Use of coatings to minimise acid emissions during ceramic tile firing

The manufacture of traditional ceramic products (ceramic tiles, roof tiles, and bricks) is often associated with the emission of F, Cl, and S compounds during the firing stage. According to the literature, fluorine emissions can be reduced by adding CaCO₃ to the raw materials mixture used in fabricating these products. However, data available to the authors indicate that this procedure, which has been successfully applied in manufacturing structural ceramics (roof tiles and bricks), is ineffective in ceramic tile manufacture and modifies tile end properties.This paper examines the possibility of reducing such emissions by applying coatings of alkaline-earth carbonates on to the ceramic tile bottom surface to retain the acid compounds emitted during tile firing. The effectiveness of MgCO₃, CaCO₃, SrCO₃, and BaCO₃ coatings for retaining these acid emissions was studied, using the evolved gas analysis (EGA) technique with a TG-DSC-FTIR-QM instrument.The SrCO₃ coating was found to provide the greatest retention, showing that SO₂ and HCl were retained more efficiently than HF. The presence of fluorides, chlorides, and sulphates of Ca, Sr, and Ba was verified in the respective fired coatings, confirming the existence of chemical reactions between the emitted acid compounds and the coating materials at high temperature.     

Unexpected bias of freeze-drying on the performance assessment of chemical oxidation of soils contaminated by polychlorinated biphenyls

Environmental Chemistry Letters - Processes based on chemical oxidation are widely used for environmental remediation. Analysis of environmental samples such as soils often requires a freeze-drying...     

PM sources in a highly industrialised area in the process of implementing PM abatement technology. Quantification and evolution

Principal component analysis (PCA) coupled with a multilinear regression analysis (MLRA) was applied to PM(10) speciation data series (2002-2005) from four sampling sites in a highly industrialised area (ceramic production) in the process of implementing emission abatement technology. Five common factors with similar chemical profiles were identified at all the sites: mineral, regional background (influenced by the industrial estate located on the coast: an oil refinery and a power plant), sea spray, industrial 1 (manufacture and use of glaze components, including frit fusion) and road traffic. The contribution of the regional background differs slightly from site to site. The mineral factor, attributed to the sum of several sources (mainly the ceramic industry, but also with minor contributions from soil resuspension and African dust outbreaks) contributes between 9 and 11 microg m(-3) at all the sites. Source industrial 1 entails an increase in PM(10) levels between 4 and 5 microg m(-3) at the urban sites and 2 microg m(-3) at the suburban background site. However, after 2004, this source contributed less than 2 microg m(-3) at most sites, whereas the remaining sources did not show an upward or downward trend along the study period. This gradual decrease in the contribution of source industrial 1 coincides with the implementation of PM abatement technology in the frit fusion kilns of the area. This relationship enables us to assess the efficiency of the implementation of environmental technologies in terms of their impact on air quality.     

Assessment of the rangelands of southwestern Santiago del Estero, Argentina, for grazing management and research

Native rangelands of the southwest part of the province of Santiago del Estero, Argentina, are a key source of forage for cow-calf operations. The objectives of this study were to delineate the ecosystem units of the area, to describe the associated plant communities and to interpret the role that physical factors and disturbances such as fire and grazing have had in the changes of the structure of these plant communities. This information is needed for developing recommendations for grazing management, for prescribing appropriate improvement practices (e.g. shrub control, prescribed fire) and as guidelines for future research. The ecosystem was divided into smaller units using a hierarchical method, the categories of practical importance being 'range unit' and 'range site'. They represent the catchment and hillslope scale of the water runoff-runon phenomenon, respectively. Vegetation was sampled using a block and cluster sampling design, registering tree, shrub, forb and grass species frequency, and the standing aerial biomass of the herbaceous layer in a sampling unit=1 ha. Environmental data (topographic position, fire frequency, current and past use, and tree and shrub cover) were also registered for each sampling unit. Indirect ordination of sampling units classified according to range units and range sites, and correlation with environmental variables were performed using multidimensional scaling (MDS) as well as the vector fitting technique. Standing forage and stocking rate were estimated from biomass data. Results indicate that 'range site' is the ecosystem unit that should be considered for management purposes since it correlates well with plant communities: tall, hardwood forests are located on upland sites, woodlands are located on midland sites and savannas are located on lowland sites. Dense shrub thickets dominate in areas rated in poor condition, irrespective of range site. Disturbances such as fire and current and past use have a significant positive and negative correlation with range condition, respectively, suggesting that a state and transition model would explain vegetation dynamics better than the succession model. The estimated stocking rate in lowland sites in good condition was 2 ha UG(-1), while in upland sites in poor condition the stocking rate was 90 ha UG(-1). Active (fire, mechanical treatments) rather than passive (grazing management) methods should be used for range improvement in order to achieve the full potential of the ecosystem.     

Nickel(II) biosorption from aqueous solutions by shrimp head biomass

The present study evaluates the capacity of shrimp (Farfantepenaeus aztecus) head to remove toxic Ni(II) ions from aqueous solutions. Relevant parameters that could affect the biosorption process, such as shrimp head pretreatment, solution pH level, contact time and initial Ni(II) concentration, were studied in batch systems. An increase in Ni(II) biosorption capacity and a reduction in the time required to reach Ni(II) biosorption equilibrium was manifested by shrimp head biomass pretreated by boiling in 0.5 N NaOH for 15 min; this biomass was thereafter denominated APSH. The optimum biosorption level of Ni(II) ions onto APSH was observed at pH 7.0. Biosorption increased significantly with rising initial Ni(II) concentration. In terms of biosorption dynamics, the pseudo-second-order kinetic model described Ni(II) biosorption onto APSH best. The equilibrium data adequately fitted the Langmuir isotherm model within the studied Ni(II) ion concentration range. According to this isotherm model, the maximum Ni(II) biosorption capacity of APSH was 104.22 mg/g. Results indicate that APSH could be used as a low-cost, environmentally friendly, and promising biosorbent with high biosorption capacity to remove Ni(II) from aqueous solutions.     

Effect of ceramic industrial particulate emission control on key components of ambient PM10

The relationship between specific particulate emission control and ambient levels of some PM₁₀ components (Zn, As, Pb, Cs, Tl) was evaluated. To this end, the industrial area of Castellón (Eastern Spain) was selected, where around 40% of the EU glazed ceramic tiles and a high proportion of EU ceramic frits are produced. The PM₁₀ emissions from the ceramic processes were calculated over the period 2000–2006, taking into account the degree of implementation of corrective measures throughout the study period. Abatement systems were implemented in the majority of the fusion kilns for frit manufacture in the area as a result of the application of the Directive 1996/61/EC, leading to a marked decrease in PM₁₀ emissions. By contrast, emissions from tile manufacture remained relatively constant because of the few changes in the implementation of corrective measures. On the other hand, ambient PM₁₀ levels and composition measurements were carried out from 2002 to 2006. A high correlation between PM₁₀ emissions from frit manufacture and ambient levels of Zn, As, Pb and Cs (R² from 0.61 to 0.98) was observed. On the basis of these results, the potential impact of the implementation of corrective measures to reduce emissions from tile manufacture was quantified, resulting in a possible decrease of 3–5 μg/m³ and 2 μg/m³ in ambient mineral PM₁₀ (on an annual basis) in urban and suburban areas, respectively. This relatively simple methodology allows us to estimate the direct effect of a reduction in primary particulate emissions on ambient levels of key particulate components, and to make a preliminary quantification of the possibilities of air quality improvement by means of further emission reduction. Therefore, it is a useful tool for developing future air quality plans in the study area and in other industrialised areas.     

Inferring pollution records in sediment cores from transitional environments of Marquelia coast,Guerrero, Mexico

Environmental Science and Pollution Research - The vertical distribution pattern and concentrations of elements (Fe, Al, Ca, Mg, Mn, Cr, Cu, Ni, Co, Pb, Zn, and As) in the estuarine and lagoon...     

Effect of pH,ionic strength,and background electrolytes on Cr(VI) and total chromium removal by acorn shell of Quercus crassipes Humb. & Bonpl.

The ability of Quercus crassipes acorn shells (QCS) to remove Cr(VI) and total chromium from aqueous solutions was investigated as a function of the solution pH, ionic strength, and background electrolytes. It was found that Cr(VI) and total chromium removal by QCS depended strongly on the pH of the solution. Cr(VI) removal rate increased as the solution pH decreased. The optimum pH for total chromium removal varied depending on contact time. NaCl ionic strengths lower than 200 mM did not affect chromium removal. The presence of 20 mM monovalent cations and anions, and of divalent cations, slightly decreased the removal of Cr(VI) and total chromium by QCS; in contrast, divalent anions (SO₄ ^2?, PO₄ ^2?, CO₃ ^2?) significantly affected the removal of Cr(VI) and total chromium. The biosorption kinetics of chromium ions followed the pseudo-second-order model at all solution pH levels, NaCl ionic strengths and background electrolytes tested. Results suggest that QCS may be a potential low-cost biosorbent for the removal of Cr(VI) and total chromium from aqueous solutions containing various impurities.     

Long-term variability of metals from fungicides applied in amended young vineyard fields of La Rioja (Spain)

The long-term variability of total Cu content from fungicides applied in a certified wine region of Spain (La Rioja) and of other metals (Cd, Cr, Ni, Pb, and Zn) was evaluated in three young vineyard soils and subsoils unamended and amended with spent mushroom substrates (SMS) over a 3-year period (2006–2008). SMS is a promising agricultural residue as an amendment to increase the soil organic matter content but may modify the behaviour of metals from pesticide utilisation in vineyards. Fresh and composted SMS was applied each year at a rate of 25 t ha⁻¹ (dry-weight). Copper concentrations in the three unamended soils were 21.2–88.5, 25.5–77.1, and 29.4–78.4 mg kg⁻¹. They exceeded natural Cu concentrations of the region and reference sub-lethal hazardous concentration for soil organism. The concentrations of Cd, Ni, Pb, and Zn were largely below the sub-lethal limits. Thus, although Cu levels were lower than those of established vineyards, vine performance, and productivity might be affected. The variation in behaviour between different amendments for each soil was high, so a generic conclusion could not be drawn. The amendment practice seemed to have caused temporarily Cu mobilization respect to untreated soils. Total zinc concentrations fall within the range of the natural soil of La Rioja and were significantly affected (p < 0.05) especially by fresh state SMS addition, with increasing up to 75% respect to untreated specimen. The results indicated a build-up of fresh sites for metal retention at both surface and subsurface level, although no accumulation of metals was observed in the short-term period. However, the benefit for soils and the negative effects need to be monitored in the long run.