Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

肥煤自燃全过程热动力学特征参数研究

实验测定了林西矿肥煤样品30~900℃煤自燃全过程热动力学特征参数,得出:TG/DTG曲线显示煤样DTG初始临界温度45℃,干裂温度122℃,活性温度195℃,增速温度265℃,质量极大值温度342℃,着火温度465℃,最大热失重速率温度515℃和燃尽温度690℃;DSC曲线显示,煤样初始放热温度60℃、最大热释放速率温度511℃。结合TG-DTG-DSC曲线综合分析可知,煤温达到510℃左右时煤样反应最剧烈。由煤自燃标志气体测定实验系统得出:煤温130℃后CO,CO 2释放量迅速增加,210℃增加速度下降;CH 4,C 2 H 6含量变化具有规律性且两者变化相近;C 2 H 4出现温度为130℃;C 2 H 4/C 2 H 6比值在190~350℃有较强的规律性,呈上升趋势且上升速度较快;350℃之后,CH 4,C 2 H 6,C 2 H 4体积分数均开始急剧增大;C 2 H 4/CO与C 2 H 4/CO 2变化趋势大致相同,在130~350℃时缓慢增长,达到350℃后比值呈指数形式上升。经拟合曲线,得到活化能的3个突变点温度:70,180,220℃,其中180℃与交叉点温度相吻合。通过以上研究,得到了肥煤自燃全过程的热力学特征参数,为实际生产中防治煤自燃提供了理论依据。     

过一硫酸盐的活化及其降解水中有机污染物机理的研究进展

基于活化过一硫酸盐（PMS）产生SO₄^-·的新型高级氧化技术,在芬顿和类芬顿催化降解水中有机污染物的研究中占有重要地位。本文从活化PMS方法的特点和用途出发,对目前活化PMS的主要方法进行了论述,并对活化PMS降解水中有机污染物的机理进行了探讨,最后对该领域研究中存在的问题进行了分析。指出,开发高效的协同活化PMS的方法将成为该领域研究的必然趋势。     

单轴应力对煤自燃特性参数和导热系数的影响研究

为探究单轴应力作用下煤氧化和传热特性，利用自制荷载加压煤自燃特性参数测定装置对炉体内长焰煤煤样进行程序升温。结合程序升温过程中煤临界温度Tc和Tg，对其进行阶段划分:阶段1为30℃~Tc；阶段2为Tc~Tg。计算了不同单轴应力下2个阶段煤表观活化能和平均耗氧速率。根据能量守恒得出程序升温过程煤导热系数随温度的变化，进一步分析煤导热系数与单轴应力的关系。结果表明:阶段1单轴应力为4 MPa时为临界轴压，煤表观活化能最大，平均耗氧速率最小；阶段2煤表观活化能和平均耗氧速率随单轴应力增大均呈抛物线变化，单轴应力为2.7 MPa时为临界轴压，煤表观活化能最大，平均耗氧速率最小；阶段1和2煤导热系数随温度升高均先减小后增大，并且煤导热系数随单轴应力增大呈三次函数变化。     

废弃混凝土对C_3S形成动力学的影响

废弃混凝土中石灰石的含量比较稳定,适合取代天然石灰石作为钙质原料配制水泥生料,并含有少量的SiO2,可以起部分硅质原料的作用。硬化的水泥浆体在高温下脱水形成氧化钙、氧化铝和氧化铁等氧化物,都是制造水泥所必须的氧化物。实验室利用20%和40%的废弃混凝土代替部分石灰石制备水泥熟料。研究了废弃混凝土对硅酸盐水泥熟料形成动力学的影响。用快速滴定法测定了不同熟料中f-CaO含量,根据文章提出CaO反应生成C3S的转化率,并用Amhenius公式计算了熟料中C3S形成反应的表观活化能。研究表明:废弃混凝土能改善生料的易烧性,并能降低熟料的烧成温度。     

污泥基活性炭的制备、表征及其应用

以城市生活污水厂脱水车间污泥为原料,采用化学活化法(ZnCl2为活化剂)在活化剂浓度为45%、活化温度为600℃、浸渍温度为45℃、活化时间为50min条件下制备污泥基活性炭。对污泥基活性炭进行了孔结构、扫描电镜(SEM)、红外光谱(FTIR)、XRD等表征分析。结果表明:该条件下制备出的污泥基活性炭碘吸附值为427.51mg/g,比表面积为329.48m2/g,大孔、中孔、微孔容积分别为0.19,0.12,0.15cm3/g。平均孔径为3.953nm。将其应用于生活污水处理,考察了污泥基活性炭投加量、pH、吸附时间对其吸附性能的影响。     

铅在棉秆基活性炭上的吸附动力学与热力学

以棉秆与棉秆纤维为原料,利用磷酸活化法制备了低成本的高比表面微孔棉秆基活性炭,通过静态实验研究了活性炭对水溶液中铅的吸附特性,测定了溶液pH值、吸附时间、溶液温度对吸附的影响,探讨了吸附动力学、热力学及吸附机制.根据低温液氮(N2/77K)吸附测定数据,以BET方程、BJH法及H-K法对活性炭孔结构进行了表征,以Boehm滴定、FTIR、零电荷点pHPZC测定及元素分析定量表征活性炭表面含氧官能团.结果表明,以棉秆和棉秆纤维为原料制备的活性炭的比表面积分别为1570和1731m2·g-1,含氧酸官能团含量分别为1.43和0.83mmol·g-1,均高于商业活性炭ST1300.静态吸附实验表明,棉秆基活性炭对铅有较大的吸附容量和吸附效率,最大吸附量超过120mg·g-1,溶液pH对吸附有较大的影响,吸附量随时间增大而增大,在5min内可达饱和吸附量的80%;吸附动力学数据符合假二级方程,Freundlich方程能更好地描述等温吸附行为;热力学研究表明,吸附吉布斯自由能(ΔG0)0,而焓变(ΔH0)0,说明吸附为吸热的自发反应过程,升温有利于吸附,离子交换可能在吸附过程中起了重要作用.     

Antimicrobial activity of thin metallic silver flakes, waste products of a manufacturing process

The aim of the research was to develop new products and processes from a manufacturing waste from an Italian metallurgic company. The company produced thin silver metallic films and the production scraps were silver flakes. The possibility to use the silver flakes in water disinfection processes was studied. The antimicrobial activity of the flakes was investigated in batch using Escherichia coli as Gram-negative microorganism model. The flakes did not show any antimicrobial activity, so they were activated with two different processes: thermal activation in reducing atmosphere and chemical activation, obtaining, respectively, reduced flakes (RF) and chemical flakes (CF). The flakes, activated with either treatment, showed antimicrobial activity against E. coli. The kill rate was dependent on the type of activated flakes. The chemical flakes were more efficient than reduced flakes. The kill rate determined for 1 g of CF, 1.0 ± 0.2 min⁻¹, was greater than the kill rate determined for 1 g of RF, 0.069 ± 0.004 min⁻¹. This was confirmed also by the minimum inhibitory concentration values. It was demonstrated that the antimicrobial capability was dependent on flakes amount and on the type of aqueous medium. Furthermore, the flakes maintained their properties also when used a second time. Finally, the antimicrobial activities of flakes were tested in an effluent of a wastewater treatment plant where a variety of heterotrophic bacteria were present.     

微波酸活化粉煤灰吸附酸性大红染料废水实验研究

以微波酸活化改性后的粉煤灰为吸附剂,对酸性大红染料废水进行吸附脱色处理,考察了吸附时间、pH值、吸附剂投加量等对吸附脱色效果的影响。在酸性大红染料溶液初始浓度为100 mg/L、pH=5、活化粉煤灰投加量为10 g/L吸附1 h时,活化粉煤灰对酸性大红的脱色效果较好,去除率可达96%。对实验数据进行相关数学模型拟合,结果表明微波酸活化改性后的粉煤灰吸附去除酸性大红的等温吸附平衡符合Langmuir吸附等温式,改性前后的吸附过程动力学符合准二级吸附动力学模型,线性相关系数良好。     

三峡库区典型流域水华暴发评价函数模型研究

藻类在光照充足时将无机磷酸和ADP转化为ATP以储备能量,外部条件改变时,则ATP可逆转换为ADP以释放能量.在此理论框架下根据三峡库区典型流域水华暴发时的现场监测数据研究了绿藻光合磷酸化的活化能ΔE、计算了库区流域中若干水系在不同水文条件下提供的有效能量Δe和综合营养指数TLI(Σ),并以ΔE、Δe和TLI(Σ)为参数构建了预测和判断不同水域环境中水华是否暴发的水华暴发评价函数F,在考虑外部因素和内部因素对水华暴发影响程度的大量计算和分析的基础上,确定了ΔE、Δe和TLI(Σ)的相关权重分别为a₁=0.3,a₂=0.3,a₃=0.4.模型计算和实地验证表明:F比单纯的TLI(Σ)作为水华暴发或者水体富营养化的判据更合理,更有说服力和更具普适性.