaOH ratio (on o.d raw material): 1.5%, MgSO4 ratio (on o.d raw material) : 0.5%, Na2SiO3 ratio (on o.d raw material) : 3%, EDTA ratio (on o.d raw material) : 0.5%, reaction time: 60 minutes, reaction temperature: 70 degrees C and concentration: 16%. Then, 11 different sets of two and multistage H2O2 (P), NaBH4 (B), and Na2S2O4 (S) bleaching operations were carried out. Optimum bleaching conditions were found in bleaching of BPSP with 4 stage sequences. As a result, CTMP brightness was observed to increase from 47% to 81.37% elrepho while yellowness of bleached pulps decreased from 321 per thousand to 164.01 per thousand elrepho.     

Investigation of seat belt use among the drivers of different education levels

Seat belt use habit has been investigated according to the education level of drivers. Copies of a questionnaire were distributed to 1000 participants of four different education levels. Factors such as seat belt usage habit, restricting factors and crash data have been investigated. Data have been analyzed with SPSS 15.0 software. Increased level of education leads to increased seat belt usage, lower numbers of crashes and crash severities. The factors restricting seat belt use are lack of habit, discomfort and short distance driving. The use of precaution signal and increases in comfort can increase seat belt usage. The primary and high school education on traffic safety and seat belt usage has been serving the purpose.