Recycling of municipal solid waste incinerator fly ash by using hydrocyclone separation

The municipal solid waste incinerators (MSWIs) in Taiwan generate about 300,000 tons of fly ash annually, which is mainly composed of calcium and silicon compounds, and has the potential for recycling. However, some heavy metals are present in the MSWI fly ash, and before recycling, they need to be removed or reduced to make the fly ash non-hazardous. Accordingly, the purpose of this study was to use a hydrocyclone for the separation of the components of the MSWI fly ash in order to obtain the recyclable portion. The results show that chloride salts can be removed from the fly ash during the hydrocyclone separation process. The presence of a dense medium (quartz sand in this study) is not only helpful for the removal of the salts, but also for the separation of the fly ash particles. After the dense-medium hydrocyclone separation process, heavy metals including Pb and Zn were concentrated in the fine particles so that the rest of the fly ash contained less heavy metal and became both non-hazardous and recyclable.     

Chemical stability of geopolymers containing municipal solid waste incinerator fly ash

Municipal solid waste incinerators every year produce tons of fly ashes which, differently from coal fly ashes, contain large amounts of toxic substances (heavy metals, dioxins, furans). The stabilization/solidification (S/S) technology known as geopolymerization is proposed with the purpose to bond physically and chemically incinerator fly ashes (IFA) in a solid matrix, in order to reduce pollutant mobility. The chemical stability of geopolymers with Si/Al ratio of 1.8–1.9 and Na/Al ratio of 1.0, synthesized by alkali activation of metakaolin and the addition of 20 wt% of two different kinds of IFA, is presented. The concentration of the alkaline solution, water to solid ratio and curing process have been optimized. The room temperature consolidation of IFA containing geopolymers has been tested for leachability in water for 1 day, accordingly to EN 12457 regulation and extended to 7 days to increase the water attack on solid granules. Leachable metals in the test solution, determined by ICP_AES, fall within limit values set by regulation for non-dangerous waste landfill disposal. Geopolymeric matrix evolution with leaching time has been also evaluated in terms of pH and electrical conductivity increase in solution.     

Corrosion behavior of glass and glass-ceramics made of municipal solid waste incinerator fly ash

Glasses and glass-ceramics were prepared by melting municipal solid waste (MSW) incinerator fly ash and their corrosion properties were evaluated. Corrosion of both materials proceeded in two different steps. At the initial stage, the corrosion process is a diffusion-controlled process. After approximately 10 h at the initial stage, weight losses increased linearly with time due to the total dissolution of glasses or glass-ceramics. Leaching of heavy metals from glasses and glass-ceramics were well within international environmental regulations. Corrosion proceeded uniformly in fly ash glass while Na2CaSiO4 crystalline phase was preferentially dissolved in the glass-ceramics.     

Heavy metal speciation in various types of fly ash from municipal solid waste incinerator

Fly ash (FA) from municipal solid waste incinerators has been known as hazardous waste, which is mostly because of the high content of heavy metal and dioxins. Besides the content, the form of the heavy metals in fly ash is also very important, because it is tightly related with the leaching behavior of fly ash in diverse circumstances. To evaluate the environment potential risk of fly ash, the Tessier chemical extraction method was adopted. In this study, four kinds of fly ash were examined, one sample from China (CFA) and the other three from Japan (RFA, CaFA and NaFA). Five metal elements were detected and they were Ni, Cr, Cd, Pb, and Cu. The result of total heavy metals’ concentration showed CFA has the lowest content. As to the Tessier chemical extraction experiments, the results show that Cd, Pb, and Cu have higher leaching risk in the environment than other heavy metals. The result of leaching test experiment showed that the more exchangeable speciation of Cd, Cr and Pb in FA, the more it could leach out in natural environment.     

Leaching behavior of polychlorinated dibenzo-p-dioxins and furans from the fly ash and bottom ash of a municipal solid waste incinerator

The leaching behavior of dioxins from landfill containing bottom ash and fly ash from municipal solid waste incineration has been investigated by leaching tests with pure water, non-ionic surfactant solutions, ethanol solutions, or acetic acid solutions as elution solvents for a large-scale cylindrical column packed with ash. Larger amounts of dioxins were eluted from both bottom ash and fly ash with ethanol solution and acetic acid solution than with pure water. Large quantities of dioxins were leached from fly ash but not bottom ash by non-ionic surfactant solutions. The patterns of distribution of the dioxin congeners in the leachates were very similar to those in the bottom ash or fly ash from which they were derived.     

Phosphorus recovery from municipal solid waste incineration fly ash

The potential of phosphorus (P) recycling from municipal solid waste incineration (MSWI) residue is investigated. Vast and ever increasing amounts of incineration residues are produced worldwide; these are an environmental burden, but also a resource, as they are a major sink for the material flows of society. Due to strict environmental regulations, in combination with decreasing landfilling space, the disposal of the MSWI residues is problematic. At the same time, resource scarcity is recognized as a global challenge for the modern world, and even more so for future generations.This paper reports on the methods and efficiency of P extraction from MSWI fly ash by acid and base leaching and precipitation procedures. Phosphorus extracted from the MSWI residues generated each year could meet 30% of the annual demand for mineral phosphorus fertiliser in Sweden, given a recovery rate of 70% achieved in this initial test.The phosphorus content of the obtained product is slightly higher than in sewage sludge, but due to the trace metal content it is not acceptable for application to agricultural land in Sweden, whereas application in the rest of the EU would be possible. However, it would be preferable to use the product as a raw material to replace rock phosphate in fertilizer production. Further development is currently underway in relation to procedure optimization, purification of the phosphorus product, and the simultaneous recovery of other resources.     

Synthesis of mesoporous silica materials from municipal solid waste incinerator bottom ash

Incinerator bottom ash contains a large amount of silica and can hence be used as a silica source for the synthesis of mesoporous silica materials. In this study, the conditions for alkaline fusion to extract silica from incinerator bottom ash were investigated, and the resulting supernatant solution was used as the silica source for synthesizing mesoporous silica materials. The physical and chemical characteristics of the mesoporous silica materials were analyzed using BET, XRD, FTIR, SEM, and solid-state NMR. The results indicated that the BET surface area and pore size distribution of the synthesized silica materials were 992 m²/g and 2–3.8 nm, respectively. The XRD patterns showed that the synthesized materials exhibited a hexagonal pore structure with a smaller order. The NMR spectra of the synthesized materials exhibited three peaks, corresponding to Q² [Si(OSi)₂(OH)₂], Q³ [Si(OSi)₃(OH)], and Q⁴ [Si(OSi)₄]. The FTIR spectra confirmed the existence of a surface hydroxyl group and the occurrence of symmetric Si–O stretching. Thus, mesoporous silica was successfully synthesized from incinerator bottom ash. Finally, the effectiveness of the synthesized silica in removing heavy metals (Pb²⁺, Cu²⁺, Cd²⁺, and Cr²⁺) from aqueous solutions was also determined. The results showed that the silica materials synthesized from incinerator bottom ash have potential for use as an adsorbent for the removal of heavy metals from aqueous solutions.     

Comparison of two types of municipal solid waste incinerator fly ashes with different alkaline reagents in washing experiments

In this study, we propose a "washing-calcination-conversion of washed fly ash into cement material with bottom ash" (WCCB) system to reduce the amount of fly ash that must be specially treated so it can be used as raw cement material. Calcium hydroxide (Ca(OH)2) is widely used in air-pollution control devices of incinerators while sodium bicarbonate (NaHCO3) is not. We conducted single-, double-, and triple-washing experiments to compare the washing characteristics of two types of fly ash. Unlike NaHCO3 fly ash, Ca(OH)2 fly ash has almost twice as much washed residue and almost 2.5 times more chlorine after the same washing procedure. After washing once, the washing frequency is also important for NaHCO3 fly ash, while the mixing time and liquid/solid ratio are more critical for Ca(OH)2 fly ash. The use of NaHCO3 is more suitable for the WCCB system.     

Investigation of hydrogen generation from municipal solid waste incineration fly ash

Hydrogen generation from municipal solid waste incineration fly ash was investigated to understand the influences of contacting method, kinds of contact solution, liquid to solid ratio, and particle size distribution of materials. Redox properties of materials and hydrogen generation were also studied. The largest quantity of gas generated in contact with water was 29.1 ml/g-ash, most of which was hydrogen. Fluidized bed fly ash generated more gas than stoker fly ash. In order to calculate the hydrogen generation potential (the maximum quantity of gas generated in contact with water), a novel system using a Y-shaped test tube and NaOH was utilized. This method gives values which are related to the quantity of generated gas in contact with water. A relationship between the aluminum content and hydrogen generation potential was observed, especially for fluidized bed fly ash. The reducing potential of fluidized bed fly ash was higher than that of stoker fly ash. Only fluidized bed fly ash showed a positive correlation between aluminum content and reducing potential, and between reducing potential and hydrogen generation potential. These results suggest that fluidized bed fly ash contains more Al⁰ than stoker fly ash. Received: September 11, 1998 / Accepted: March 19, 1999     

Effect of the milling solution on lead stabilization in municipal solid waste incinerator fly ash during the milling processes

The wet milling process had been found to effectively stabilize lead in fly ash. This study adopts this method and looks at the effect of different milling solutions to improve the efficiency of lead stabilization. Different milling solutions (water, phosphoric acid and ethanol) and different milling times (1, 24, 48 and 96 h) were selected as parameters. Since lead oxide can be identified by XRD in this experiment’s samples, 5% lead oxide was added to the extracted mixed fly ash to make instrumental analysis easier. The experimental results indicate that the effect of stabilization of lead after milling could exceed 96%. During milling with water, considerable lead leached into the water in the initial stage (1 h) of the process, but a stable level was reached as the milling time increased. After milling with ethanol and 0.2 M phosphoric acids, the efficiency could exceed 93% after 1 h of milling time. The results of the sequential extraction procedure (SEP) results show that the residual fraction could be increased from 8.93% to 56.16% when a 0.2 M phosphoric acid solution was used. Clearly the choice of an appropriate milling solution can enhance lead stabilization in the fly ash.     

Hydrothermal solidification of municipal solid waste incineration bottom ash with slag addition

Hydrothermal solidification of municipal solid waste incineration (MSWI) bottom ash has been carried out under saturated steam pressure (1.56 MPa) at 200 °C for up to 24 h by mixing quartz, slaked lime and water-cooled blast furnace slag (WBFS). The strength enhancement for the WBFS addition was best. The strength development was shown to be due mainly to tobermorite formation, and the tobermorite formation densified matrix, thus promoting the strength development. WBFS seemed to have a higher reactivity than the quartz during the initial hydrothermal process, which provided more silica available to harden the solidified specimens. However, a longer curing time (24 h) was favorable to the quartz dissolution for tobermorite formation, which in turn, enhanced the strength for quartz addition. Curing time affected the crystal morphology evolution, and the stubby plate of tobermorite seemed to result in a high strength enhancement in this study. Laboratory leaching tests were conducted to determine the amount of heavy metals dissolved from the final solidified specimens, and the leaching results showed that after hydrothermal processing the heavy metals dissolved from the solidified specimens were reduced effectively. As such, the hydrothermal processing may have a high potential for recycling/reusing MSWI ash on a large scale.     

Physical-mechanical and environmental properties of sintered municipal incinerator fly ash

A step-wise treatment of Municipal Solid Waste (MSW) incinerator fly ash including washing, milling and sintering was investigated in order to manufacture ceramic materials with improved physical, mechanical and environmental properties and, possibly, to reduce the power input of the sintering process. An interpretation of the test results based on the microstructure of sintered products and sintering kinetic modeling was also attempted to identify the densification mechanisms. It was found that milling of washed fly ash represents a basic step for manufacturing high-density ceramic materials with very high compressive strengths (up to 500 N/mm2). A significant reduction in the power input of the sintering process (reduction of firing temperature from 1210 degrees C for washed fly ash to 1140 degrees C for milled-washed fly ash) is also achieved. A dense, well-sintered microstructure is formed through an intermediate-stage, liquid-phase sintering mechanism controlled by liquid-phase diffusion and grain shape accommodation. Such a microstructure is able to strongly immobilise heavy metals, thus giving good environmental properties to sintered product.     

Hydrothermal solidification behavior of municipal solid waste incineration bottom ash without any additives

Municipal solid waste incineration (MSWI) bottom ash could be solidified with and without slaked lime (calcium hydroxide) addition by a hydrothermal method under steam pressure of 1.56 MPa at 200 °C for up to 72 h. Experimental results showed that CSH gel or tobermorite exerted a main influence on strength development, and without any additives CSH gel was easy to form, while slaked lime addition favored to form tobermorite. Tobermorite seemed to exert a larger effect on the strength development than CSH gel. Leaching results showed that the concentrations of heavy metals dissolved from the solidified specimens were effectively reduced after hydrothermal processing. The immobilization was mainly due to the tobermorite or CSH gel formation, and Pb²⁺ and Zn²⁺ seemed to be fixed more readily than Cr⁶⁺, which might be the reason that the structural Ca²⁺ within tobermorite or CSH gel was exchanged by Pb²⁺ and Zn²⁺ more easily than Cr⁶⁺. In addition, there existed a close relationship between leaching concentration and strength enhancement, and a higher strength seemed to exert a larger effect on immobilization of heavy metals.     

Removal of carbon constituents from hospital solid waste incinerator fly ash by column flotation

Hospital solid waste incinerator (HSWI) fly ash contains a large number of carbon constituents including powder activated carbon and unburned carbon, which are the major source of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in fly ash. Therefore, the removal of carbon constituents could reduce PCDD/Fs in fly ash greatly. In this study, the effects of the main flotation parameters on the removal of carbon constituents were investigated, and the characteristics of the final product were evaluated. The results showed that loss on ignition (LOI) of fly ash increased from 11.1% to 31.6% during conditioning process. By optimizing the flotation parameters at slurry concentration 0.05 kg/l, kerosene dosage 12 kg/t, frother dosage 3 kg/t and air flow rate 0.06 m³/h, 92.7% of the carbon constituents were removed from the raw fly ash. Under these conditions, the froth product has LOI of 56.35% and calorific values of 12.5 MJ/kg, LOI in the tailings was below 5%, and the total toxic equivalent (TEQ) of PCDD/Fs decreased from 5.61 ng-TEQ/g in the raw fly ash to 1.47 ng-TEQ/g in the tailings. The results show that column flotation is a potential technology for simultaneous separation of carbon constituents and PCDD/Fs from HSWI fly ash.     

Utilization of municipal solid waste incineration fly ash for sulfoaluminate cement clinker production

The feasibility of partially substituting raw materials with municipal solid waste incineration (MSWI) fly ash in sulfoaluminate cement (SAC) clinker production was investigated by X-ray diffraction (XRD), compressive strength and free expansion ratio testing. Three different leaching tests were used to assess the environmental impact of the produced material. Experimental results show that the replacement of MSWI fly ash could be taken up to 30% in the raw mixes. The good quality SAC clinkers are obtained by controlling the compositional parameters at alkalinity modulus (C(m)) around 1.05, alumina-sulfur ratio (P) around 2.5, alumina-silica ratio (N) around 2.0~3.0 and firing the raw mixes at 1250 °C for 2h. The compressive strengths of SAC are high in early age while that develop slowly in later age. Results also show that the expansive properties of SAC are strongly depended on the gypsum content. Leaching studies of toxic elements in the hydrated SAC-based system reveal that all the investigated elements are well bounded in the clinker minerals or immobilized by the hydration products. Although some limited positive results indicate that the SAC prepared from MSWI fly ash would present no immediate thread to the environment, the long-term toxicity leaching behavior needs to be further studied.     

国内城市生活垃圾焚烧飞灰研究现状及进展

随着我国经济快速发展及城市化水平提升,城市生活垃圾产量越来越大,焚烧逐渐成为城市生活垃圾处理的主要方式.但焚烧会产生大量的垃圾焚烧飞灰(以下简称飞灰),飞灰属于危险废物.论述了飞灰的来源、成分、特性及危害,介绍了飞灰的处理处置技术:水泥固化技术、化学药剂稳定化技术、熔融固化技术、水热稳定化技术和水泥窑协同处理技术,并分...     

Sequestration of metals in carbonated municipal solid waste incineration (MSWI) fly ash

Waste management is in need of a reliable and economical treatment method for metals in fly ashes from municipal solid waste incineration (MSWI). However, no state-of-the-art technique has gained wide acceptance yet. This paper is a synthesis of five elsewhere published investigations covering a project which aimed to assess the possibilities and limitations of adding carbon dioxide (CO2) to fly ash as a stabilization method. Carbonation factors that were studied are the partial pressure of carbon dioxide (CO2), the addition of water, the temperature, and the reaction time. Laboratory experiments were performed applying methods such as factorial experimental design, thermal analysis, scanning electron microscopy (SEM), X-ray diffraction (XRD), and leaching assays including pHstat titration and sequential extraction. Leaching data were verified and complemented using chemical equilibrium calculations. Data evaluation was performed by means of multivariate statistics such as multiple linear regression, principal component analysis (PCA), and partial least squares (PLS) modeling. It was found that carbonation is a good prospect for a stabilization technique especially with respect to the major pollutants lead (Pb) and zinc (Zn). Their mobility decreased with increasing factor levels. Dominating factors were the partial pressure of CO2 and the reaction time, while temperature and the addition of water were of minor influence. However, the treatment caused a mobilization of cadmium (Cd), requiring further research on possible countermeasures such as metal demobilization through enhanced silicate formation.     

Production of cement clinkers from municipal solid waste incineration (MSWI) fly ash

This communication reports the laboratory scale study on the production of cement clinkers from two types of municipal solid waste incineration fly ash (MSW ash) samples. XRD technique was used to monitor the phase formation during the burning of the raw mixes. The amount of trace elements volatilized during clinkerization and hydration, as well as leaching behaviours of the clinkers obtained from optimum compositions, were also evaluated. From the results it is observed that all of the major components of ordinary Portland cement (OPC) clinkers are present in the produced clinkers. Results also show the volatilization of considerable amounts of Na, K, Pb, Zn and Cd during the production of clinkers. However, major parts of the toxic elements remaining in the clinkers appear to be immobilized in the clinkers phases. Hydration studies of the clinkers obtained from optimum compositions show that the clinkers prepared from raw MSW ash are more reactive than the washed MSW ash based clinkers. TG/DTA analyses of the hydrated pastes show the formation of hydration products, which are generally found in OPC and OPC derived cements. The initial study, therefore, shows that more than 44% of MSW ash with the addition of very small amounts of silica and iron oxide can be used to produce cement clinkers. The amount of CaCO3 necessary to produce clinkers (approximately 50%) is also smaller than the same required for the conventional process (more than 70%).     

Integrated municipal solid waste treatment using a grate furnace incinerator: the Indaver case

An integrated installation for treatment of municipal solid waste and comparable waste from industrial origin is described. It consists of three grate furnace lines with flue gas treatment by half-wet scrubbing followed by wet scrubbing, and an installation for wet treatment of bottom ash. It is demonstrated that this integrated installation combines high recovery of energy (40.8% net) with high materials recovery. The following fractions were obtained after wet treatment of the bottom ash: ferrous metals, non-ferrous metals, three granulate fractions with different particle sizes, and sludge. The ferrous and non-ferrous metal fractions can both be recycled as high quality raw materials; the two larger particle size particle fractions can be applied as secondary raw materials in building applications; the sand fraction can be used for applications on a landfill; and the sludge is landfilled. For all components of interest, emissions to air are below the limit values. The integrated grate furnace installation is characterised by zero wastewater discharge and high occupational safety. Moreover, with the considered installation, major pollutants, such as PCDD/PCDF, Hg and iodine-136 are to a large extent removed from the environment and concentrated in a small residual waste stream (flue gas cleaning residue), which can be landfilled after stabilisation.