Surface complexation modeling of Yb(III) sorption and desorption on hematite and alumina

Sorption and desorption of Yb(III) were studied on hematite and on alumina using a surface complexation model. The experimental methodology was conceived to allow an analysis of the data using a constant capacitance model. The FITEQL code was used for the calculations.The experimental results tend to show reversibility of sorption when the surface loading is small, and irreversibility when the surface loading is high. Surface complexation modeling gives a good interpretation of these two phenomena, taking into account hydroxylation of the surface complexes. In these two cases, it is possible to describe sorption and desorption curves with the same surface stoichiometries and the same surface complexation constants. The existence of these surface complexes depends on the pH of the solution, surface loading, and reaction direction.     

Experimental investigation of performance and emission characteristics of diesel engine using Jatropha biodiesel with alumina nanoparticles

Biodiesels have come up as a very strong alternative for diesel fuel. Biodiesels such as Jatropha Oil Methyl Ester (JOME) are comparable in performance with that of the diesel engine. The thermal efficiency of engines fuelled with biodiesels was found lower than conventional diesel fuel but due to the bio-origin, the emission characteristics are much better. However, biodiesel increases the NOx emissions as these are rich in oxygen, hence nanoparticles are used in this experiment to curb the high temperatures and reduce the NOx formation. The experiment on naturally aspired diesel engine was conducted with four prepared test fuels other than neat diesel and neat biodiesel. The 50 and 150 of alumina nanoparticles were added separately to the pure diesel and pure Jatropha biodiesel to form the nano emulsions using ultrasonicator. The properties of nanoemulsion were evaluated using dynamic light scattering technique using zetasizer. The performance and emission characteristics of multi-cylinder diesel engine with these nanoemulsions were compared with that of neat fuels. The results showed that using nanoparticles with diesel and biodiesel can contribute in a more efficient, economical, and eco-friendly engine operation.     

Effects of temperature and composite alumina on pyrolysis of sewage sludge

An interactive dual-circulating fluidized bed system has been proposed in which the pyrolysis of sewage sludge(SS) and incineration of biomass proceed simultaneously, and alumina is used as the bed material and heat carrier. The alumina coated with biomass ash would mix with sewage sludge in the pyrolysis reactor of this device. It is important to know the influence of composite alumina(CA) on the pyrolysis progress. Sewage sludge was pyrolyzed in a fixed bed reactor from 400 to 600°C using CA as catalyst. The effects of temperature and CA additive ratio on the products were investigated. The product yields and component distribution of non-condensable gas were more sensitive to the change of temperature, and the maximum liquid yield of 48.44 wt.% and maximum Useable Energy of Liquid of 3871 k J/kg sludge were observed at 500°C with 1/5 CA/SS(mass ratio). The gas chromatography–mass spectrometry results showed that the increase of temperature enhanced devolatilization of organic matter and promoted cyclization and aromatization of aliphatics. The presence of CA could strengthen secondary cracking and interaction among primary products from different organic compounds, such as acid–amine condensation,and reduce the content of oxygenated compounds. When the CA additive amount exceeded a certain proportion, the aromatization was clearly strengthened. The effects of CA on decomposition of fatty acids and formation of aromatics were similar to that of temperature. This means that the reaction temperature could be lowered by introducing CA, which has a positive effect on reducing energy consumption.     

Iron and aluminium based adsorption strategies for removing arsenic from water

Arsenic is a commonly occurring toxic metal in natural systems and is the root cause of many diseases and disorders. Occurrence of arsenic contaminated water is reported from several countries all over the world. A great deal of research over recent decades has been motivated by the requirement to lower the concentration of arsenic in drinking water and the need to develop low cost techniques which can be widely applied for arsenic removal from contaminated water. This review briefly presents iron and aluminium based adsorbents for arsenic removal. Studies carried out on oxidation of arsenic(III) to arsenic(V) employing various oxidising agents to facilitate arsenic removal are briefly mentioned. Effects of competing ions, As:Fe ratios, arsenic(V) vs. arsenic(III) removal using ferrihydrite as the adsorbent have been discussed. Recent efforts made for investigating arsenic adsorption on iron hydroxides/oxyhydroxides/oxides such as granular ferric hydroxide, goethite, akaganeite, magnetite and haematite have been reviewed. The adsorption behaviours of activated alumina, gibbsite, bauxite, activated bauxite, layered double hydroxides are discussed. Point-of-use adsorptive remediation methods indicate that Sono Arsenic filter and Kanchan™ Arsenic filter are in operation at various locations of Bangladesh and Nepal. The relative merits and demerits of such filters have been discussed. Evaluation of kits used for at-site arsenic estimation by various researchers also forms a part of this review.     

Effect of Al2O3 particle size reduction on aluminium dust explosion

To investigate the effect of Al₂O₃ particle size on an aluminum explosion, the overpressure and flame velocity in a vertical duct were evaluated. The results show that the inhibitory effect of submicron Al₂O₃ is best, while the inhibitory effect increases with increasing inerting ratio. However, the inhibitory effect of micron Al₂O₃ does not increase significantly after the inerting ratio exceeds 40%. For high-concentration aluminum powder, 0.8 μm Al₂O₃ with an inerting ratio less than 20% promotes aluminum explosion. As the inerting ratio increases beyond 20%, however, the overpressure decreases. Furthermore, Al₂O₃ inhibits the formation of the intermediate product AlO and decreases the flame brightness. As the inerting ratio of 0.8 μm Al₂O₃ reaches 50%, the white patches in the flame image disappear. The results of scanning electron microscopy showed that the explosion products agglomerate and some dot-like protrusions appear on the surface of the unburned aluminum particles. The inhibition mechanism was qualitatively investigated. Physical heat absorption is proven to play a limited role. Thermal radiation and chemical inhibition play a key role. The chemical effect mainly influences the surface reaction energy source.     

Evaluating the efficacy of alumina/carbon nanotube hybrid adsorbents in removing Azo Reactive Red 198 and Blue 19 dyes from aqueous solutions

Concerning the high volume of wastewater containing dye in Iran and its adverse effects, it is necessary to develop scientific solutions for treating these wastewaters. The aim of this study was to evaluate the efficiency of the alumina-coated multi-walled carbon nanotubes in removing the Reactive Red 198 (RR 198) and Blue 19 (RB 19) dyes. Synthetic samples including dye with different concentrations were prepared. These samples were put in contact with different contents of alumina/multi-walled carbon nanotubes, in different pH values, in different contact times, different temperatures and the presence of sodium sulfate or sodium carbonate. The optimum pH, dye concentration and temperature for removal of the two dyes was 3, 50 mg l⁻¹ and 25 °C, respectively. The optimum adsorbent dose for removal the RR 198 dye was 0.5 g l⁻¹ and for Blue 19 was 0.4 g l⁻¹. The optimum contact time for RR 198 was 150 min and RB 19 was 180 min. In this condition, maximum removal efficiency for RR 198 and RB 19 was 91.54% and 93.51%, respectively. The adsorption study was analyzed kinetically, and the results revealed that the adsorption fitted a pseudo-second order kinetic model. According to these results alumina/multi-walled carbon nanotubes can effectively remove RR 198 and RB 19 from aqueous solutions.     

Reductive decomposition of waste gypsum with SiO<Subscript>2</Subscript>, Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> additives

From the point of view of a sustainable and environment-friendly society based on the recycling of material resources, it is preferable to utilize waste gypsum as a substitute for lime, which is currently produced by the calcination of limestone. In the present work, the reductive decomposition of CaSO₄ was investigated under an atmosphere of CO: 2 vol%, CO₂: 30 vol%, with N₂ as a carrier gas without and with the addition of SiO₂, Al₂O₃, or Fe₂O₃. It was found that the decomposition temperature of CaSO₄ was significantly reduced from 1673 K to 1223 K when only 5 wt% Fe₂O₃ was added to CaSO₄. In the case of the addition of SiO₂ or Al₂O₃ to CaSO₄, the decomposition temperature was reduced from 1673 K to 1623 K. This was due to the formation of composite oxides (calcium ferrite, calcium silicate, or calcium aluminate) during the reaction of CaSO₄ with the additives at a lower temperature. In addition, the formation of unfavorable product CaS was inhibited in the presence of 5 wt% Fe₂O₃, and this inhibition effect further increased as the addition of Fe₂O₃ was increased. In contrast, no significant effect on the inhibition of CaS formation was observed on the addition of SiO₂ or Al₂O₃.