Effect of Common Chemical Treatments on the Process Kinetics and Mechanical Properties of Flax/Epoxy Composites Manufactured by Resin Infusion

Chemical treatments are widely employed to improve the fiber-matrix adhesion in composites based on eco-friendly fibers such as flax. To better understand the influence of these treatments on processing behavior, this study characterized the surface chemistry and morphology of woven flax fabrics treated by acetone, alkaline, silane and diluted epoxy. Flax/epoxy composites were then manufactured by resin infusion and the flow front and preform thickness evolution was monitored. The alkaline treatment was shown to result in a 50 % increase in equivalent permeability due to an increase in porosity which led to a decrease in flexural properties. The processing results were found to be in good agreement with predictions of a 1-dimensional model. This study suggests that infusion times are not considerably affected by the observed changes in surface energy. However, other implications of the treatments such as an increase in fibrillation can alter the infusion times significantly.

     

Singular air entrapment at vertical and horizontal supported jets: plunging jets versus hydraulic jumps

Environmental Fluid Mechanics - In plunging jets and at hydraulic jumps, large amounts of air bubbles are entrained at the impingement of the liquid jet into the receiving body. Air is entrapped...     

On the Environmental Efficiency of Water Storage: the Case of a Conjunctive use of Ground and Rainwater

Rainwater harvesting, consisting in collecting runoff from precipitation, has been widely developed to stop groundwater declines and even raise water tables. However, this expected environmental effect is not self-evident. We show in a simple setting that the success of this conjunctive use depends on whether the runoff rate is above a threshold value. Moreover, the bigger the storage capacity, the higher the runoff rate must be to obtain an environmentally efficient system. We also extend the model to include other hydrological parameters and ecological damages, which respectively increase and decrease the environmental efficiency of rainwater harvesting.     

Near-critical free-surface flows: real fluid flow analysis

An open channel flow with a flow depth close to the critical depth is characterised by a curvilinear streamline flow field that results in steady free surface undulations. Near critical flows of practical relevance encompass the undular hydraulic jump when the flow changes from supercritical (F > 1) to subcritical (F < 1), and the undular weir flow over broad-crested weirs where the flow changes from subcritical (F < 1) to supercritical (F > 1). So far these flows were mainly studied based on ideal fluid flow computations, for which the flow is assumed irrotational and, thus, shear forces are absent. While the approach is accurate for critical flow conditions (F = 1) in weir and flumes, near-critical flows involve long distances reaches, and the effect of friction on the flow properties cannot be neglected. In the present study the characteristics of near-critical free-surface flows are reanalysed based on a model accounting for both the streamline curvature and friction effects. Based on the improved model, some better agreement with experimental results is found, thereby highlighting the main frictional features of the flow profiles.     

Modeling of Cs migration in soils using an 80-year soil archive: role of fertilizers and agricultural amendments

An 80-year soil archive, the 42-plot experimental design at the INRA in Versailles (France), is used here to study long-term contamination by ¹³⁷Cs atmospheric deposition and the fate of this radioisotope when associated with various agricultural practices: fallow land, KCl, NH₄(NO₃), superphosphate fertilizers, horse manure and lime amendments. The pertinence of a simple box model, where radiocaesium is supposed to move downward by convectional mechanisms, is checked using samples from control plots which had been neither amended, nor cultivated since 1928. This simple model presents the advantage of depending on only two parameters: α, a proportional factor allowing the historical atmospheric ¹³⁷Cs fluxes to be reconstructed locally, and k, an annual loss coefficient from the plow horizon. Another pseudo-unknown is however necessary to run the model: the shape of historical ¹³⁷Cs deposition, but this function can be easily computed by merging several curves previously established by other surveys. A loss of ∼1.5% per year from the plow horizon, combined with appropriate fluxes, provides good concordance between simulated and measured values. In the 0–25 cm horizon, the residence half time is found to be ∼18 yr (including both migration and radioactive decay). Migration rate constants are also calculated for some plots receiving continuous long-term agricultural treatments. Comparison with the control plots reveals significant influence of amendments on ¹³⁷Cs mobility in these soils developed from a unique genoform.     

Fluoride Emissions and Forest Growth

Abstract

The October 1995 court decision allowing Ethyl Corporation to offer methylcyclopentadienyl manganese tricarbonyl (MMT) for sale to refiners for introduction into unleaded gasoline as an octane enhancer is likely to result in increased fine (PM_2.5) manganese (Mn) concentrations in ambient air. Concern exists regarding possible health effects. In this paper, recent fine Mn concentrations in three monitoring networks and one U.S. Environmental Protection Agency (EPA) study of personal exposure are analyzed. One network consists mainly of rural sites in national parks in the United States, a second consists mainly of urban sites in California, and the third consists mainly of urban sites in Canada where MMT has been used for a number of years. During the late 1980s and early 1990s, mean ambient concentrations ranged from 1 ng/m³ in the mostly rural network to 3 ng/m³ in the mostly urban California network to 12 ng/m³ in the MMT-impacted Canadian network. Several lines of evidence suggested that some of the fine Mn observed in the United States during the 1986-1992 period was contributed by automobiles using leaded gasoline, for which MMT was a registered fuel additive. However, the near-disappearance of leaded gasoline has resulted in a very small portion of fine Mn being attributed to automobiles in the years since 1992.A source apportionment analysis suggested that crustal contributions to ambient fine Mn are on the order of 1-2 ng/m³ in both the United States and Canada.     

On experimental setup in bioelectromagnetics

Bioeffects created by electromagnetic field (EMF) are the subject of intensive studies. This paper critically considers estimations of exposure to EMF in bioelectromagnetic experiments. Results of calculations presented herein show the significant role of the presence of conducting bodies (the exposure system) near an object under test on EMF energy absorption as well as mutual interactions between simultaneously exposed objects. Our aims herein are twofold: firstly to find a way to refer measurement results to free-space conditions in order to enable comparison of results obtained in different laboratories, and secondly to show that EMF energy absorption in any exposed object is different and that this difference is a function of the size of the exposure system, the number of exposed objects, and the particular properties (i.e., the electromagnetic structure) of the objects. In the authors’ opinion the existence of interactions caused by the presence of the exposure system and other exposed objects is a reason why remarkable differences are observed between experiments performed even under supposedly identical conditions. The presented considerations and conclusion suggest wider participation of physicists and engineers in bioelectromagnetic experiments in order to ensure the correctness of metrological aspects of these experiments.