Histopathological changes in zebrafish embryos exposed to DLPCBs extract from Zhanjiang coastal sediment

Dioxin-like polychlorinated biphenyls (DLPCBs) are ubiquitous persistent pollutants that cause adverse effects in many environmental organisms. DLPCBs in marine sediments can be absorbed by benthic organisms, bioaccumulate, and biomagnify through the food chain and threaten animal and human health. There are no reports of DLPCBs concentrations in the Zhanjiang Gulf seabed. This study was designed to investigate the concentration of DLPCBs in the Zhanjiang coastal sediment and histopathological changes in zebrafish (Diano rerio) embryos exposed to environmentally relevant concentrations of DLPCBs. Of the five sites selected, two sites TS and JSW contained DLPCBs at concentrations of 0.08 and 22.54 ng/g dry sediment, respectively. Two groups of zebrafish embryos were used. One group was exposed to 3.75, 7.5, 15, 30, and 60 mg/ml of DLPCBs extracted from the sediments sampled from the TS site and the second group to 4.375, 8.75, 17.5, 35, and 70 mg/ml of DLPCBs from JSW site from 0.75 h post-fertilization (hpf) to 96 hpf. The zebrafish exposed to 60 and 70 mg/ml of DLPCBs at 96 hpf displayed gross histopathological changes with cardiac lesions including pericardial edema being the most deleterious. Other changes observed were hydropic degeneration of gill filaments and hepatocytes, loss of intestinal folds, and uninflated swim bladder. It appears that only a few sites of the Zhanjiang gulf are contaminated with DLPCBs. This is the first report of histopathological changes in the gills, hepatocytes, intestines, heart, and the swim bladder in zebrafish embryos exposed to DLPCBs from a coastal sediment. Further studies with sampling at different stages of development are required to identify which organ/tissue is most sensitive to DLPCBs.     

Predictive modelling of piezometric head and seepage discharge in earth dam using soft computational models

Environmental Science and Pollution Research - Predictions of pore pressure and seepage discharge are the most important parameters in the design of earth dams and assessing their safety during the...     

Effect of new organic supplement (Panchgavya) on seed germination and soil quality

We studied the suitability of Panchgavya (five products of cow), new organic amendment, application on seed germination, plant growth, and soil health. After characterization, Panchgavya was mixed with water to form different concentration and was tested for seed germination, germination index, and root and shoot growth of different seedlings. Four percent solution of Panchgavya was applied to different plants to test its efficacy. Panchgavya and other two organic amendments were incorporated in soil to test the change of soil chemical and microbiological parameters. Panchgavya contained higher nutrients as compared to farm yard manure (FYM) and vermicompost. Its application on different seeds has positively influenced germination percentage, germination index, root and shoot length, and fresh and dry weight of the seedling. Water-soluble macronutrients including pH and metal were positively and negatively correlated with the growth parameters, respectively. Four percent solution of Panchgavya application on some plants showed superiority in terms of plant height and chlorophyll content. Panchgavya-applied soil had higher values of macro and micronutrients (zinc, copper, and manganese), microbial activity as compared to FYM, and vermicompost applied soils. Application of Panchgavya can be gainfully used as an alternative organic supplement in agriculture.     

Performance evaluation of reverse logistics enterprise – an agent-based simulation approach

Reverse logistics (RL) has been applied in many industries and sectors since its conception. Unlike forward logistics, retracing consumer goods from the point of consumption to the point of inception is not a well-studied process. It involves many uncertainties such as time, quality and quantity of returns. The returned products can be remanufactured, have parts harvested, or be disposed safely. It is important to implement these activities in a cost-effective manner. The aim of this research is to measure the performance of the RL enterprise with the help of an agent-based simulation model. The major entities in the RL network are considered as Agents that can act independently. There are several different agents: collector agent, sorting-cum-reuse agent, remanufacturing agent, recycler agent, supplier agent and distributor agent. The individual performances of the agents are measured and recommendations are given to improve their performance, leading to the enhancement of the total performance of the RL enterprise. The approach is applied to a case study involving cell phone remanufacturing.     

Assessment of nitrogen losses through nitrous oxide from abattoir wastewater-irrigated soils

The land disposal of waste and wastewater is a major source of N₂O emission. This is due to the presence of high concentrations of nitrogen (N) and carbon in the waste. Abattoir wastewater contains 186 mg/L of N and 30.4 mg/L of P. The equivalent of 3 kg of abattoir wastewater-irrigated soil was sieved and taken in a 4-L plastic container. Abattoir wastewater was used for irrigating the plants at the rates of 50 and 100 % field capacity (FC). Four crop species were used with no crop serving as a control. Nitrous oxide emission was monitored using a closed chamber technique. The chamber was placed inside the plastic container, and N₂O emission was measured for 7 days after the planting. A syringe and pre-evacuated vial were used for collecting the gas samples; a fresh and clean syringe was used each time to avoid cross-contamination. The collected gas samples were injected into a gas chromatography device immediately after each sampling to analyse the concentration of N₂O from different treatments. The overall N₂O emission was compared for all the crops under two different abattoir wastewater treatment rates (50 and 100 % FC). Under 100 % FC (wastewater irrigation), among the four species grown in the abattoir wastewater-irrigated soil, Medicago sativa (23 mg/pot), Sinapis alba (21 mg/pot), Zea mays (20 mg/pot) and Helianthus annuus (20 mg/pot) showed higher N₂O emission compared to the 50 % treatments—M. sativa (17 mg/pot), S. alba (17 mg/pot), Z. mays (18 mg/pot) and H. annuus (18 mg/pot). Similarly, pots with plants have shown 15 % less emission than the pots without plants. Similar trends of N₂O emission flux were observed between the irrigation period (4-week period) for 50 % FC and 100 % FC. Under the 100 % FC loading rate treatments, the highest N₂O emission was in the following order: week 1 > week 4 > week 3 > week 2. On the other hand, under the 50 % FC loading rate treatments, the highest N₂O emission was recorded in the first few weeks and in the following order: week 1 > week 2 > week 3 > week > 4. Since N₂O is a greenhouse gas with high global warming potential, its emission from wastewater irrigation is likely to impact global climate change. Therefore, it is important to examine the effects of abattoir wastewater irrigation on soil for N₂O emission potential.

     

Simulations and experiments in punching spring-steel devices with sub-millimeter features

This work demonstrates the feasibility of meso-scale (100 μm to mm) punching of multiple holes of intricate shapes in metals. Analytical modeling, finite element (FE) simulation, and experimentation are used in this work. Two-dimensional FE simulations in ABAQUS were done with an assumed material modeling and plane-strain condition. A known analytical model was used and compared with the ABAQUS simulation results to understand the effects of clearance between the punch and the die. FE simulation in ABAQUS was done for different clearances and corner radii of the punch, die, and holder. To complement modeling with real experiments and for the purpose of comparison, a set of punches and dies were made to punch out a miniature spring-steel gripper. Comparison of compliant grippers made by wire-cut electro discharge machining (EDM) and punching shows that realizing sharp interior and re-entrant corners by punching is not easy to achieve. However, the promise of realizing meso-scale parts with complicated shapes through punching is demonstrated in this work; and further work is identified and some strategies are suggested for improvement. The main contribution of this paper is in adapting the well-established punching and blanking operations to the meso-scale as a viable alternative to making miniature devices currently dominated by lithography-based techniques.     

Multivariate analysis of mixed contaminants (PAHs and heavy metals) at manufactured gas plant site soils

Principal component analysis (PCA) was used to provide an overview of the distribution pattern of polycyclic aromatic hydrocarbons (PAHs) and heavy metals in former manufactured gas plant (MGP) site soils. PCA is the powerful multivariate method to identify the patterns in data and expressing their similarities and differences. Ten PAHs (naphthalene, acenapthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, chrysene, benzo[a]pyrene) and four toxic heavy metals — lead (Pb), cadmium (Cd), chromium (Cr) and zinc (Zn) — were detected in the site soils. PAH contamination was contributed equally by both low and high molecular weight PAHs. PCA was performed using the varimax rotation method in SPSS, 17.0. Two principal components accounting for 91.7% of the total variance was retained using scree test. Principle component 1 (PC1) substantially explained the dominance of PAH contamination in the MGP site soils. All PAHs, except anthracene, were positively correlated in PC1. There was a common thread in high molecular weight PAHs loadings, where the loadings were inversely proportional to the hydrophobicity and molecular weight of individual PAHs. Anthracene, which was less correlated with other individual PAHs, deviated well from the origin which can be ascribed to its lower toxicity and different origin than its isomer phenanthrene. Among the four major heavy metals studied in MGP sites, Pb, Cd and Cr were negatively correlated in PC1 but showed strong positive correlation in principle component 2 (PC2). Although metals may not have originated directly from gaswork processes, the correlation between PAHs and metals suggests that the materials used in these sites may have contributed to high concentrations of Pb, Cd, Cr and Zn. Thus, multivariate analysis helped to identify the sources of PAHs, heavy metals and their association in MGP site, and thereby better characterise the site risk, which would not be possible if one uses chemical analysis alone.