车门框条滚压成形工艺及滚压线设计

以X110型车门为例,分析零件工艺性,介绍滚压成形工艺过程,强调在模具设计和制作中应注意的问题。设计由滚压、校正、滚焊和自动断料等工艺流程组成的滚压线,可作为类似滚压工艺参考。     

Human appropriation of net primary production as determinant of avifauna diversity in Austria

The relationship between land-use induced changes in production ecology and avifauna diversity was analysed using a GIS land cover dataset on a 0.25 km × 0.25 km grid covering Austria's national territory. Considering only aboveground processes, the “human appropriation of net primary production” (HANPP = potential NPP − NPP_t), actual NPP (NPP_act), harvest (NPP_h) and NPP_t (= NPP_act − harvest) were recalculated based on existing datasets. Elevation as well as indicators of land cover heterogeneity and landscape heterogeneity were also considered. Correlation analyses were performed between these potential determinants of avifauna diversity and breeding bird species richness data as well as the percentage of endangered breeding birds included in the Austrian red list. Four spatial scales—0.25 km × 0.25 km, 1 km × 1 km, 4 km × 4 km and 16 × 16 km, were analysed. It was shown that breeding bird species richness was more strongly correlated with production ecological indicators and elevation than with heterogeneity indicators. A residual analysis in which the effect of elevation (a proxy for climate) on species richness and its potential determinants was removed confirmed the importance of the availability of trophic energy (NPP) for bird diversity patterns. The results support the species-energy hypothesis, thus confirming the notion that HANPP could be a useful pressure indicator for biodiversity loss.     

压盖落料冲孔成形模设计

介绍了在尺寸公差及形位公差要求较高的落料冲孔成形件的模具设计过程中，不降低劳动效率的情况下，如何使模具简化、降低模具成本，并使冲压件满足其设计要求。     

环境承载力与环境扶贫

随着人类环境意识的觉醒与升华，引发了对自身生存环境的更深层次的思考。本文就环境承载力的内涵与外延以及它既会造成贫困又可解脱贫困的关键作用进行了研究和探讨。     

磷肥厂烘干磨高压静电除尘技术及应用

本文根据高压静电除尘的原理,磷肥厂烘干磨粉尘的特性分析,以及作者本人的工作实践,探讨了高压静电除尘技术在磷肥厂烘干磨粉尘治理中应用的可行性。     

On the thermal rupture of 1.9 m propane pressure vessels with defects in their thermal protection system

This paper describes the results from a series of fire tests that were carried out to measure the effect of defects in thermal protection systems on fire engulfed propane pressure vessels.

In North America thermal protection is used to protect dangerous goods rail tank-cars from accidental fire impingement. They are designed so that a tank-car will not rupture for 100 min in a defined engulfing fire, or 30 min in a defined torching fire. One common system includes a 13 mm blanket of high-temperature ceramic fibre thermal insulation covered with a 3 mm steel jacket. Recent inspections have shown that some tanks have significant defects in these thermal protection systems. This work was done to establish what levels of defect are acceptable from a safety standpoint.

The tests were conducted using 1890 l (500 US gallon) ASME code propane pressure vessels (commonly called tanks in the propane industry). The defects tested covered 8% and 15% of the tank surface. The tanks were 25% engulfed in a fire that simulated a hydrocarbon pool fire with an effective blackbody temperature of 870 °C.

The fire testing showed that even relatively small defects can result in tank rupture if the defect area is engulfed in a severe fire, and the defect area is not wetted by liquid from the inside. A wall failure prediction technique based on uniaxial high-temperature stress rupture test data has been developed and agrees well with the observed failure times.     

南京理工大学高压实验室及其研制高压水射流切割机

南京理工大学高压实验室自８０年代初建立以来，在高压容器及武器发射管的自紧理论和工程应用、高压零部件研制、高压传感器和信号放大显示系统、高压介质等方面做了大量的工作。９３年以来，进行了水射流切割机的研制工作，解决了超高压缸体的动态密封、高压缸体的自增强、无触点式换向传感器、内衬不锈钢组合型高压容器等诸多问题，试制成功了水射流切割机样机。     

均压防灭火定量分析技术研究及其应用

均压是防治煤矿自然发火的主要措施之一。针对均压应用中的定性分析方法及两点式均压方法的不足,提出了均压防灭火定量分析技术并开发了与采空区相连两个工作面间均压的计算机摸拟计算程序。阐述了程序均压原理、内容及应用实例。这项技术具有创新性和应用推广价值,可以提高均压防灭火技术应用的经济性和安全性     

带防腐层在役压力容器表面磁粉探伤灵敏度的试验研究

采用人工裂纹试样的方法 ,模拟压力容器涂刷油漆防腐层的状况进行磁粉探伤 ,得出了油漆防腐层厚度与裂纹检出灵敏度的定量关系 ;结合CVDA《压力容器缺陷评定》规范 ,探讨了试验方法对一般在役压力容器带有油漆的情况下 ,进行磁粉探伤检验的可行性。研究表明 :采用交流磁化法进行探伤 ,当漆层厚度大约小于2 5 0 μm时 ,灵敏度影响较小 ,同时亦表明不宜使用直流磁化方法。该结论对承受低应力工况条件下的压力容器安全质量检验和评估 ,具有重要参考价值     

Flame behaviors and pressure characteristics of vented dust explosions at elevated static activation overpressures

Dust explosion venting experiments were performed using a 20-L spherical chamber at elevated static activation overpressures larger than 1 bar. Lycopodium dust samples with mean diameter of 70 μm and electric igniters with 0.5 KJ ignition energy were used in the experiments. Explosion overpressures in the chamber and flame appearances near the vent were recorded simultaneously. The results indicated that the flame appeared as the under-expanded free jet with shock diamonds, when the overpressure in the chamber was larger than the critical pressure during the venting process. The flame appeared as the normal constant-pressure combustion when the pressure venting process finished. Three types of venting processes were concluded in the experiments: no secondary flame and no secondary explosion, secondary flame, secondary explosion. The occurrence of the secondary explosions near the vent was related to the vent diameter and the static activation overpressure. Larger diameters and lower static activation overpressures were beneficial to the occurrence of the secondary explosions. In current experiments, the secondary explosions only occurred at the following combinations of the vent diameter and the static activation overpressure: 40 mm and 1.2 bar, 60 mm and 1.2 bar, 60 mm and 1.8 bar.