2024铝合金连接结构两种防护涂层耐蚀性研究

目的研究铝合金两种防护涂层在5%NaCl盐雾环境下的腐蚀疲劳性能。方法针对在两种涂层防护作用下的2024铝合金连接结构,开展实验室加速试验,采用"腐蚀环境-疲劳加载"交替循环的试验模式,得到铝合金两种防护涂层在5%NaCl盐雾环境下的腐蚀疲劳寿命值,对比分析涂层体系对铝合金连接结构的腐蚀疲劳寿命影响。结果 5%NaCl盐雾环境对于铝合金连接结构疲劳寿命有较大影响,相较于传统涂层,纳米涂层在5%NaCl盐雾环境下的防护效果更好。结论纳米涂层表面破坏后快速生成的致密氧化膜能有效提高涂层的耐蚀性能。     

一株苯酚降解菌的分离和鉴定

:从工业废水中分离到一株高效降解苯酚的菌株PHEA 2 ,它能够在以苯酚为单一碳源和能源的无机培养基上生长 ,其最高苯酚降解率为 394nmol/ (mg·min) .经Biolog细菌自动鉴定仪鉴定 ,该菌株为醋酸钙不动杆菌 (Acinetobactercalcoaceti cus) .采用PCR扩增获得的该菌 16SrDNA片段 ,核苷酸序列分析结果表明 ,该菌株的 16SrDNA的核苷酸序列与醋酸钙不动杆菌同源性为 98% .在细菌系统发育分类学上 ,PHEA 2归属变形细菌γ亚类、不动杆菌属、醋酸钙不动杆菌 .     

Effect of tracer dyes on initial deposits and persistence of bacillus thuringiensis subsp. kurstaki toxin after application of two commercial formulations onto spruce trees

Abstract

The effect of two tracer dyes [Erio Acid Red (EAR) and Acid Black 48 (AB‐48)] on initial deposits and persistence of Bacillus thuringiensis subsp. kurstaki (Btk) toxin (delta‐endotoxin) was studied after spraying two commercial formulations, Foray® 48B and Foray® 76B, over potted white spruce [Picea glauca (Moench) Voss] seedlings, at a dosage rate of 30 billion international units (BIU) per ha. Spray was applied using a spinning disc atomizer calibrated to deliver droplet sizes similar to those utilized in ultra‐low‐volume (ULV) treatments in operational insect control programs. The sprayed seedlings were left outdoors at the Sault Ste. Marie laboratory for 18 days under natural conditions of sunlight, wind and rainfall. Initial deposits and persistence of delta‐endotoxin protein in spruce foliage were determined by immunoassay [enzyme linked immunosorbent assay (ELISA)] quantification of the delta‐endotoxin. The total protein (inactive plus active) and delta‐endotoxin (active protein) concentrations in the two formulations were determined by a gravimetric procedure and by ELISA respectively.

The initial deposit levels of the toxin on foliage were not markedly affected by the addition of either of the two tracer dyes, and showed only a narrow range of 1521 to 1625 ng/g foliage (fresh weight) for Foray 48B, and 1789 to 2056 ng/g for Foray 76B. However, the persistence of the toxin was significantly influenced by the presence of the dyes. The toxin persisted in foliage only for 7 d post‐spray When the EAR dye was added to Foray 48B, compared to 10 d when no dye was added. The average half‐life (DT₅₀) of disappearance was 17.4 h for Foray 48B with EAR, and 20.9 h when no dye was present. In contrast, the situation was reversed in Foray 76B, since the duration of persistence was 10 d when EAR was added to Foray 76B, compared to 7 d when no dye was added. The average DT₅₀ was 27.9 h for Foray 76B with EAR, and 22.2 h without the dye. Persistence was the longest (14 d) when the AB‐48 dye was added to Foray 76B, and the DT₅₀ was 44.9 h.     

100% recycled hot mix asphalt: A review and analysis

A holistic evaluation of the feasibility of producing 100% recycled mixtures is presented. Eleven technologies readily available for producing 100% Reclaimed Asphalt Pavement (RAP) hot asphalt mixtures are described in the article and the complementary video (http://youtu.be/coj-e5mhHEQ). The recorded performance of 100% RAP mixtures is analyzed along with identification of typical high RAP distresses. Recommended mix design procedures and the best RAP management strategies are described. A cradle-to-gate analysis of environmental effects indicated 18 kg or 35% CO₂eq savings per t of produced 100% RAP asphalt mixture compared to virgin mix, while cost analysis showed at least 50% savings in material related expenses.     

Development and application of LC–APCI–MS method for biomonitoring of animal and human exposure to imidacloprid

Imidacloprid (IMI) is a relatively new neuro-active neonicotinoid insecticide and nowadays one of the largest selling insecticides worldwide. In the present study a LC–APCI–MS based method was developed and validated for the quantification of imidacloprid and its main metabolite 6-chloronicotinic acid (6-CINA) in urine and hair specimens. The method was tested in biomonitoring of intentionally exposed animals and subsequently applied for biomonitoring of Cretan urban and rural population.     

Thermal decomposition mechanism of 65% lysine sulfate powder and its thermal stability based on thermal analysis

Lysine is widely used in the fields of food, medicine and feed, which generally appears in the form of lysine sulfate or lysine hydrochloride dust because of the high instability of the free L-lysine. The L-lysine Sulfate is in high risk of decomposition, spontaneous ignition and even the dust explosion, because the control temperature in its production process is high up to 90 °C. Thus, the thermal behaviors and its thermal stability of 65% lysine sulfate are experimentally explored in Air and Nitrogen using the simultaneous TG-DSC measurements. Results show: (1) the decomposition of 65% lysine sulfate can be divided into three stages both in the atmospheres of air and nitrogen, and most of the weight loss occurred in the first two stages, which are related with the decarboxylation and deamination process. (2) The effects of atmosphere on the decomposition of 65% lysine sulfate mainly occur at the third stage. In this stage, the weight loss in nitrogen is only 14.2%, which is much lower than that in air (34.3%), which is related to the oxidative degradation at high temperature. Besides, the active energy is slightly increased in nitrogen compared to that in air. (3) The initial temperatures of the decomposition of the 65% lysine sulfate are 145 °C and 155 °C, for the air and nitrogen atmosphere, respectively, which are much lower than that (260 °C) of the pure lysine.     

水生生物对三唑磷的物种敏感度分布研究

针对水环境中日益严重的有机磷农药污染问题,选择广泛使用的三唑磷作为研究对象,利用其对水生生态系统中不同营养层次生物物种的半数效应浓度(median effective concentration, EC₅₀),建立了基于对数-逻辑斯蒂分布的水生生物物种敏感度分布(species sensitivity distribution, SSD)模型,并采用概率图和吻合度检验方法对该模型进行了检验和评价.结果表明,水生生物对三唑磷的 SSD 服从对数-逻辑斯蒂分布,其参数为 α=-0.4788±0.2381,β=0.7546±0.1078.基于该 SSD 模型,获得三唑磷的 5% 危害浓度(hazardous concentration for 5% of the species, HC₅)值为 1.992×10^-3 mg/L,并推导出三唑磷的最大浓度基准值(criteria maximum concentration, CMC)值为 9.96×10^-4 mg/L.对 HC₅、CMC 与单一物种的安全浓度的比较研究指出,基于 SSD 方法制定环境质量标准更为严格,也更接近于真实的生态环境.另外,根据渤海莱州湾海域中三唑磷的监测数据,预测了其对物种的潜在影响比例(potentially affected fraction, PAF)为 0.36%,对该水域生态环境的影响处于较低风险水平.     

活性炭吸附室内空气中挥发性有机化合物

活性炭吸附室内空气中挥发性有机化合物的１０％穿透时间与气相浓度及挥发性有机化合物的种类有关,通过对苯、甲苯和丙酮的实验研究,得出了由高浓度估算室内低浓度时炭床１０％穿透时间的经验公式ｔｂ,１＝ｔｂ,ｈ（Ｃ０,１／Ｃ０,ｈ）＾ａ,其中ａ值是与炭床性能及挥发性有机化合物种类有关的参数,可通过实验确定。     

Optimization of the recovery of plastics for recycling by density media separation cyclones

Material recovery processes are presented as the optimum option for recycling plastic wastes as a means of recovering hydrocarbon resources. There exist a large variety of automated material recovery processes for recycling of such wastes but each with significant limitations. Of these, the separation based on differences in densities is advocated as the optimum process either for producing recycled products or preparing wastes for subsequent recovery processing.Density separation processes based on cyclone type density media separation (DMS) is presented as an important, potential method for increasing plastics recycling process capacities. It is demonstrated to have the capacity to separate a significantly larger range of particle sizes than those presently processed industrially. The mathematical relationship for the prediction of quality of typical LARCODEMS type density media separations by particle size and density as expressed by the Ecart Probable is presented.A proposed device configuration is presented for density media separation to optimize the recovery and purity of both density fractions produced. It is also suggested that to be economically viable, a large scale of operation is required for industrial plastics recycling operations recovering and producing a number of different plastics with a purity to be used as a substitute for virgin material.     

微波诱导氧化处理雅格素红BF-3B150%染料废水的研究

以颗粒活性炭为催化剂 ,建立了微波诱导氧化工艺 ,对雅格素红BF 3B15 0 %染料废水进行了有效处理 .分别考查了废水初始浓度、微波功率、微波辐照时间、活性炭粒径、活性炭用量和废水pH值对废水处理效果的影响 .该工艺对稀释 10 0倍后的实际废水 (原水COD为 2 82 4 0mg·L-1)最佳处理工艺条件为 :微波辐照时间 6min、微波辐射功率 6 5 0W、活性炭用量为 8g、活性炭粒径 2 0目以下 ,微波诱导催化氧化在酸性条件下比在碱性条件下的处理效果要好 .在此工艺条件下 ,废水脱色率达99 6 %、COD去除率达 96 8% .微波辐射雅格素红染料废水脱色表观反应动力学研究表明 ,该反应近似一级反应 ,动力学常数为 0 735 1min-1,半衰期为 0 94min .微波诱导氧化、活性炭吸附和单纯微波辐射 3种不同工艺的对比实验表明 ,微波诱导氧化工艺具有明显的优越性 ,且不会对环境造成二次污染