三峡库区滑坡地带岩石特性的研究

针对三峡库区组成滑坡岩层的主要岩石——泥质岩、灰岩、砂岩,通过显微镜观察、X射线分析显微镜的定量分析及室内岩石力学强度试验,对各岩石的特性进行了分析。显微镜及X射线定量分析结果表明风化较弱的泥质岩基本上含有石英与钙质矿物,后者由于易溶于水而导致岩石的孔隙率增加。孔隙的一部分连接形成了裂缝, 从而使岩石的强度下降。各岩石的单轴压缩试验结果表明砂岩的强度最高,发生了风化的泥质砂岩的强度最低。在饱和状态下紫红色泥岩及风化了的泥质砂岩的单轴压缩强度降低最显著,比自然干燥状态下降低了大约50%, 推测是受粘土矿物含量的影响。所有岩石都表现出在峰值强度之前应力与应变几乎呈线性关系,而峰值强度之后应力急剧下降的脆性特征。这种在饱和状态下岩石强度大幅度下降与脆性特征表明在治理滑坡时需要采取十分周密及复杂的预防措施。     

Synthesis of Short-chain-length/Medium-chain-length Polyhydroxyalkanoate (PHA) Copolymers in Peroxisome of the Transgenic Arabidopsis Thaliana Harboring the PHA Synthase Gene from Pseudomonas sp. 61-3

In this paper, the photosynthetic production of short-chain-length/medium-chain-length polyhydroxyalkanoate (PHA) copolymers is reported. The wild-type and highly active doubly mutated PHA synthase 1 (S325T/Q481K, abbreviated ST/QK) genes from Pseudomonas sp. 61-3 were introduced into Arabidopsis thaliana. Peroxisome targeting signal 1 (PTS1) was used to target PHA synthases into the peroxisome to synthesize PHA from the intermediates of the β-oxidation pathway. The transgenic Arabidopsis produced PHA copolymers consisting of 40–57 mol% 3-hydroxybutyrate, 21–49 mol% 3-hydroxyvalerate, 8–18 mol% 3-hydroxyhexanoate, and 2–8 mol% 3-hydroxyoctanoate. The maximum PHA contents were 220μ g/g cell dry weight (cdw) in leaves, and 36μ g/g cdw in stems, respectively. The expression of the ST/QK mutated PHA synthase in leaves gene did not lead to significant difference in PHA content and monomer composition of PHAs, compared to the wild-type PHA synthase gene, suggesting that the supply of monomers may be a rate-determining step of PHA biosynthesis in the peroxisome. However, in stems, there were significant differences dependent on whether the wild-type or ST/QK mutated PHA synthase was expressed. These results suggest that tissue-specific monomer availability is important in determining the final mol% composition of PHA copolymers produced by the peroxisome in plants.     

Destruction of polychlorinated naphthalenes by a high-temperature melting treatment (GeoMelt process)

A series of treatment experiments were carried out to evaluate the applicability of a high-temperature melting treatment (GeoMelt process) to the destruction of polychlorinated naphthalene (PCN) formulation. We started with 10-kg-scale experiments in which a small melting furnace was used and then scaled up to a 1-t-scale experiment in which a melting furnace that resembled an actual treatment system was used. These runs were evaluated whether destruction efficiency (DE) of total PCNs was more than 99.999 % and whether concentrations of PCNs and polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/DFs) in vitrified materials, emission gas, and scrubber water were below the target levels. Because DE values and the target levels of PCNs and PCDDs/DFs in these runs were satisfactory, then we carried out a demonstrative experiment using the actual treatment system and confirmed destruction of PCNs. Based on good results of the demonstrative experiment, stock of PCN formulation was successfully treated continuously.     

Geochemical evaluation of present-day Tuul River sediments, Ulaanbaatar basin, Mongolia

The Tuul River flows through the Ulaanbaatar basin of Mongolia and is the main source of water for the capital city, Ulaanbaatar. The Tuul catchment can be divided into three parts around Ulaanbaatar (upper, middle, and lower), according to the extent of urbanization. Sixteen surface water and groundwater samples were collected to evaluate present-day water quality and 34 stream sediment samples taken to examine their geochemical composition in relation to provenance and to assess the impact of urban activity on heavy metal accumulation. Groundwater quality in the upper and central water sources was adequate, but high concentrations of NO ₃ ^? were found in the lower water source. Heavy metal concentrations in the sediments are evaluated by comparison with average upper continental crust (UCC) values, coupled with ecological risk assessment by reference to sediment quality guidelines (SQG). The results show average abundances of potentially toxic metals such as As, Pb, Zn, Cu, Ni, Cr, and V are higher in the middle part (within the city) than in the upper and lower parts. However, all three parts show depletion in some chalcophile and high field strength elements (Cu, Ni, Cr, Sr, Nb, Zr, Th, Sc) relative to UCC, indicating that the river sediments were derived from a highly felsic crustal source. The assessment using SQG shows As and Cr are present in levels that cause adverse aquatic biological effects. Although concentrations of Pb, Zn, Cu, and Ni are generally below their respective threshold effect levels, in the middle reaches, values increase and border on the probable effect level. This suggests significant anthropogenic contamination in the urban areas, increasing values above a naturally low regional background.     

Spectroscopic analysis of NIR-dye sensitization in bulk heterojunction polymer solar cells

The photovoltaic conversion efficiency for near-infrared (NIR) sunlight is improved successfully by dye sensitization of bulk heterojunction polymer solar cells, in which the active layer was prepared by a ternary blend of poly(3-hexylthiophene), a fullerene derivative (1-(3-methoxycarbonyl)propyl-1-phenyl-[6,6]-methanofullerene), and an NIR dye, silicon phthalocyanine bis(trihexylsilyl oxide). The mechanism of the NIR-dye sensitization is studied by femtosecond transient absorption spectroscopy.     

Elemental composition of sediments in Lake Jinzai, Japan: Assessment of sources and pollution

Bottom sediments from Lake Jinzai in southwest Japan were analyzed to determine their chemical compositions and to assess the potential for ecological harm by comparison with sediment quality guidelines. The pollution status of lake sediments was evaluated by employing contamination factor (CF), pollution load index (PLI), and geoaccumulation index (I(geo)), focusing on a suite of elements in lakebed and core sediments. Elevated concentrations of As, Pb, Zn, Cu, TOC, N, and P were present in several layers of the upper core and other surface sediments. The elevated metal concentrations are likely related to the fine-grained nature of the sediments, reducing bottom conditions produced by abundant organic matter, and possibly minor non-point anthropogenic sources. Moreover, correlations between the concentrations of trace metals and organic carbon, nitrogen, phosphorus, and iron, suggest that these elements play a role in controlling abundances. Calculated CF, PLI, and I(geo) indicate that the sediments are strongly polluted with respect to As, moderately to strongly polluted with Zn, and moderately polluted with Pb and Cu. Metal concentrations exceed the New York State Department of Environmental Conservation (NYSDEC) lowest effect level and the Canadian Council of Ministers of the Environment (CCME) interim sediment quality guidelines that indicate moderate impact on aquatic organisms in the study area.     

Behaviour of selected endocrine-disrupting chemicals in three sewage treatment plants of Beijing, China

Occurrence and fate of eight kinds of selected endocrine-disrupting compounds (EDCs) in three sewage treatment plants (STPs) of Beijing, China was investigated. These EDCs, composed of 4-octylphenol (4-OP), 4-n-nonylphenol (4-n-NP), bisphenol A (BPA), estrone (E1), 17α-estradiol (17α-E2), 17β-estradiol (E2), estriol (E3) and 17α-ethinylestradiol (EE2), in every step of STPs, were simultaneously analysed by gas chromatography/mass spectrometry after derivatisation. All the EDCs were detected in the influents of three STPs, and BPA was the most abundant compound. The concentrations of EDCs ranged from 36.6 ng/l of 17α-E2 (STP C) to 1342.3 ng/l of BPA (STP B) in the influent sewages and from below limits of detection of E2 and E3 (STP C) to 142.5 ng/l of E1 (STP B) in the effluent sewages. The STPs could not remove alkylphenols effectively from the aqueous phase with less than 40% reduction. BPA decreased over 90%, and steroid estrogens achieved considerable reductions from 64.8% of E2 to 94.9% of E3. Generally, biological treatment was more effective in removing alkylphenols, BPA and natural estrogens from the aqueous phase than primary treatment. However, the synthetic estrogen, EE2, was mostly removed by the primary treatment with about 63.5% reduction. It is the first time that the concentration of 17α-E2 in the sewage of China was reported in this paper. The compound might have a bearing with the waste effluents of dairy farms around urban area of Beijing.     

The sorption of heavy metal species by sediments in soakaways receiving urban road runoff

Infiltration facilities are designed for both the retention of non-point pollutants and the replenishment of groundwater in urban areas. In this study, sorption tests were conducted to evaluate the speciation of heavy metals and their behaviour in infiltration facilities receiving urban road runoff containing high DOC concentrations and stable heavy metal organic complexes. Road dust and three soakaway sediments were collected from heavy traffic areas and a residential area with an infiltration-type sewerage system in Tokyo, Japan. Sequential multiple batch tests were conducted by adding prepared road dust leachate (artificial road runoff) or deionised water to soakaway sediment to obtain soakaway sediment leachate (artificial percolating water from soakaway sediment), which mimicked the sorption by sediments in soakaways receiving urban road runoff. Heavy metal speciation was assessed by means of a combination of anion-exchange resin measurements and MINTEQA2 model calculations, and further validated by chelating resin measurements. In road dust leachates and soakaway sediment leachates, Cu predominantly existed as organic complexes and carbonates, whereas most Mn, Zn and Cd were found to exist in the form of free ions and carbonate complexes. Stable organic complexes of Cu in road dust leachates were strongly adsorbed by soakaway sediments despite the limited adsorption of DOC. On the other hand, desorption of free Mn, Zn and Cd ions from the sediment receiving road dust leachates was observed, indicating that heavy metals such as Mn, Zn and Cd may ultimately reach groundwater as free ions.     

Estrogen equivalent concentration of 13 branched para-nonylphenols in three technical mixtures by isomer-specific determination using their synthetic standards in SIM mode with GC-MS and two new diasteromeric isomers

Thirteen isomers of branched para-nonylphenols (para-NP) in three technical mixtures were isomer-specifically determined using their synthesized standards by SIM of structurally specific ions, m/z 135, 149 or 163 with GC–MS. Of the 13 isomers, four isomers, 4-(2,4-dimethylheptan-4-yl)phenol, 4-(4-methyloctan-4-yl)phenol, 4-(3-ethyl-2-methylhexan-2-yl)phenol (3E22NP) and 4-(2,3-dimethylheptan-2-yl)phenol synthesized for their determinations were first used as standard substances. The 13 isomers in the technical mixtures individually occurred at mass percent portion of more than 2%. The total mass percent portions in the mixtures from Tokyo Chemical Industry (TCI), Aldrich, and Fluka covered with 89 ± 2%, 75 ± 4% and 77 ± 2%, respectively. The abundance of 4-(3,6-dimethylheptan-3-yl)phenol in the three mixtures was the largest with 11.1 ± 2% to 9.9 ± 0.3%, while that of 4-(2-methyloctan-2-yl)phenol was the smallest with 2.9 ± 0.3% to 3.0 ± 0.2%. Additionally, structures of four new isomers of more than 1% portion present in a technical mixture were elucidated as two pairs of diastereomeric isomers: two types of 4-(3,4-dimethylheptan-4-yl)phenol (344NP) and those of 4-(3,4-dimethylheptan-3-yl)phenol (343NP). By estrogenic assay of 13 isomers with yeast estrogen screen system, the activity of 3E22NP was the highest, while that of 4-(3-methyloctan-3-yl)phenol was the least. Their relative activities to that of 3E22NP were individually calculated. Estrogenic equivalent concentrations of the three technical mixtures were predictively evaluated. The ratio of the EEC to the conventional concentration, total mass percent portions of the 13 isomers in technical mixtures were 0.208 for TCI, 0.206 for Aldrich and 0.205 for Fluka. The predicted estrogenic activity of measured concentration of para-NP in technical mixtures was approximately 5-fold greater than the measured estrogen agonist activity.     

Sustainability of silicon feedstock for a low-carbon society

We need to ensure the sustainable management of advanced materials, such as purified silicon, that contribute to a low-carbon society. Because a drastic increase in the demand for photovoltaic (PV) systems is tightening the supply of silicon for PV cells, the sustainability of silicon feedstock needs to be explored. For this purpose, a material flow analysis of silicon in Japan from 1996 to 2006 is presented in this paper. Our analysis finds that rapid growth in demand for polycrystalline silicon (pc-silicon) and single crystalline silicon (sc-silicon) has changed the structure of the purified silicon supply. The strong demand for purified silicon for solar cells is responsible for this change. While off-grade silicon obtained as a by-product of electronic-grade silicon (EG-Si) covered the demand for solar sells before 2000, pc-silicon is currently produced independently for solar cells via an energy-intensive process. Analysis of the resource effective-use index (REI), which indicates how effectively purified silicon is used, shows progress in the effective use of pc- and sc-silicon. REI analysis indicates that the effective use of pc-silicon is reaching a maximum, while the effective use of sc-silicon is advancing, with a corresponding increase in price. To ensure a sustainable supply of silicon feedstock, this paper proposes four solutions: (1) production of solar-grade pc-silicon by a less costly and less energy-consuming method; (2) reduction in the amount of crystalline silicon per watt in solar cells; (3) acceleration of the development and deployment of other solar cell types; and (4) reuse and recycling of solar cells in the future.