Applicability of a sharp-interface model for estimating steady-state salinity at pumping wells--validation against sand tank experiments

A numerical sharp-interface model of saltwater and freshwater behavior was validated against experiments conducted in two small scale sand tanks. A simple algorithm was proposed to determine saltwater and freshwater withdrawal rates at a pumping well at which a total pumping rate was specified. Model estimates were compared with transient salinity breakthroughs and steady-state salinities of water extracted from pumping wells in the sand tanks. Experimental scenarios included various combinations of freshwater pumping and injection and saltwater pumping. The corresponding Nash-Sutcliffe model efficiency was 0.95, which showed that the agreement between observations and computed results was satisfactory.     

Toxic effects of Hydrilla verticillata exposed to toluene, ethylbenzene and xylene and safety assessment for protecting aquatic macrophytes

Little information is available about the toxicity of toluene, ethylbenzene and xylene acting on macrophytes, and their toxicity data are rarely used in regulation and criteria decisions. The results extended the knowledge on toxic effects of toluene, ethylbenzene and xylene on aquatic plants. The responses of Hydrilla verticillata to these pollutants were investigated. Chlorophyll levels, lipid peroxidation, and antioxidant enzymes (superoxide dismutase and guaiacol peroxidase) showed diverse responses at different concentrations of toluene, ethylbenzene and xylene. The linear regression analyses were performed respectively, suggesting the concentrations of toluene, ethylbenzene and xylene expected to protect aquatic macrophytes were 7.30 mg L⁻¹, 1.15 mg L⁻¹ and 2.36 mg L⁻¹, respectively. This study emphasized that aquatic plants are also sensitive to organic pollutants as fishes and zooplanktons, indicating that macrophytes could be helpful in predicting the toxicity of these pollutants and should be considered in regulation and criteria decisions for aquatic environment protection.     

Modeling VOC-odor exposure risk in livestock buildings

This paper describes a novel idea of linking models of exposure, internal dosimetry, and health effects. Risk assessment approach that integrates predicted odor caused by volatile organic compounds (VOC-odor) of toluene/xylene concentrations in human tissues leads to predict exposure risks in livestock buildings. First, VOC transport model was developed to calculate airborne toluene/xylene concentrations. Based on a physiologically based pharmacokinetic (PBPK) model, concentrations within five compartments representing lung, liver, fat, slowly perfused tissues, and rapidly perfused tissues could be quantified. By using a pharmacodynamic (PD) Hill model, we can optimally fit data from rat and human experiments to reconstruct dose-response relationships for accounting human health effects from nose poke and eye irritation. Results demonstrated that peak tissue concentration occurring at 5-10h in that fat contains the highest concentration than other tissues at around 4ppm of toluene and 1.8ppm of xylene. The EC(10) values are 114 and 232ppm, whereas expected risks are estimated to be 0.71% and 0.26% of human exposure to toluene and xylene, respectively. Risk analyses indicate that inhalation exposure in livestock buildings poses no significant threat to human health under the present environmental conditions. This method provides a rigorous and effective approach to relate target tissue concentration to human nose poke or eye irritation. We suggest that our probabilistic framework and methods be taken seriously because they produce general conclusions that are more robust and could offer a risk-management framework for discussion of future establishment of limits for respiratory exposure to VOC-odor.     

The variability and intrinsic remediation of a BTEX plume in anaerobic sulphate-rich groundwater

Data from long-term groundwater sampling, limited coring, and associated studies are synthesised to assess the variability and intrinsic remediation/natural attenuation of a dissolved hydrocarbon plume in sulphate-rich anaerobic groundwater. Fine vertical scale (0.25- and 0.5-m depth intervals) and horizontal plume-scale (>400 m) characteristics of the plume were mapped over a 5-year period from 1991 to 1996. The plume of dissolved BTEX (benzene, toluene, ethylbenzene, xylene) and other organic compounds originated from leakage of gasoline from a subsurface fuel storage tank. The plume was up to 420 m long, less than 50 m wide and 3 m thick. In the first few years of monitoring, BTEX concentrations near the point of leakage were in approximate equilibrium with non-aqueous phase liquid (NAPL) gasoline. NAPL composition of core material and long-term trends in ratios of BTEX concentrations in groundwater indicated significant depletion (water washing, volatilisation and possibly biodegradation) of benzene from residual NAPL after 1992. Large fluctuations in BTEX concentrations in individual boreholes were shown to be largely attributable to seasonal groundwater flow variations. A combination of temporal and spatial groundwater quality data was required to adequately assess the stationarity of plumes, so as to allow inference of intrinsic remediation. Contoured concentration data for the period 1991 to 1996 indicated that plumes of toluene and o-xylene were, at best, only partially steady state (pseudo-steady state) due to seasonal groundwater flow changes. From this analysis, it was inferred that significant remediation by natural biodegradation was occurring for BTEX component plumes such as toluene and o-xylene, but provided no conclusive evidence of benzene biodegradation. Issues associated with field quantification of intrinsic remediation from groundwater sampling are highlighted. Preferential intrinsic biodegradation of selected organic compounds within the BTEX plume was shown to be occurring, in parallel with sulphate reduction and bicarbonate production. Ratios of average hydrocarbon concentrations to benzene for the period 1991 to 1992 were used to estimate degradation rates (half-lives) at various distances along the plume. The estimates varied with distance, the narrowest range being, for toluene, 110 to 260 days. These estimates were comparable to rates determined previously from an in situ tracer test and from plume-scale modelling.     

Estimation of volatile organic compounds in Kuwaiti houses after the Gulf war

Interest in indoor air quality is steadily increasing. Exposure to volatile organic compounds (VOCs) is associated with health effects as diverse as childhood respiratory disease, lung cancer and cardiovascular disease. In an effort to assess the environmental impact indoors from possible sources of VOCs, such as (i) open oil lakes, (ii) chemical and petrochemical industries and (iii) indoor pollution from household items, concentrations of aliphatic and aromatic VOCs, comprising n-hexane to n-hexadecane, benzene, toluene, xylene, ethyl benzene, methanol and o-dichlorobenzene, were measured in indoor air samples from seven different cities in Kuwait using a gas chromatograph. The data for the period March to May 1993 are presented. The VOCs, as measured, were surprisingly low and they are below the concentrations set by the American Hygienists Association. However, although the concentration of the estimated VOCs being low, were cumulative effects of them entering the human body and water sources cannot be ruled out.     

Field method comparison between passive air samplers and continuous monitors for Vocs and NO2 in El Paso, Texas

This study evaluates the performance of Model 3300 Ogawa Passive Nitrogen Dioxide (NO2) Samplers and 3M 3520 Organic Vapor Monitors (OVMs) by comparing integrated passive sampling concentrations to averaged hourly NO2 and volatile organic compound (VOC) measurements at two sites in El Paso, TX. Sampling periods were three time intervals (3-day weekend, 4-day weekday, and 7-day weekly) for three consecutive weeks. OVM concentrations were corrected for ambient pressure to account for higher elevation. Precise results (< 5% relative standard deviation, RSD) were found for NO2 measurements from collocated Ogawa samplers. Reproducibility was lower from duplicate OVMs for BTEX (benzene, toluene, ethylbenzene, and xylene isomers) VOCs (> or = 77% RSD for 2-day samples) with better precision for longer sampling periods. Comparison of Ogawa NO2 samplers with chemiluminescence measurements averaged over the same time period suggested potential calibration problems with the chemiluminescence analyzer. For BTEX species, generally good agreement was obtained between OVMs and automated-gas chromatograph (auto-GC) measurements. The OVMs successfully tracked increasing levels of VOCs recorded by the auto-GCs. However, except for toluene, OVM BTEX measurements generally exceeded their continuous counterparts with a mean bias of 5-10%. Although interpretation of the study results was limited due to small sample sizes, diffusion barrier influences caused by shelters that housed OVMs and differences in sampling heights between OVMs and auto-GC inlet may explain the overestimation.     

C2–C10 nonmethane hydrocarbons measured in Dallas,USA—Seasonal trends and diurnal characteristics

Nonmethane hydrocarbons (NMHCs) are important precursors of ozone and other photo oxidants. We presented continuous hourly average concentrations of 45 C₂–C₁₀ NMHCs measured in urban area of Dallas, USA from 1996 to 2004. Most of the selected compounds are good variables with less noise. The top 10 species with high ozone-generating potential were identified according to their concentrations and reactivities. The ambient concentrations of abundant anthropogenic emission hydrocarbons measured in Dallas were about 2–4 times of the background values measured in the remote areas with adjacent latitude. The time series for anthropogenic emission hydrocarbons showed an obvious seasonal cycle with relatively high concentration in winter and low concentration in summer. The sinusoidal function with a linearly decreasing factor could well fit the time series of NMHCs. The phase of seasonal cycle for the aromatic hydrocarbons of toluene, m/p xylene and o-xylene that might come from both vehicle emission and solvent utilities evaporation was about 1 month earlier than that for alkanes and alkenes that mainly came from vehicle emission. Ambient NMHCs in Dallas decreased with a stable rate during 1996–2004. For most of compounds with high ozone-generating potential, the rate of ambient concentration decrease was higher or much higher than the rate of volatile organic compounds (VOCs) source emission reduction estimated by EPA's National Emission Inventory. On weekdays, the morning hydrocarbon concentration peak was coincident with morning traffic rush time in Dallas. Another concentration peak was delayed to afternoon traffic rush time. The characteristics of VOCs sources, photochemical removal processes and atmospheric dilution could be interpreted by the diurnal variations of benzene/ethylbenzene (B/E), toluene/ethylbenzene (T/E) and xylene/ethylbenzene (X/E). The ratio of VOC/NO_x measured in Dallas was substantially smaller than that calculated for USA cities. Ozone formation in Dallas was VOC sensitive.     

Removal ratio of gaseous toluene and xylene transported from air to root zone via the stem by indoor plants

This work was designed to investigate the removal efficiency as well as the ratios of toluene and xylene transported from air to root zone via the stem and by direct diffusion from the air into the medium. Indoor plants (Schefflera actinophylla and Ficus benghalensis) were placed in a sealed test chamber. Shoot or root zone were sealed with a Teflon bag, and gaseous toluene and xylene were exposed. Removal efficiency of toluene and total xylene (m, p, o) was 13.3 and 7.0 μg·m^?3·m^?2 leaf area over a 24-h period in S. actinophylla, and was 13.0 and 7.3 μg·m^?3·m^?2 leaf area in F. benghalensis. Gaseous toluene and xylene in a chamber were absorbed through leaf and transported via the stem, and finally reached to root zone, and also transported by direct diffusion from the air into the medium. Toluene and xylene transported via the stem was decreased with time after exposure. Xylene transported via the stem was higher than that by direct diffusion from the air into the medium over a 24-h period. The ratios of toluene transported via the stem versus direct diffusion from the air into the medium were 46.3 and 53.7 % in S. actinophylla, and 46.9 and 53.1 % in F. benghalensis, for an average of 47 and 53 % for both species. The ratios of m,p-xylene transported over 3 to 9 h via the stem versus direct diffusion from the air into the medium was 58.5 and 41.5 % in S. actinophylla, and 60.7 and 39.3 % in F. benghalensis, for an average of 60 and 40 % for both species, whereas the ratios of o-xylene transported via the stem versus direct diffusion from the air into the medium were 61 and 39 %. Both S. actinophylla and F. benghalensis removed toluene and xylene from the air. The ratios of toluene and xylene transported from air to root zone via the stem were 47 and 60 %, respectively. This result suggests that root zone is a significant contributor to gaseous toluene and xylene removal, and transported via the stem plays an important role in this process.     

Biofiltration of gasoline vapor by compost media

Gasoline vapor was treated using a compost biofilter operated in upflow mode over 4 months. The gas velocity was 6 m/h, yielding an empty bed retention time (EBRT) of 10 min. Benzene, toluene, ethylbenzene and xylene (BTEX) and total petroleum hydrocarbon (TPH) removal efficiencies remained fairly stable approximately 15 days after biofilter start-up. The average removal efficiencies of TPH and BTEX were 80 and 85%, respectively, during 4 months of stable operation. Biodegradation portions of the treated TPH and BTEX were 60 and 64%, respectively. When the influent concentration of TPH was less than 7800 mg TPH/m3, approximately 50% of TPH in the gas stream was removed in the lower half of the biofilter. When the influent concentration of BTEX was less than 720 mg BTEX/m3, over 75% of BTEX in the gas stream was removed in the lower half of the biofilter. Benzene removal efficiency was the lowest among BTEX. A pressure drop could not be detected over a 1-m bed height at a gas velocity of 6 m/h after approximately 4 months of operation. Results demonstrated that BTEX in gasoline vapor could be treated effectively using a compost biofilter.     

Chronic toxicity of tributyltin to development and reproduction of the European freshwater snail Lymnaea stagnalis (L.)

Chronic toxicity, growth and reproduction were measured in the freshwater gastropod Lymnaea stagnalis exposed to waterborne bis(tri-n-butyltin) oxide (TBTO) over a range of four nominal concentrations (0-10microg TBTl(-1)). Egg development was completely inhibited at 10microg TBTl(-1), whilst abnormal embryonic development was observed at 1microg TBTl(-1). For the solvent control and the 0.01microg TBTl(-1)treatment group, normal development of L. stagnalis was observed. Survivorship of hatchlings was significantly reduced by TBT at 1microgl(-1) while inhibition of shell growth of L. stagnalis was also observed at this concentration. The data were used to determine intrinsic growth rates (r) using two theoretical approaches (the Euler-Lotka equation and a Leslie Matrix). Both approaches showed that survival, fecundity and population growth rate were reduced at 1microg TBTl(-1). Interestingly, at 0.01microg TBTl(-1) snails showed a higher fecundity and growth rate than in the solvent control. The TBT concentration at which the r would equal zero (ECr(0)) and the population NOEC (No Observed Effect Concentration) were estimated. The population NOEC was defined as either the lower 95% confidence or lower 95% pointwise percentile limit of the ECr(0). Values obtained using the two different approaches were similar and thus a geometric mean was calculated to obtain a final representative population NOEC value for L. stagnalis of 2745ng TBTl(-1). The present data together with chronic toxicity TBT data for freshwater organisms, obtained from peer-reviewed literature, were used to construct a species sensitivity distribution (SSD). A predicted no effect concentration was then derived from the SSD (hazardous concentration at 5%, i.e., HC5 or 95% protection level). This SSD was compared with the SSD derived from saltwater species datasets. The HC5 value for saltwater species (3.55ng TBTl(-1); lower confidence limit: 1.93ng TBTl(-1)) was significantly lower than that for freshwater species (30.13ng TBTl(-1); lower confidence limit: 9.23ng TBTl(-1)), indicating that saltwater species are probably more susceptible to TBT than their freshwater counterparts.     

Viability of natural attenuation in a petroleum-contaminated shallow sandy aquifer

This study focused on evaluating and quantifying the potential of natural attenuation of groundwater at a petroleum-contaminated site in an industrial area of a satellite city of Seoul, Korea. Groundwater at the study site was contaminated with toluene, ethylbenzene and xylene (TEX). Eight rounds of groundwater sampling and subsequent chemical analyses were performed over a period of 3 years. The groundwater quality data suggests that TEX concentrations at this site have been decreasing with time and that the TEX plume is at a quasi-steady state. Trend analysis, changes in mass flux and plume area also confirmed that the TEX plume has reached a quasi-steady state. The proportion of the total attenuation attributable to biodegredation has decreased over the monitoring period while contribution of other attenuating processes, such as dilution or dispersion, has increased. Based on the calculated attenuation rates, it would take more than 20 years to clean up the site by natural attenuation alone.     

Removal characteristics of trace compounds of landfill gas by activated carbon adsorption

The removal characteristics of trace compounds and moisture in raw landfill gas (LFG) were studied. The LFG from the extraction well was saturated with water and moisture was eliminated by physical methods including cyclone-type dehydrator and compressor. The moisture removal efficiency of dehydrator and compressor was above 80%. As the moisture contents of LFG decreased, the toxic compounds like aromatics and chlorinated compounds were effectively removed by using the granular activated carbon. The breakthrough time and adsorption capacity of benzene, toluene, and ethyl benzene decreased rapidly when the relative humidity is over 60%. The effect of moisture was more pronounced at lower adsorbate concentrations tested than at higher concentrations. The breakthrough curves for multi-component mixtures show displacement effects. In the course of competing adsorption, adsorbates with strong interaction force to displace weakly bounded substances. Adsorption by activated carbon is in descending order of xylene, ethylbenzene, toluene, tri or tetrachloroethylene, benzene, carbon tetrachloride and chloroform in LFG, respectively.     

Effect of ageing on the availability of heavy metals in soils amended with compost and biochar: evaluation of changes in soil and amendment properties

Remediation strategies using soil amendments should consider the time dependence of metal availability to identify amendments that can sustainably reduce available pollutant concentrations over time. Drying-wetting cycles were applied on amendments, soils and soil + amendment mixtures, to mimic ageing at field level and investigate its effect on extractable Cd, Cu, Ni, Pb and Zn concentrations from three contaminated soils. The amendments investigated were municipal waste organic compost and biochars. The amendments, soils and mixtures were characterised by their physicochemical properties at different ageing times. The amendments were also characterised in terms of sorption capacity for Cd and Cu. The sorption capacity and the physicochemical properties of the amendments remained constant over the period examined. When mixed with the soils, amendments, especially the compost, immediately reduced the extractable metals in the soils with low pH and acid neutralisation capacity, due to the increase in pH and buffering capacity of the mixtures. The amendments had a relatively minor impact on the metal availability concentrations for the soil with substantially high acid neutralisation capacity. The most important changes in extractable metal concentrations were observed at the beginning of the experiments, ageing having a minor effect on metal concentrations when compared with the initial effect of amendments.

     

污泥含炭吸附剂对挥发性有机废气吸附实验研究

研究了污泥含炭吸附剂对挥发性有机污染物的吸附特性。结果表明,污泥含炭吸附剂对苯系物的吸附为典型的物理吸附,其吸附甲苯等温线的类型系优惠型吸附等温线,表明具有良好的吸附能力;在吸附反应温度为20℃,气体流量为500 mL/m in(停留时间为0.424 s),甲苯浓度为2 700 mg/m3时,甲苯的饱和吸附容量为150.0 mg/g;同时,研究表明污泥含炭吸附剂对苯系物的饱和吸附容量和吸附强弱次序为二甲苯甲苯苯。结果表明污泥含炭吸附剂适合对中低浓度有机废气的吸附净化。     

汽车内微环境空气污染的初步探究

为了研究车内的污染水平,在2004-04-10至2004-06-20对车内空气进行了采样和分析.对车龄在2年内的91种型号轿车的车内微环境进行了静态检测,有效检测车辆共计802辆,同时对比检测20辆2002年以前出厂的旧车.检测项目包括甲醛、苯、甲苯、二甲苯和CO等.参照国家室内空气质量标准,新车中甲苯浓度超标率达82%,苯和甲醛浓度的超标率分别为75%和24%.在被检测车辆中,甲醛、苯、甲苯和二甲苯浓度均是新车比旧车高,只有CO浓度是旧车比新车高.初步分析判断苯系物主要来源于车内的胶粘剂,甲醛来自于车椅座套和座垫等,CO来源于发动机排放残留.     

Characteristic and mechanism of sorption and desorption of benzene on humic acid

Environmental Science and Pollution Research - The sorption/desorption behaviors of benzene, toluene, ethylbenzene, and xylene (BTEX) on soil organic matter (SOM) have a significant influence on...     

Transformation of microflora during degradation of gaseous toluene in a biofilter detected using PCR-DGGE

A laboratory-scale biofiltration system, the rotatory-switching biofilter (RSB), was operated for 199 days using toluene as a model pollutant. The target gaseous pollutant for the biofiltration experiment was approximately 300 ppmv of toluene. Toluene removal efficiency (RE, %) was initially approximately 20% with a 247-ppmv concentration (0.9 g m(-3)) of toluene during the first 10 days. Although the RE decreased several times whenever nitrogen was consumed, it again reached almost 100% when the nitrogen source was in sufficient supply. Denaturing gradient gel electrophoresis (DGGE) analysis was employed to assess the transformation ofmicroflora during operation of the biofilter The results based on a 16S rRNA gene profile showed that the microbial community structure changed with operation time. Although the microflora changed during the initial period (before day 40), transformation of the bacterial component was hardly observed after day 51. Statistical analyses of the DGGE profiles indicated that the bacterial community was almost unaffected by the environmental factors, such as adding ozone, high-level nitrogen supply, increase of loading toluene, and the shutdown of the RSB. The DGGE profile using tmoA-like genes, which encode proteins belonging to the hydroxylase component mono-oxygenases involved in the initial attack of aerobic benzene, toluene, ethylbenzene, and xylene degradation, confirmed the existence of toluene-degrading bacteria. There were at least four kinds of toluene-degradable bacteria having tmoA-like genes up to day 36, which decreased to two species after day 40. Sequence analysis after DGGE profiling revealed that Burkholderia cepacia, Sphingobacterium multivorum, and Pseudomonas putida were present in the biofilter. Only Alicycliphilus denitrificans was present throughout the whole operation period. In the initial stage of operating the RSB, many types of bacteria may have tried to adapt to the conditions, and subsequently, only selected bacteria were able to grow and to degrade toluene.     

Droplet evaporation from porous surfaces; model validation from field and wind tunnel experiments for sand and concrete

The evaporation model of Roberts and Griffiths (1995 Atmospheric Environment 29, 1307–1317) has been subjected to an extensive validation exercise based on a major campaign of field experiments on evaporation from surfaces composed of sand and of concrete. This complements the previous validation which was limited to wind tunnel experiments on sand surfaces. Additionally, the validation using wind tunnel data has been extended to include concrete surfaces. The model describes the constant-rate and falling-rate periods that characterise evaporation from porous media. During the constant-rate period, the evaporation is solely determined by the vapour transport rate into the air. During the falling-rate period, the process in the porous medium is modelled as a receding evaporation front, the overall evaporation rate being determined by the combined effects of vapour transport through the pore network and subsequently into the air. The field trials programme was conducted at sites in the USA and the UK, and examined the evaporation of diethyl malonate droplets from sand and concrete surfaces. Vapour concentrations at several heights in the plume were measured at the centre of a 1 m radius annular source (of width 10 cm) contaminated by uniformly sized droplets (2.4 or 4.1 mm in diameter), key meteorological data being measured at the same time. The evaporation was quantified by coupling concentration and wind speed data. In all, 22 trials were performed on sand and concrete; a further 8 were performed on non-porous surfaces (aluminium foil and slate) as references. The model performance was evaluated against the experimental data in terms of two quantities, the initial evaporation rate of the embedded droplets, and the mass-fraction remaining in the substrate at intervals over the evaporation episode. Overall, the model performance was best in the case of the field experiments for concrete, and the wind tunnel experiments for sand; the performance for wind tunnel experiments for concrete was reasonably good; in the case of the field experiments for sand there was significant underprediction of evaporation rates, though the trends with the determining variables were well predicted.     

Comparison of arsenate and cadmium toxicity in a freshwater amphipod (Gammarus pulex)

Cadmium is largely documented on freshwater organisms while arsenic, especially arsenate, is rarely studied. The kinetic of the LC50s values for both metals was realized on Gammarus pulex. Physiological [i.e. metal concentration in body tissues, bioconcentration factor (BCF)] effects and behavioural responses (via pleopods beats) were investigated after 240-h exposure. Arsenate LC50 value was 100 fold higher than Cd-LC50 value after 240-h exposure, while concentrations in gammarids were similar for both metals at their respective LC50s. BCF decreased with increasing cadmium concentration while BCF remained stable with increasing arsenate concentration. Moreover, BCF was between 148 and 344 times lower for arsenate than cadmium. A significant hypoventilation was observed for cadmium concentrations exceeding or close to the 240h-LC50(Cd), while gammarids hyperventilated for the lowest arsenate concentrations and hypoventilated for the highest arsenate concentrations. We discussed the relationships between potential action mechanisms of these two metals and observed results.     

Nitrate-enhanced bioremediation of BTEX-contaminated groundwater: parameter estimation from natural-gradient tracer experiments

Two natural-gradient pulse tracer tests were conducted in a petroleum-contaminated aquifer to evaluate the potential for benzene, toluene, ethylbenzene, and xylenes (BTEX) biodegradation under enhanced nitrate-reducing conditions. Addition of nitrate resulted in loss of toluene, ethylbenzene, and m,p-xylenes (TEX) after an initial lag period of approximately 9 days. Losses of benzene were not observed over the 60-day monitoring period. Tracer breakthrough curves (BTCs) were analyzed to derive transport and biodegradation parameters, including advective velocities, retardation factors, dispersion coefficients, biodegradation rate constants, and nitrate utilization ratios. Using the parameters derived from the BTC analysis, numerical simulations of one of the tracer experiments were conducted using BIONAPL/3D [Molson, J., BIONAPL/3D User Guide, A 3D Coupled Flow and Multi-Component Reactive transport model. University of Waterloo, Waterloo, Ontario, Canada]. Simulations using the BTC-derived transport and biodegradation parameters successfully reproduced benzene, TEX, and nitrate concentrations measured during the tracer experiment. Comparisons of observed and simulated nitrate concentrations indicate that the mass ratio of nitrate-N utilized to TEX degraded increased over time during the experiment, reaching values many times that expected based on stoichiometry of TEX oxidation coupled to nitrate reduction. Excess nitrate loss is likely due to oxidation of other organics in addition to TEX.