Case study of landfill leachate recirculation using small-diameter vertical wells

A case study of landfill liquids addition using small diameter (5 cm) vertical wells is reported. More than 25,000 m³ of leachate was added via 134 vertical wells installed 3 m, 12 m, and 18 m deep over five years in a landfill in Florida, US. Liquids addition performance (flow rate per unit screen length per unit liquid head) ranged from 5.6 × 10^?8 to 3.6 × 10^?6 m³ s^?1 per m screen length per m liquid head. The estimated radial hydraulic conductivity ranged from 3.5 × 10^?6 to 4.2 × 10^?4 m s^?1. The extent of lateral moisture movement ranged from 8 to 10 m based on the responses of moisture sensors installed around vertical well clusters, and surface seeps were found to limit the achievable liquids addition rates, despite the use of concrete collars under a pressurized liquids addition scenario. The average moisture content before (51 samples) and after (272 samples) the recirculation experiments were 23% (wet weight basis) and 45% (wet weight basis), respectively, and biochemical methane potential measurements of excavated waste indicated significant (p < 0.025) decomposition.     

Multi-criteria evaluation technique for SFI site identification of NORMS and oil industry waste disposal – Possibilities in Kuwait

Waste generation and accumulating quantities of oil field waste are a matter of environmental concern. This study proposes the Slurry Fracture Injection (SFI) technique as an alternative waste disposal method. The slurried solids injection waste disposal method is environmentally secure and permanent, leaving no future liabilities that must be risk-evaluated or priced. An entire waste stream comprising ground solids and waste water can be injected into deep and hydraulically secure target strata with no contamination of potable water-bearing formations or formations outside the target zone that may contain resources (gas and oil). The slurry injection method can be used to clean and reclaim landfills, oil pits and granular waste dumps. This article proposes a two-tier screening method for evaluating the feasibility of this technique and the identification of suitable target zones. A stringent environmental and process control monitoring program should complement the planning and operational period to ensure environmental protection, waste containment, and regulatory HSE compliance.     

气袋直接进样法测定丙烯腈

采用气袋直接进样法测定环境和污染源空气中的丙烯腈。结果表明:丙烯腈在0.4～99.5 mg/m3浓度范围内具有良好的线性关系,相关系数为0.999 8。在低、中、高3个添加水平回收率为88.9%~100%,相对标准偏差为0.6%~4.7%,均能较好地满足实验室分析要求。     

Storage of CO2 in saline aquifers: Effects of gravity, viscous, and capillary forces on amount and timing of trapping

CO₂ can be effectively immobilized during CO₂ injection into saline aquifers by residual trapping – also known as capillary trapping – a process resulting from capillary snap-off of isolated CO₂ bubbles. Simulations of CO₂ injection were performed to investigate the interplay of viscous and gravity forces and capillary trapping of CO₂. Results of those simulations show that gas injection processes in which gravitational forces are weak compared to viscous forces (low gravity number N_gv) trap significantly more CO₂ than do flows with strong gravitational forces relative to the viscous forces (high N_gv). The results also indicate that over a wide range of gravity numbers (N_gv), significant fractions of the trapping of CO₂ can occur relatively quickly. The amount of CO₂ that is trapped after injection ceases is demonstrated to correlate with N_gv. For some simulated displacements, effects of capillary pressure and aquifer dip angle on the amount and the rate of trapping are reported. Trapping increases when effects of capillary pressure and aquifer inclination are included in the model. Finally we show that injection schemes such as alternating injection of brine and CO₂ or brine injection after CO₂ injection can also enhance the trapping behavior.     

探讨“烟塔合一”技术在环评中大气环境的防护距离

归纳"烟塔合一"项目评估的共性要求,在分析德国模式不能充分反映特定条件下对近距离保护目标影响的基础上,阐明了环境防护距离设置的必要性,并就目前所采取环境防护距离计算方法及部分项目风洞试验结果进行解析,提出相关建议。     

Corrosion behavior of steels for CO2 injection

The process chain for Carbon Capture and Sequestration (CCS) includes tubing for injection of CO₂ into saline aquifers. The compressed CO₂ is likely to contain specific impurities; small concentrations of SO₂ and NO₂ in combination with oxygen and humidity are most harmful. In addition, CO₂ saturated brine is supposed to rise in the well when the injection process is interrupted. The material selection has to ensure that neither CO₂ nor brine or a combination of both will leak out of the inner tubing. In this comprehensive paper the investigated materials range from low-alloy steels and 13% Cr steels up to high-alloy materials. Electrochemical tests as well as long term exposure tests were performed in CO₂, in brine and combination of both; pressure was up to 100 bar, temperature up to 60 °C. Whereas the CO₂ stream itself can be handled using low alloy steels, combinations of CO₂ and brine require more resistant materials to control the strong tendency to pitting corrosion. The corrosion behavior of heat-treated steels depends on factors such as microstructure and carbon content. For different sections of the injection tube, appropriate materials should be used to guarantee safety and consider cost effectiveness.     

在线分离富集FI分光光度法直接测定铜

本文针对ＡＡＳ法测定痕量铜时，大量铁存在表现干扰，研究并建立了流动注射（ＦＩ）在线螯合树脂分离富集光度法直接测定痕量铜的新方法，具有灵敏度高、选择性强；因此，已成功地用于水样中痕量铜的测定，该法在水质检验和环境监测中有一定的适用性．     

基于CBR的注塑模结构智能设计系统研究

通过对基于事例推理 (CBR)技术及注塑模设计过程的分析 ,得出将CBR思想应用到注塑模结构设计中的可行性和必要性 ,提出了一个基于事例的注塑模结构智能设计系统的总体结构 ,并分析了关键技术的实现方法     

海水中总氮的测定方法比较研究

通过标准曲线、检出限和测定范围、方法精密度、方法准确度、实际海水样品测定结果、加标回收率、分析效率和物料消耗这几方面比较了过硫酸钾氧化法、流动注射分析法和高温氧化-化学发光检测法这3种测定海水中总氮(TN)方法的优缺点。结果表明,流动注射分析法和高温氧化-化学发光检测法的测定范围更宽,精密度、准确度更好,3种样品的加标回收率达到96.2%~101%;高温氧化-化学发光检测法分析效率高、物料消耗少、节能环保,适用于一般海水样品的批量分析,且由于测定范围大,该法也适用于TN浓度较高的海水样品的批量分析,流动注射分析法因其较低的检出限更适用于TN浓度较低的海水样品的批量分析。     

废旧塑料综合利用新方法——高炉喷吹废塑料技术

介绍了废旧塑料综合利用的新方法－高炉喷吹废料技术。通过比较，表明高喷吹废塑料技术在各方面均优于废旧塑料的其他处理方法；并简要对我国高炉喷吹废塑料作了可行性论证。