用煤矸石制取水玻璃的研究

本文研究了用煤矸石制取水玻璃的可行性，利用正交试验，研究了焙烧温度、焙烧时间、反应温度、ＮａＯＨ浓度、渣样粒度等因素对制取过程的影响，确定了最佳操作条件。     

碳素纤维在近岸海洋污染物磷酸盐、硅酸盐处理中的应用

对碳素纤维进行氧化改性,利用改性后的碳素纤维处理近岸污染海水,重点研究了改性碳素纤维对海水中活性磷酸盐和活性硅酸盐的吸附作用。考察了碳素纤维液相改性时间、碳素纤维投加量、活性磷酸盐初始浓度、活性硅酸盐初始浓度、吸附时间、海况、pH值等单因素对近岸海洋污染物磷酸盐、硅酸盐吸附效果的影响。研究结果表明:改性碳素纤维对硅酸盐的吸附效果较好,去除率可达70%,对活性磷酸盐的去除率为31%左右。通过正交实验确定改性碳素纤维材料修复模拟近岸海水的优化条件为:碳素纤维改性时间为1.5 h,投加量为0.01 g,硅酸盐初始浓度为3mg/L,磷酸盐初始浓度为20 mg/L,海况为3级,pH值为8,吸附时间为3 h。在此条件下,碳素纤维对磷酸盐的去除率可达31.06%,硅酸盐去除率可达70.88%。     

三峡水库三期蓄水前后长江口硅酸盐分布及其比值变化

河口SiO2--Si浓度的变化直接影响到水体的营养盐结构和生态系统.根据2010年8月、11月和2011年5月的现场调查资料,对长江口区域一个水文年(跨三峡水库三期蓄水)硅酸盐的分布特征和变化趋势进行了分析.结果表明,长江口及其邻近海域硅酸盐分布与盐度分布极其相似,整体呈现近岸高、外海低的特点;截取一断面分析发现存在上升流,硅酸盐等值线有抬升趋势.3个季节硅酸盐平面分布各有其季节性特点,但总体浓度夏季高于秋季,秋季高于翌年春季;在整个调查区域SiO32--Si/DIN值是10月＞8月＞5月,而SiO32--Si/PO43--P值是5月＞8月＞10月;3个季节SiO32--Si浓度与盐度都呈显著负相关关系.与历史资料比较得出,2010-2011年长江口海域营养盐比值小于2004年,也小于1985-1986年,可见三峡工程蓄水对长江口SiO32--Si/DIN、SiO32--Si/PO43--P降低的影响.     

Effects of seed aerosols on the growth of secondary organic aerosols from the photooxidation of toluene

Hydroxyl radical （.OH）-initiated photooxidation reaction of toluene was carried out in a self-made smog chamber. Four individual seed aerosols such as ammonium sulfate, ammonium nitrate, sodium silicate and calcium chloride, were introduced into the chamber to assess their influence on the growth of secondary organic aerosols （SOA）. It was found that the low concentration of seed aerosols might lead to high concentration of SOA particles. Seed aerosols would promote rates of SOA formation at the start of the reaction and inhibit its formation rate with prolonging the reaction time. In the case of ca. 9000 pt/cm^3 seed aerosol load, the addition of sodium silicate induced a same effect on the SOA formation as ammonium nitrate. The influence of the four individual seed aerosols on the generation of SOA decreased in the order of calcium chloride〉sodium silicate and ammonium nitrate〉ammonium sulfate.     

Preparation and coagulation efficiency of polyaluminium ferric silicate chloride composite coagulant from wastewater of high-purity graphite production

The aim of the present work was to produce a polyaluminium ferric silicate chloride (PAFSiC) coagulant from acidic and alkaline wastewater of purifying graphite by roasting, and subsequently to evaluate coagulation efficiency of the reagent by treating surface water from the Yellow River as well as municipal wastewater in comparison with the conventional coagulant polyaluminium chloride (PAC). The PAFSiC coagulant was prepared by co-polymerization. The effects of (Al+Fe)/Si molar ratio, OH/(Al+Fe) molar ratio (i.e., value), coagulant dosage and pH value of test suspension on the coagulation behavior of FAFSiC and the stability of the PAFSiC were also examined. Results showed that PAFSiC performed more efficiently than PAC in removing turbidity, chemical oxygen demand (COD), and total phosphate (TP). The PAFSiC with a value of 2.0 and (Al+Fe)/Si ratio of 5 (PAFSiC 2.0/5) showed excellent coagulation effect for both turbidity and COD, while PAFSiC 1.0/5 was the best for TP. The optimum coagulation pH range of PAFSiC 2.0/5 was 5.0–9.0, slightly wider than that of PAC (6.0–8.0). The process can be easily incorporated into high-purity graphite production plants, thereby reducing wastewater pollution and producing a valuable coagulant.     

应用于矿山修复的高效菌株鉴定与溶岩机制:基于增强回归树分析

岩石矿区废弃地水土流失问题极度严峻,微生物对修复该问题造成的退化生境具有重要意义,为探究微生物对岩石矿区生境修复的有效性与作用机制,采用两次定向筛选,获得1株高效产铁载体及吲哚乙酸(IAA)的硅酸盐矿物分解细菌,利用16S rRNA基因序列分析鉴定该细菌为Pseudomonas protegens.通过该细菌对硅酸盐岩的岩石分解实验,测定培养液pH值,K、Al、Si这3种元素的释放量,检测岩石溶蚀的粒径变化,并分析培养液中不同有机酸,氨基酸及多糖的浓度变化,研究Pseudomonas protegens NLX-4对硅酸盐的溶蚀效果,同时引入增强回归树(boosted regression tree analysis,BRT)分析,探究其促溶机制.分析表明,该细菌通过代谢积累一定浓度的酒石酸(777 mg·L~(-1))以及多糖(8.21 g·L~(-1)),对硅酸盐岩产生释钾、释铝、脱硅的作用,从而有效促进岩石的分解.菌株Pseudomonas protegens NLX-4可作为修复废弃矿地被破坏生境的良好菌种资源.     

基于白碳黑的水化硅酸钙制备及其磷回收特性简

以白碳黑、硅灰、硅藻土和硅胶筛选硅质原料，并与钙质原料电石渣制备了水化硅酸钙。借助XRF、BET、FTIR等表征手段，通过多次重复除磷实验，研究了硅质原料特性对水化硅酸钙回收磷性能的影响。结果表明，白碳黑具有极高的反应活性，因此可作为制备具有磷回收特性的水化硅酸钙的硅质原料。结合XRD等表征发现，白碳黑的有效利用率是影响水化硅酸钙回收磷性能的关键，该利用率取决于白碳黑与电石渣的摩尔配比以及水热反应温度。当电石渣与白碳黑的摩尔比为1.6：1，反应温度为170℃时，白碳黑具有最佳的利用效率。该条件制备的水化硅酸钙可作为晶种，在其表面结晶形成羟基磷灰石，从而达到磷回收的目的，磷回收后固体物质中的磷含量为19.05%。     

聚硅酸锌铝的制备及其性能研究

以硅酸钠、硫酸锌、硫酸铝为原料，通过共聚法制备了无机高分子絮凝剂聚硅酸锌铝（PSZAS），研究了Na₂SiO₃的摩尔浓度、活化时间、Al/Si、Zn/Si 配比及絮凝剂的投加量对絮凝效果的影响，用X-射线衍射（XRD）和电子扫描电镜（SEM）对该絮凝剂的结构及形貌进行了表征。结果表明：当硅酸钠的浓度为0.4 mol/L，硅酸活化时间为2 h，Si∶Al∶Zn=1∶1∶1.5，絮凝剂投加量为20 mL/L废水时，絮凝剂的电中和能力和吸附架桥能力最强，絮凝剂对含H-酸染料模拟废水的絮凝效果最好。     

多孔硅酸钙滤料吸附床除磷试验研究

以多孔硅酸钙滤料为吸附载体处理含磷的二沉池出水.通过静态吸附试验和动态吸附试验,研究了滤料粒径及投加量、初始pH、反应时间、温度以及滤料填充高度对除磷效果的影响.在静态吸附试验中,取初始磷质量浓度为4.98 mg/L的含磷废水100 mL,当多孔硅酸钙滤料粒径为4～14目,投加量为1.0g,吸附时间为2.5h,温度为25℃,溶液初始pH为7.0～9.0时,磷的去除率可达95％以上,出水磷满足《城镇污水处理厂污染物排放标准》(GB 18918-2002)的一级A标准(≤0.5 mg/L).动态吸附试验表明,在长期运行条件下,多孔硅酸钙滤料吸附床能持续有效地去除污水中的磷,综合考虑吸附率和运行费用,选择水力停留时间为30 min,滤料填充高度为60 cm为宜.     

Influences of Magnesium <Emphasis Type="Italic">tri-</Emphasis>Silicate on the Physical,Mechanical, and Degradable Properties of Ultraviolet (UV) Radiation Cured Plain Board Surface

A series of formulations were prepared with different percentages of oligomer, epoxy diacrylate (EA-1020 ), monomer, 1,6 Hexane diol diacrylate,(HDDA) and different percentages of filler (Magnesium tri-silicate, Mg₂Si₃O₈). Irgacure 369 [2-Benzyl-2-dimethyl-amine-1 (4-morpholinophenyl) butanone-1] was used in the formulations as photoinitiator. Ultraviolet (UV) cured thin polymer films were prepared from these formulating solutions on clean glass plates. Pendulum hardness (PH), gel content and macro scratch hardness (MSH) of the UV cured films were studied. One percent Mg₂Si₃O₈ containing formulation showed the premium properties. The substrates (plain board) were coated by these formulating solutions and cured under the same UV lamp at different intensities of radiation. Various properties of the coated surface such as PH, gloss, adhesion, abrasion and MSH were investigated. The base coat containing 1% Mg₂Si₃O₈ and top coat containing 48% HDDA produced the best performance among all the formulations inspected. The degradable properties in different weathering conditions on PH, gloss, adhesion, abrasion and MSH were measured. The surface cured with the optimized formulation (E) again yielded the minimum loss of the properties.