Effects of γ-Fe2O3 nanoparticles on the survival and reproduction of Biomphalaria glabrata (Say, 1818) and their elimination from this benthic aquatic snail

Environmental Science and Pollution Research - This study aims to evaluate the effects of maghemite nanoparticles (γ-Fe2O3) coated with meso-2, 3-dimercaptosuccinic acid (DMSA) stabilizer on...     

Facile synthesis of nanosheet-assembled γ-Fe2O3 magnetic microspheres and enhanced Sb(III) removal

Environmental Science and Pollution Research - The development and utilization of magnetic nanoadsorption materials with large adsorption capacity and easy separation are the research hotspot...     

Study on low-temperature plasma γ-Al2O3 catalytic viscosity reduction of polyacrylamide solution

The wide use of polyacrylamide (PAM) in enhanced oil recovery generates a large amount of polymer-bearing wastewater featuring high viscosity and difficult viscosity reduction, making the treatment of wastewater increasingly difficult. In this paper, the experimental study on reducing the viscosity of wastewater containing polyacrylamide by using the plasma generated by dielectric barrier discharge (DBD) and the synergistic effect of catalyst γ-Al₂O₃ is carried out. The law of plasma reducing the viscosity of wastewater containing polyacrylamide is studied under the different conditions of amounts of γ-Al₂O₃ catalyst, discharge voltages, and initial concentrations of polyacrylamide-containing wastewater. The mechanism of viscosity reduction of polyacrylamide is studied through environmental scanning electron microscope (ESEM), Fourier transform infrared (FTIR) spectrometer, and X-ray photoelectron spectroscopy (XPS). The results show that the catalytic viscosity reduction is the best when the discharge voltage is 18 kV and the discharge time is 15 min. With the increase in the input of the γ-Al₂O₃ catalyst, the viscosity of the PAM solution decreases gradually. When the amount of γ-Al₂O₃ is 375 mg, the shear rate changes from 0.5 1/sec to 28 1/sec, and the viscosity of the solution containing polyacrylamide changes from 434.5 mPa·s to 40.2 mPa·s. The viscosity reduction rate of the PAM solution is 90.7%. After the catalytic viscosity reduction, the functional groups of polyacrylamide do not change much. The elemental composition of the catalyst has not changed, which is still Al, C, and O.

     

Capture of CO2 on γ-Al2O3 materials prepared by solution-combustion and ball-milling processes

A series of porous γ-Al₂O₃ materials was prepared by solution-combustion and ball-milling processes. The as-prepared powders were physicochemically characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), and N₂ physisorption measurements and their performances in CO₂ adsorption at different pressures (0.5 to 1.5 MPa) and temperatures (40 to 60ºC) were investigated. It was found that γ-Al₂O₃ synthesized by the solution-combustion process and ball milled at 10 hr exhibited the best CO₂ adsorption performance at 60ºC and 1.5 MPa, achieving a maximum of 1.94 mmol/g compared to the four studied materials, as a result of their interesting microstructure and surface properties (i.e., nanocrystallinity, specific surface area, narrow pore size distribution, and large total pore volume). Our study shows that the γ-Al₂O₃ prepared by solution combustion followed by ball milling presents a fairly good potential adsorbent for efficient CO₂ capture.

Implications: In this work, γ-Al₂O₃ materials were successfully obtained by solution combustion and modified via ball milling. These improved materials were systematically investigated as solid adsorbents of accessible surface areas, large pore volumes, and narrow pore size distribution for the CO₂ capture. These studied solid adsorbents can provide an additional contribution and effort to develop an efficient CO₂ capture method as means of alleviating the serious global warning problem.     

Synthesis of γ-Fe2O3/La/Bi2WO6 composites for enhanced visible light-driven photocatalytic degradation of tetracycline hydrochloride

Environmental Science and Pollution Research - γ-Fe2O3/La/Bi2WO6 heterojunction composites have been successfully synthesized by simple and convenient hydrothermal method. The photocatalytic...     

Evidence of the water-cage effect on the photolysis of NO3− and FeOH2+. Implications of this effect and of H2O2 surface accumulation on photochemistry at the air–water interface of atmospheric droplets

Experiments are conducted to determine the effect of a cage of water molecules on the photolysis quantum yields of nitrate, FeOH²⁺, and H₂O₂. Results suggest that the quantum yields of nitrate and FeOH²⁺ are decreased by the recombination of photo-fragments ( OH +  NO₂ and Fe²⁺ +  OH, respectively) before they leave the surrounding cage of water molecules. However, no evidence is found for an enhanced quantum yield for H₂O₂. Therefore, the photolysis of nitrate and FeOH²⁺ could be enhanced if the cage of the solvent molecules is incomplete, as is the case at the air–water interface of atmospheric droplets. The photolysis rate constant distribution within nitrate, FeOH²⁺, and H₂O₂ aerosols is calculated by combining the expected quantum yield data in the bulk and at the interface with Mie theory calculations of light intensity. The photolysis rate constant of nitrate and FeOH²⁺ would be significantly higher at the surface than in the bulk if quantum yields are enhanced at the surface. In the case of H₂O₂, the photolysis rate constant would be enhanced by surface accumulation. The results concerning the expected rates of photolysis of these photoactive species are applied to the assessment of the reaction between benzene and OH in the presence of OH scavengers in an atmospherically relevant scenario. For a droplet of 1 μm radius, a large fraction of the total OH-benzene reaction (15% for H₂O₂, 20% for nitrate, and 35% for FeOH²⁺) would occur in the surface layer, which accounts for just 0.15% of the droplet volume.     

The effect of air pollution on drivers’ safety performance

Environmental Science and Pollution Research - Numerous studies have determined the adverse effects of air pollution on the health, welfare, and comfort of humans. More recently, the effects of air...     

Al2O3 nanoparticles trigger the embryonic hepatotoxic response and potentiate TNF-α-induced apoptosis—modulatory effect of p38 MAPK and JNK inhibitors

Environmental Science and Pollution Research - Recent evidences illustrated that the release of aluminum oxide nanoparticles (Al2O3-NPs) into the biosphere may pose risk to the environment and...     

The climatology of summertime O3 and SO2 (1977–1981)

The mean monthly distribution of the diurnal maximum O₃ and of the SO₂ in the eastern two-thirds of the U.S. was determined for the summer (July and August) of 1977–1981. Highest O₃ concentrations varied from 60 to 90 ppbv and covered an area of about 2 to 5 × 10⁶ km²; and that for SO₂ varied from values greater than 10 ppbv to values about 25 ppbv and covered an area of 0.3–1.3 × 10⁶ km². The geographical locations of the centers of high O₃ concentrations were related to the path of the anticyclones. The centers of high SO₂ concentration were affected by the path of anticyclones but to a lesser extent. The SO₂ distribution was controlled to a significant extent by the location of major SO₂ sources. The data suggested that highpressure systems that become stationary, weaken and dissipate in the eastern two-thirds of the U.S. have a profound effect on the O₃ and SO₂ distribution.     

Synthesis of α-Fe2O3 nanofibers for applications in removal and recovery of Cr(VI) from wastewater

Purpose

Nanomaterials such as iron oxides and ferrites have been intensively investigated for water treatment and environmental remediation applications. The purpose of this work is to synthesize α-Fe₂O₃ nanofibers for potential applications in removal and recovery of noxious Cr(VI) from wastewater.

Methods

α-Fe₂O₃ nanofibers were synthesized via a simple hydrothermal route followed by calcination. The crystallographic structure and the morphology of the as-prepared α-Fe₂O₃ nanofibers were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope. Batch adsorption experiments were conducted, and Fourier transform infrared spectra were recorded before and after adsorption to investigate the Cr(VI) removal performance and adsorption mechanism. Langmuir and Freundlich modes were employed to analyze the adsorption behavior of Cr(VI) on the α-Fe₂O₃ nanofibers.

Results

Very thin and porous α-Fe₂O₃ nanofibers have been successfully synthesized for investigation of Cr(VI) removal capability from synthetic wastewater. Batch experiments revealed that the as-prepared α-Fe₂O₃ nanofibers exhibited excellent Cr(VI) removal performance with a maximum adsorption capacity of 16.17 mg g^?1. Furthermore, the adsorption capacity almost kept unchanged after recycling and reusing. The Cr(VI) adsorption process was found to follow the pseudo-second-order kinetics model, and the corresponding thermodynamic parameters ΔG°, ΔH°, and ΔS° at 298 K were calculated to be ?26.60 kJ?mol^?1, ?3.32 kJ?mol^?1, and 78.12 J?mol^?1 K^?1, respectively.

Conclusions

The as-prepared α-Fe₂O₃ nanofibers can be utilized as efficient low-cost nano-absorbents for removal and recovery of Cr(VI) from wastewater.     

Synthesis and characterization of γ-ferric oxide nanoparticles and their effect on <Emphasis Type="Italic">Solanum lycopersicum</Emphasis>

γ-Ferric oxide nanoparticles are synthesized through modern and facile ayurvedic route followed by normal and special purification steps, which are both cost-effective and eco-friendly. These synthesized γ-ferric oxide nanoparticles were applied on Solanum lycopersicum to search the effect on chlorophyll content. This process involves multiple filtration and calcination steps. The synthesized samples were analyzed by X-ray diffraction (XRD), UV-visible (UV-vis) spectroscopy, transmission electron microscopy (TEM), vibrating sample magnetometry (VSM), and particle size analysis (PSA) to identify the purification step’s influence on the structural, optical, morphological, magnetic, and particle size properties of ferric oxide nanoparticles (γ-phase). X-ray diffraction has revealed that ferric oxide nanoparticles have rhombohedral structure of α-phase (hematite) in initial purification process later transformed into cubic structure γ-phase (maghemite). UV-vis spectroscopy analysis has clearly shown that by repetitive purification steps, λ_max has increased from 230 to 340 nm. TEM result has an intercorrelation with XRD results. γ-Ferric oxide nanoparticles were tested on Solanum lycopersicum (tomato seeds). The changes in the contents of chlorophyll a, chlorophyll b, and total carotene were studied using spectral measurements at two different dosages—0.5 and 2 M. As a result, at 0.5-M concentration, magnetic nanoparticles exhibit fruitful results by increasing the crop yield and being more resistant to chlorosis.     

TiO2/SiO2/γ-Fe2O3的表征及其光催化降解染料废水

以γ-Fe2O3为磁性核心,通过溶胶-凝胶法制备出三层结构的复合光催化剂TiO2/SiO2/γ-Fe2O3.通过X射线衍射、扫描电镜、透射电镜、振动样品磁强计和紫外-可见分光光谱分析进行表征.SiO2包覆膜可以减弱内层γ-Fe2O3对光催化效果的不利影响,有效地阻隔高温时γ-Fe2O3磁核与TiO2之间的熔结.以亚甲基...     

The effect of air pollution and emotional and behavioral problems on preschoolers’ overweight and obesity

Environmental Science and Pollution Research - Childhood overweight and obesity (OWO) has risen dramatically in both developed and developing countries over the past few decades, creating a huge...     

O3、H2O2／O3及UV／O3在焦化废水深度处理中的应用

采用O3、H2O2／O3及UV／O3等高级氧化技术（AOPs）对某焦化公司的生化出水进行深度处理,考察了O3与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响,确定出O3氧化反应的最佳工艺参数为：接触时间40min,溶液pH8．5,反应温度25℃,此条件下废水COD及UV254的去除率最高可达47．14％和73．47％;H2O2／O3及UV／O3两种组合工艺对焦化废水COD及UV254的去除率均有一定程度的提高,但H2O2／O3系统的运行效果取决于H2O2的投加量。研究结论表明,单纯采用COD作为评价指标,并不能准确反映出O3系列AOPs对焦化废水中有机污染物的降解作用。     

Fe-Mn/γ-Al2O3催化O3-H2O2协同氧化间甲酚

为提高臭氧氧化法对难降解有机污染物的降解效率,采用在催化臭氧氧化体系中引入H_2O_2的方法,建立催化O_3-H_2O_2联合氧化体系,使O_3与H_2O_2在体系中起协同作用。采用等体积浸渍法筛选制备了具有高催化性能的Fe-Mn/γ-Al_2O_3催化剂,应用于O_3/Fe-Mn/γ-Al_2O_3/H_2O_2复合体系协同催化臭氧氧化处理间甲酚模型废水。通过扫描电子显微镜(SEM)、物理吸附、X射线衍射(XRD)、X射线荧光光谱(XRF)、X射线光电子波谱(XPS)对催化剂的物理化学性质进行表征。考察了O_3投加量、H_2O_2投加量、初始pH、空速等因素对Fe-Mn/γ-Al_2O_3催化O_3-H_2O_2氧化间甲酚处理效果的影响,并采用GC-MS和LC-OCD,对Fe-Mn/γ-Al_2O_3催化O_3-H_2O_2氧化间甲酚的中间产物的类型及相对分子质量进行分析。结果表明,当以Fe-Mn/γ-Al_2O_3为催化剂时,协同催化氧化体系的最优处理参数为:间甲酚浓度100 mg·L~(-1),O_3投加量481 mg·L~(-1),反应时间10 min,空速6 h~(-1),H_2O_2投加量211 mg·L~(-1),进水pH 6.7。在此条件下,TOC去除率可达68.37%,间甲酚转化率可达100%。以上研究结果可为2种技术联用降解煤化工废水提供参考。     

The effect of nutrients shortage on plant’s efficiency to capture solar radiations under semi-arid environments

Radiation use efficiency (RUE) is considered critical for calculation of crop yield. The crop productivity can be improved by increasing the interception of solar radiation and maintaining higher RUE for plants. Irrigation water and nitrogen (N) supply are the main limiting factors for RUE in maize (Zea mays L.) across the semi-arid environments. Field experiments were conducted during two consecutive growing seasons (2009–2010) to optimize RUE in relation to N application timings and rates with varying irrigation water management practices. In experiment 1, three N application timings were made, while in experiment 2, three possible water management practices were used. In both experiments, five N rates (100, 150, 200, 250, and 300 kg N ha⁻¹) were applied to evaluate the effects of irrigation water and N on cumulative photosynthetic active radiation (PARi), dry matter RUE (RUE_DM), and grain yield RUE (RUE_GY). The results demonstrated that cumulative PARi and RUEs were not constant during the plant growth under varying the nutrients. The water and N significantly influenced cumulative PARi and RUEs during the both growing seasons. In experiment 1, the maximum cumulative PARi was observed by application of 250 kg N ha⁻¹ in three splits (1/3 N at V2, 1/3 N at V16, and 1/3 N at R1 stage), and the highest RUE_DM was achieved by the application of 300 kg N ha⁻¹. However, the highest RUE_GY was observed by application of 250 kg N ha⁻¹. In experiment 2, the maximum cumulative PARi was attained at normal irrigation regime with 250 kg N ha⁻¹, while the highest RUE_DM and RUE_GY were recorded at normal irrigation regime with the application of 300 kg N ha⁻¹. The regression analysis showed significant and positive correlation of RUE_GY with grain yield. Therefore, optimum water and N doses are important for attaining higher RUE, which may enhance maize grain yield semi-arid environment; this may be considered in formulating good agricultural practices for the environmental conditions resembling to those of this study.

     

The effect of polystyrene plastics on the toxicity of triphenyltin to the marine diatom Skeletonema costatum—influence of plastic particle size

Environmental Science and Pollution Research - The effect of polystyrene (PS) particles on the toxicity of triphenyltin (TPT) to the marine diatom Skeletonema costatum was investigated. The...     

Emission of N2O on pulse–rice crop rotation in upland

The Seasonally Integrated Flux (SIF) of N₂O emission during pulse cultivation in Rabi season (Season-I: December to April) in rain-fed uplands of Orissa, was found to be 17.7 ± 0.07, 18.7 ± 0.16 and 43.3 ± 0.14 gha^?1 for horse gram (HG), black gram (BG) and green gram (GG) respectively. During the subsequent Rabi season (Season-II), the SIF of N₂O for BG and GG cultivated in the same fields were 20.9 ± 0.24 and 38.0 ± 0.42 gha^?1 respectively. Similarly SIF values during rice cultivation with different cultivars have also been calculated to be in the range ?20.05 ± 0.33 to 21.98 ± 0.29. Statistical analysis showed good correlation of N₂O emission with climatic and soil parameters like temperature, nutrient N and organic matter in soil during pulse cultivation. Multivariate analysis was carried out to factorize the results obtained. Using student ‘t’ test, the N₂O emission was observed to be similar for two consecutive Rabi seasons for pulses like BG and GG.