机械强化污泥回流式一体化活性污泥法的运行机理研究

活性污泥通过机械搅拌强化污泥内循环回流,提高了污泥的活性,并且使污泥浓度可达到4.5kg/m3,用该机械强化污泥回流式一体化活性污泥法处理小区生活污水,当水力停留时间为3h,溶解氧为2.2mg/L,机械搅拌速度为250r/min时,CODcr、氨氮去除率均可达到83% 以上,出水达到国家污水排放一级标准.该一体化活性污泥法简单易行,运行成本低,投资小,操作维护方便,是生活小区生活污水适宜的处理工艺技术.     

污水处理厂污泥脱水滤液循环利用的研究

对污水处理厂污泥机械脱水滤液进行了循环利用研究。将滤液与剩余污泥（mlsss≤13000mg／l）按1比4的比例均匀混合。然后加入到沉淀器中进行重力浓缩试验，结果表明：它能够改善污泥的浓缩脱水性能，加快污泥的沉淀速度，增大浓缩污泥的浓度；生产运行数据分析显示：污泥脱水滤液与剩余污泥混合液进入浓缩池后，上清液更加清澈，污泥的固体负荷率显著提高，这既可降低污泥的处理成本，亦可减少污泥处理系统的基建投资，为污泥处理系统的工艺优化开辟了新途径。     

海水环境下玻璃纤维增强复合材料力学性能演化规律研究

目的 研究海水环境下海流能发电机组叶片用玻璃纤维复合材料力学性能的变化规律.方法 在实验室内通过海水浸泡试验、拉伸试验、弯曲试验以及剪切试验,测定叶片用玻璃纤维树脂基复合材料的吸水特性,以及在人工海水介质中各项力学性能参数的演变规律.结果 随着浸泡时间的增加,玻璃纤维树脂基复合材料吸水率先逐步增大、后趋于稳定,总吸水率约0.075％.抗拉强度呈先降低、后提高、又降低的趋势,抗拉强度最高可超过1100 MPa,最小值约为940 MPa.弹性模量和弯曲强度呈逐渐降低的趋势,弹性模量降幅约9.5％,弯曲强度降幅约为30％.弯曲模量变化起伏不定,变化幅度在15％以内.材料剪切强度呈先增大、后降低的趋势,最小值为189 MPa,较初始值高10 MPa.剪切模量呈先降低、后提高的现象,在浸泡28 d时,剪切模量最小,为16.4 GPa.结论 玻璃纤维增强树脂基复合材料经过长期海水浸泡后,拉伸及抗剪切性能略有降低,但降幅不大,抗弯性能下降明显,需要在叶片结构设计和强度计算时,充分考虑抗弯性能衰减的负面影响.     

Starch, Poly(lactic acid), and Poly(vinyl alcohol) Blends

Research on biodegradable materials has been stimulated due to concern regarding the persistence of plastic wastes. Blending starch with poly(lactic acid) (PLA) is one of the most promising efforts because starch is an abundant and cheap biopolymer and PLA is biodegradable with good mechanical properties. Poly(vinyl alcohol) (PVOH) contains unhydrolytic residual groups of poly(vinyl acetate) and also has good compatibility with starch. It was added to a starch and PLA blend (50:50, w/w) to enhance compatibility and improve mechanical properties. PVOH (M_W 6,000) at 10%, 20%, 30%, 40%, 50% (by weight) based on the total weight of starch and PLA, and 30% PVOH at various molecular weights (M_W 6,000, 25,000, 78,000, and 125,000 dalton) were added to starch/PLA blends. PVOH interacted with starch. At proportions greater than 30%, PVOH form a continuous phase with starch. Tensile strength of the starch/PLA blends increased as PVOH concentration increased up to 40% and decreased as PVOH molecular weight increased. The increasing molecular weight of PVOH slightly affected water absorption, but increasing PVOH concentration to 40% or 50% increased water absorption. Effects of moisture content on the starch/PLA/PVOH blend also were explored. The blend containing gelatinized starch had higher tensile strength. However, gelatinized starch also resulted in increased water absorption.     

某复合型地铁车站站台防排烟方案研究

在地铁站台火灾中，机械排烟和补风对于有效排出站台烟气至关重要，地铁设计规范要求采用正压送风方式来防止烟气经扶梯和楼梯流入站厅层。对于复合型地铁站台而言，站厅层可能与其它建筑共用，建筑面积较大，难以提供足够的风压进行正压送风。本文利用性能化防火设计方法对多种站台防排烟方案进行研究，并提出了分析流程。本文还针对某实际工程案例验证了这一流程的可行性，并据此选择了一种将机械排烟和补风有机结合的防排烟方案。本文的研究工作对其它类型地铁站台防排烟方案具有参考价值。     

Mechanical Properties with the Functional Group of Additives for Starch/PVA Blend Film

This paper deals with the mechanical properties and degree of swelling (DS) of starch/PVA blend film with the functional groups i.e., hydroxyl and carboxyl group, of additives. Starch/PVA blend films were prepared by using the mixing process. Glycerol (GL) with 3 hydroxyl group, sorbitol (SO) with 6 hydroxyl group, succinic acid (SA) with 2 carboxyl group, malic acid (MA) with 1 hydroxyl and 2 carboxyl group, tartaric acid (TA) with 2 hydroxyl and 2 carboxyl group and citric acid (CA) with 1 hydroxyl and 3 carboxyl group were used as additives. The results of measured tensile strength (TS) and elongation (%E) verified that both hydroxyl and carboxyl group as a functional groups increased the flexibility and strength of the film. Values of DS for GL-added and SA-added films were low. However, DS values of the films added MA, TA or CA with both hydroxyl and carboxyl group were comparatively high. When the film was dried at low temperature, the properties of the films were evidently improved. The reason is probably because the hydrogen bonding was activated at low temperature.     

分段变速加载对含瓦斯突出煤力学特性影响试验研究

为探究采动应力变化对含瓦斯突出煤力学特性的影响，利用RLW-500G煤岩三轴蠕变-渗流试验系统，对新景矿含瓦斯突出煤进行了不同围压和瓦斯压力下的常规三轴和分段变速加载力学试验。结果表明:煤样在2种应力路径下的全应力应变曲线均可分为压密、线弹性、塑性变形、应力跌落和残余应力5个阶段；随着围压的升高或者瓦斯压力的降低，煤体在2种应力路径下的强度和弹性模量均增大；相较于常规三轴，煤体在分段变速加载路径下的强度普遍增大，峰值轴向应变、峰值环向应变绝对值和峰值体积应变绝对值也普遍增大，失稳破坏瞬间应力跌落和能量释放更加剧烈。Mohr-Coulomb强度准则仍然适用于分段变速加载条件下的含瓦斯突出煤，该研究对于认识煤与瓦斯突出的发生机制具有一定的指导意义。     

某1000 MW燃煤机组脱硝催化剂运行性能检测

以某1000 MW燃煤机组脱硝系统使用的脱硝催化剂为研究对象，分别对不同运行时间的催化剂进行了对比检测。检测结果表明，运行初期，催化剂表面沉积了一定量的碱金属，但属于正常范围内；没有出现过多的硫化合物的沉积；催化剂微观结构遭到一定程度的破坏，比表面积有下降趋势；催化剂机械强度基本保持良好；催化剂活性衰减在正常范围内，催化剂可以继续使用或添加加装层。     

含疏松缺陷的ZL205A合金力学性能研究

目的获取含疏松缺陷ZL205A材料主要力学性能参数的变化规律及力学行为。方法通过单轴拉伸实验测试,采用割线法估算含不同等级疏松ZL205A试样的力学性能参数;基于试样断面及载荷-位移曲线分析,归纳ZL205A材料的力学行为,并通过有限元模拟对假设的力学模型进行验证。结果发现ZL205A材料的抗拉强度、伸长率、弹性模量及屈服强度指标呈现随疏松等级增加而降低的趋势,材料变形塑性屈服阶段不明显且具有脆性断裂特征。结论 Ramberg-Osgood方程适合于描述ZL205A材料的弹塑性本构关系。     

丁腈橡胶密封圈高温老化行为——自由状态和承压状态

目的研究丁腈橡胶密封圈自由状态和承压状态下的高温老化行为。方法以拉伸强度和拉断伸长率为参数,对各温度下的老化行为进行表征和分析。结果 70℃条件下机械应力大大加快了橡胶密封件拉伸强度的下降速率,以致试验64 d时拉伸强度甚至比110℃时还低,拉断伸长率的下降速率也明显加快了;90℃加速条件下机械应力对拉伸强度的下降有一定的促进作用,但对拉断伸长率的变化基本无影响;110℃加速条件下机械应力对拉伸强度和拉断伸长率均没有明显的影响。结论机械应力在较低温度下可以显著促进丁腈橡胶密封圈热氧老化,高温条件下促进作用不明显。