Baseline study of methane emission from open digesting tanks of palm oil mill effluent treatment

Anthropogenic release of greenhouse gases, especially CO₂ and CH₄ has been recognized as one of the main causes of global warming. Several measures under the Kyoto Protocol 1997 have been drawn up to reduce the greenhouse gases emission. One of the measures is Clean Development Mechanisms (CDM) that was created to enable developed countries to cooperate with developing countries in emission reduction activities. In Malaysia, palm oil industry particularly from palm oil mill effluent (POME) anaerobic treatment has been identified as an important source of CH₄. However, there is no study to quantify the actual CH₄ emission from the commercial scale wastewater treatment facility. Hence, this paper shall address the CH₄ emission from the open digesting tanks in Felda Serting Hilir Palm Oil Mill. CH₄ emission pattern was recorded for 52 weeks from 3600 m³ open digesting tanks. The findings indicated that the CH₄ content was between 13.5% and 49.0% which was lower than the value of 65% reported earlier. The biogas flow rate ranged between 0.8 l min⁻¹ m⁻² and 9.8 l min⁻¹ m⁻². Total CH₄ emission per open digesting tank was 518.9 kg day⁻¹. Relationships between CH₄ emission and total carbon removal and POME discharged were also discussed. Fluctuation of biogas production was observed throughout the studies as a result of seasonal oil palm cropping, mill activities, variation of POME quality and quantity discharged from the mill. Thus only through long-term field measurement CH₄ emission can be accurately estimated.     

PCB decomposition and formation in thermal treatment plant equipment

In this study we investigated both the decomposition and unintentional formation of polychlorinated biphenyl congeners during combustion experiments of refuse-derived fuel (RDF) and automobile shredder residue (ASR) at several stages in thermal treatment plant equipment composed of a primary combustion chamber, a secondary combustion chamber, and other equipments for flue gas treatment. In both experiments, the unintentional formation of PCB occurred in the primary combustion chamber at the same time as the decomposition of PCB in input samples. By combusting RDF, non-ortho-PCB predominantly formed, whereas ortho-PCB and symmetric chlorinated biphenyls (e.g., #52/69, #87/108, and #151) tended to be decomposed. ASR formed the higher chlorinated biphenyls more than RDF. These by-products from ASR had no structural relation with ortho-chlorine. Lower chlorinated biphenyls appeared as predominant homologues at the final exit site, while all congeners from lower to higher chlorinated PCB were unintentionally formed as by-products in the primary combustion chamber. This result showed that the flue gas treatment equipments effectively removed higher chlorinated PCB. Input marker congeners of RDF were #11, #39, and #68, while those for ASR were #11, #101, #110/120, and #118. Otherwise, combustion marker congeners of RDF were #13/12, #35, #77, and #126, while those for ASR were #170, #194, #206, and #209. While the concentration of PCB increased significantly in the primary combustion chamber, the value of toxicity equivalency quantity for dioxin-like PCB decreased in the secondary combustion chamber and the flue gas treatment equipments.     

Congener profiles of PCB and a proposed new set of indicator congeners

In this study, a new method for calculating total PCB and toxic equivalents (TEQ) of coplanar PCB (Co-PCB) was proposed, called the 'PCB dual method'. This method analysed various kinds of technical PCB, samples contaminated by technical PCB and byproduct PCB. In the PCB dual method, a data set of 15 indicator congeners was utilized for the calculations, having IUPAC nos. #3, #8, #28, #52, #77, #101, #105, #118, #126, #138, #153, #180, #194, #206 and #209. The 15 congener set was chosen from the major congeners, determined by HRGC/HRMS analysis, in 18 technical PCB, Kanechlor, Aroclor, Clophen and Chlorofen, and 20 other samples, such as indoor air, flue gases, emission gases, municipal solid waste (MSW), ash and sealant. To obtain total PCB and TEQ of Co-PCB, the intermediate sum for the concentration of the 15 congeners was multiplied by each multiplication factor. As a result, we obtained the average factor used to calculate total PCB in technical PCB and other samples. For technical PCB, the factor was 3.01, while for indoor air samples, flue and emission gases, MSW, ash and sealants, the factors were 3.92, 4.16, 3.68, 4.52 and 4.77, respectively. Moreover, the factor used to calculate the TEQ of Co-PCB in Kanechlor and other source samples were also obtained. The factors for Kanechlor, indoor air samples and emission gases from a cement plant were in the order of 10(-5), while the factor for flue gases in a MSW incinerator was in the order of 10(-3). These data were valuable for the rough estimation of the TEQ of Co-PCB without separation from other PCB before individual measurements.     

Economic analysis of biogas and compost projects in a palm oil mill with clean development mechanism in Malaysia

This article is a case study to compare the economic viabilities of biogas generation and compost projects in a palm oil mill in Malaysia with and without clean development mechanism (CDM). Biogas is captured from anaerobic ponds or digester tanks treating palm oil mill effluent (POME) and converted to green renewable electricity for grid connection, while compost is produced from the shredded empty fruit bunch and raw untreated POME. The both technologies were compared by considering the changes of the materials flow and energy balances. A palm oil mill with a capacity of 54?t fresh fruit bunch per hour has the potential to produce either 6.9?GWh of electricity from biogas or fertilizer equivalent to 488?t of nitrogen, 76?t of phosphorus and 1,065?t of potassium per year. The economic analysis for 10?years project term analysis indicated that CDM gave a significant impact and ensured economic viability for both projects with 25?% of internal rate of return (IRR), RM 12.39 million of net present value (NPV) and 3.5?years of payback period (PBP) for biogas project, whereas 31?% of IRR, RM 10.87 million of NPV and 2.9?years of PBP for compost project, respectively. In addition, sensitivity analysis indicated that the profitability of both projects will vary depending on the economic situation, such as electricity price which is based on the government policy, whereas compost price that depend on fertilizer market price with 43?% NPV change in 20?% range of fertilizer value.     

Production and characterization of KOH-activated carbon derived from polychlorinated biphenyl residue generated by the sodium dispersion process

Polychlorinated biphenyl (PCB) residues from the sodium dispersion (SD) process were employed as the raw materials for the production of activated carbon using KOH activation. The pore properties, such as the specific surface area and pore size distribution, were characterized using the Barrett–Joyner–Halenda method and the Horvath–Kawazoe method based on the N₂ adsorption isotherm at 77 K. The activated carbon produced showed similar adsorption capacities and specific surface areas to the commercially available product. The effects of the activation conditions on the porosity of the activated carbon produced were studied. The most significant factor affecting the specific surface proved to be the activation temperature. The activated carbon produced from PCB residues from the high-temperature (423–443 K) SD process had a binary pore size distribution well developed in the 4 nm region and in the micropore region. The pore structure of the carbon produced from PCB residues from the low-temperature (333–393 K) SD process had a wide range of micropores and mesopores.     

Reduction of Methane Released from Palm Oil Mill Lagoon in Malaysia and Its Countermeasures

Palm oil industry in Malaysia is one of the potential candidates for the CDM project because large amount of methane is emitted from the lagoons and open digesting tank of the wastewater treatment system. Therefore the first objective of the project is to investigate the actual GHG emission from the lagoons and open digesting tank in palm oil mills in order to establish the baseline for CDM project. Results indicated that methane contribution to biogas released from the open digesting tank and lagoon systems were 35% and 45%, respectively. These values are much lower than the reported value of 65% obtained by complete anaerobic condition of lab-scale experiments. Based on actual methane release measurement and information gathered from palm oil mill about wastewater treatment, significant amount of methane emission to the atmosphere can be reduced with the installation of new closed digesting tank system converted from the open digesting tank such as just by covering it with applying CDM. It is estimated that a total of RM2.6 million could be obtained from the selling of electricity generated from biogas generation and Certified Emission Reduction(CER). This revised version was published online in August 2006 with corrections to the Cover Date.     

Evolution of male dimorphic allometry in a population of the Japanese horned beetle <Emphasis Type="Italic">Trypoxylus dichotomus septentrionalis</Emphasis>

I conducted a detailed morphological analysis of the Japanese horned beetle Trypoxylus dichotomus septentrionalis to clarify the allometric relationship between horn length and body size and examined its mating success and reproductive behaviour in the field. The relationship between horn and body size was not discontinuous at the switch point body size, but the slope of the linear relationship changed at the switch point. Shape of the allometric relationship was initially steep and became flatten around the switch point in both linear and log scales; that is, minor males showed a positive relationship and major males showed a negative one. Major males gained more mating success than minor males. Within major males, individuals with larger horn or body size had higher mating success than individuals with smaller ones. Within minor males there were no differences in horn and body size between mated and unmated individuals. Although sneak-like behaviours were exhibited by both morphs, it is likely that these behaviours rarely lead to direct benefit. These results suggest that dimorphic allometry of T. dichotomus is consistent with the hypothesis of a continuous reaction norm that meets a ceiling, which restrains further allometric growth.     

Deposition of 137Cs in Rokkasho, Japan and its relation to Asian dust

Biweekly atmospheric depositions of (137)Cs were measured in Rokkasho, Aomori, Japan from March 2000 to March 2006 to study recent (137)Cs deposition. Although the deposition level was generally lower than the detectable limit, deposition samples collected in spring occasionally had measurable levels of (137)Cs. The annual (137)Cs deposition from 2001 to 2005 was 0.04-0.69 Bq m(-2) with a mean value of 0.27 Bq m(-2). Depositions of insoluble Al, Fe and Ti were strongly correlated with the (137)Cs deposition, suggesting that suspension of soil particles was the main source of the recent (137)Cs deposition. Asian dust events were coincident with some of the significant (137)Cs depositions in spring. It was found that the ratios of (137)Cs/Al and Fe/Al could be used as indices for discriminating Asian dust from suspension of the local surface soil. Backward trajectory analysis suggested southern Mongolian and northeastern China regions as sources of the significant (137)Cs depositions.     

Inventories of Pu, Cs, and excess Pb in sediments from freshwater and brackish lakes in Rokkasho, Japan, adjacent to a spent nuclear fuel reprocessing plant

We investigated the vertical profiles of ^239+240Pu, ¹³⁷Cs, and excess ²¹⁰Pb (²¹⁰Pb_ex) in sediment core samples obtained from two freshwater lakes and two brackish lakes situated near the first commercial spent nuclear fuel reprocessing plant in Rokkasho, Japan, before the final test of the plant using actual spent nuclear fuel. The inventory of ^239+240Pu in those lakes was larger than that in soil in Rokkasho, which indicated the inflow of ^239+240Pu from the catchment area in addition to direct deposition on the lake surfaces. The ¹³⁷Cs inventory in sediments of the brackish lakes was lower than that in the soil, which showed that part of the ¹³⁷Cs was removed from the sediments by the brackish water or that it was not deposited into the sediments, because of the high solubility of Cs in brackish water. The ¹³⁷Cs inventory in sediments of the freshwater lakes was higher than that of the brackish lakes, and comparable with that in soil except for one core sample out of four. The ^239+240Pu/¹³⁷Cs ratio in freshwater lake sediments was higher than that in soil, and that indicated that part of the ¹³⁷Cs was lost from the sediments. The low inventory of ¹³⁷Cs may be attributable to competition for absorption sites in sediments with ammonium ions formed in the reducing environment which occurs from summer to fall in the sediments. Those data will be used as background data on the artificial radionuclides in the lakes to assess the effect of released radionuclides on their concentrations.     

Turning waste to wealth-biodegradable plastics polyhydroxyalkanoates from palm oil mill effluent – a Malaysian perspective

Palm oil industries have been contributing significantly towards the country’s economy and increase standard of living among Malaysians. However, it has also been identified as the major contributor for discharging the largest pollution load throughout the country. Owing to high biochemical oxygen demand (BOD) and chemical oxygen demand (COD), the palm oil mill effluent (POME) cannot be discharged directly into the environment. Thus, palm oil industries are facing tremendous challenges in order to comply with environmental regulations. While anaerobic digestion has been employed by most mills as primary treatment, POME can also be a potential source of degradable organic material which can be converted into value-added products and fine chemicals. Organic acids generated during acid-phase anaerobic digestion of POME could be a potential carbon source for the production of polyhydroxyalkanoates (PHA)- a biodegradable thermoplastic material of microbial origin. This paper aims at understanding how organic acids from POME may serve as a renewable feedstock for the biosynthesis of PHA.