Effectiveness of Multi‐Site Weather Generator for Hydrological Modeling1

Khalili, Malika, François Brissette, and Robert Leconte, 2011. Effectiveness of Multi‐site Weather Generator for Hydrological Modeling. Journal of the American Water Resources Association (JAWRA) 1‐12. DOI: 10.1111/j.1752‐1688.2010.00514.x Abstract: A multi‐site weather generator has been developed using the concept of spatial autocorrelation. The multi‐site generation approach reproduces the spatial autocorrelations observed between a set of weather stations as well as the correlations between each pair of stations. Its performance has been assessed in two previous studies using both precipitation and temperature data. The main objective of this paper is to assess the efficiency of this multi‐site weather generator compared to a uni‐site generator with respect to hydrological modeling. A hydrological model, known as Hydrotel, was applied over the Chute du Diable watershed, located in the Canadian province of Quebec. The distributed nature of Hydrotel accounts for the spatial variations throughout the watershed, and thus allows a more in‐depth assessment of the effect of spatially dependent meteorological input on runoff generation. Simulated streamflows using both the multi‐site and uni‐site generated weather data were statistically compared to flows modeled using observed data. Overall, the hydrological modeling using the multi‐site weather generator significantly outperformed that using the uni‐site generator. This latter combined to Hydrotel resulted in a significant underestimation of extreme streamflows in all seasons.     

Managing the cooling capacity of the upper rhine: A case study

In most industrialized countries, environmental standards exist which prescribe the maximum allowable man-made increase in water temperature of a river. Together with flowrate and weather conditions, these standards determine the rate at which waste heat may be discharged into a river at any moment. Power generating stations with variable cooling systems can adjust their heat discharge into the river in compliance with environmental standards and by doing so exert an influence on power generation capacity. In this paper, a scheme is developed that allows a chain of power stations discharging into the same river to operate their cooling systems such that the output of total electricity is maximized and water temperature standards are accomodated. The optimum balance between stations is determined through dynamic programming. From the results of a simulation model using historical data, simple decision rules for day-to-day operation are abstracted. These rules are based solely on the river flow rates at each power station.     

Development of the Spatial Rainfall Generator (SRGEN) for the Agricultural Policy/Environmental Extender Model

Accurate spatial representation of climatic patterns is often a challenge in modeling biophysical processes at the watershed scale, especially where the representation of a spatial gradient in rainfall is not sufficiently captured by the number of weather stations. The spatial rainfall generator (SRGEN) is developed as an extension of the “weather generator” (WXGEN), a component of the Agricultural Policy/Environmental eXtender (APEX) model. SRGEN generates spatially distributed daily rainfall using monthly weather statistics available at multiple locations in a watershed. The spatial rainfall generator as incorporated in APEX is tested on the Cowhouse watershed (1,178 km²) in central Texas. The watershed presented a significant spatial rainfall gradient of 2.9 mm/km in the lateral (north‐south) directions based on four rainfall gages. A comparative analysis between SRGEN and WXGEN indicates that SRGEN performs well (PBIAS = 2.40%). Good results were obtained from APEX for streamflow (NSE = 0.99, PBIAS = 8.34%) and NO₃‐N and soluble P loads (PBIAS ≈ 6.00% for each, respectively). However, APEX underpredicted sediment yield and organic N and P loads (PBIAS: 24.75‐27.90%) with SRGEN, although its uncertainty in output was lower than WXGEN results (PBIAS: ?13.02 to ?46.13%). The overall improvement achieved in rainfall generation by SRGEN is demonstrated to be effective in the improving model performance on flow and water quality output.     

Addressing data challenges in riverine nutrient load modeling of an intensively managed agro-industrial watershed

Data limitations often challenge the reliability of water quality models, especially in intensively managed watersheds. While numerous studies report successful hydrological model setup and calibration, few have addressed in detail the data challenges for multisite and multivariable model calibration to an intensively managed watershed. In this study, we address some of these challenges based on our reflective experience calibrating the Soil and Water Assessment Tool (SWAT) to the Upper Sangamon River Watershed in central Illinois based on daily flow, annual crop yield, and monthly sediment, nitrate, and total phosphorus loads. We highlight some challenges in SWAT calibration processes due to data errors and inconsistencies, and insufficient precipitation and water quality observations. Following, we demonstrate the merits of additional weather and water quality observations that could help reduce input uncertainties, and we provide suggestions for selecting appropriate observations for the model calibration. After dealing with the data issues, we show that the SWAT model could be calibrated with acceptable results for the case study watershed.     

iTree‐Hydro: Snow Hydrology Update For The Urban Forest Hydrology Model1

Yang, Yang, Theodore A. Endreny, and David J. Nowak, 2011. iTree‐Hydro: Snow Hydrology Update for the Urban Forest Hydrology Model. Journal of the American Water Resources Association (JAWRA) 47(6):1211–1218. DOI: 10.1111/j.1752‐1688.2011.00564.x Abstract: This article presents snow hydrology updates made to iTree‐Hydro, previously called the Urban Forest Effects—Hydrology model. iTree‐Hydro Version 1 was a warm climate model developed by the USDA Forest Service to provide a process‐based planning tool with robust water quantity and quality predictions given data limitations common to most urban areas. Cold climate hydrology routines presented in this update to iTree‐Hydro include: (1) snow interception to simulate the capture of snow by the vegetation canopy, (2) snow unloading to simulate the release of snow triggered by wind, (3) snowmelt to simulate the solid to liquid phase change using a heat budget, and (4) snow sublimation to simulate the solid to gas phase via evaporation. Cold climate hydrology routines were tested with research‐grade snow accumulation and weather data for the winter of 1996‐1997 at Umpqua National Forest, Oregon. The Nash‐Sutcliffe efficiency for open area snow accumulation was 0.77 and the Nash‐Sutcliffe efficiency for under canopy was 0.91. The USDA Forest Service offers iTree‐Hydro for urban forest hydrology simulation through http://www.iTreetools.org .     

1960~2019年静海高温天气变化特征分析及日高温概率模型

利用静海国家气象站1960~2019年日最高气温资料对静海高温天气发生的开始和结束时间、次数进行了统计,分析了持续高温天气过程的年际变化规律、时间演变特征,利用Mann-Kendall法对高温日数、年最高气温进行趋势检验;构建了日高温发生概率的“钟形”曲线模型,利用傅里叶变换分析日高温发生概率序列的主要分量,构建了基于傅里叶级数的日高温发生概率简化模型。结果表明:1960年至1996年静海年高温日数呈下降趋势,1997年开始年高温日数呈上升趋势,而年最高气温无显著的上升趋势;静海高温天气过程主要为持续1~2天的过程,近20年高温热浪发生次数明显增加;近60年高温日开始时间提前,结束时间推迟的趋势明显;模型较好的模拟了日高温发生概率的变化特征。     

Spatial and Seasonal Response of Municipal Water Use to Weather across the Contiguous U.S.

Weather variability has the potential to influence municipal water use, particularly in dry regions such as the western United States (U.S.). Outdoor water use can account for more than half of annual household water use and may be particularly responsive to weather, but little is known about how the expected magnitude of these responses varies across the U.S. This nationwide study identified the response of municipal water use to monthly weather (i.e., temperature, precipitation, evapotranspiration [ET]) using monthly water deliveries for 229 cities in the contiguous U.S. Using city‐specific multiple regression and region‐specific models with city fixed effects, we investigated what portion of the variability in municipal water use was explained by weather across cities, and also estimated responses to weather across seasons and climate regions. Our findings indicated municipal water use was generally well‐explained by weather, with median adjusted R² ranging from 63% to 95% across climate regions. Weather was more predictive of water use in dry climates compared to wet, and temperature had more explanatory power than precipitation or ET. In response to a 1°C increase in monthly maximum temperature, municipal water use was shown to increase by 3.2% and 3.9% in dry cities in winter and summer, respectively, with smaller changes in wet cities. Quantifying these responses allows urban water managers to plan for weather‐driven variability in water use.     

Potential Impacts of Climate Change on the Reliability of Water and Hydropower Supply from a Multipurpose Dam in South Korea

Future climate change is a source of growing concerns for the supply of energy and resources, and it may have significant impacts on industry and the economy. Major effects are likely to arise from changes to the freshwater resources system, due to the connection of energy generation to these water systems. Using future climate data downscaled by a stochastic weather generator, this study investigates the potential impacts of climate change on long‐term reservoir operations at the Chungju multipurpose dam in South Korea, specifically considering the reliability of the supply of water and hydropower. A reservoir model, Hydrologic Engineering Center‐Reservoir System Simulation (HEC‐ResSim), was used to simulate the ability of the dam to supply water and hydropower under different conditions. The hydrologic model Soil and Water Assessment Tool was used to determine the HEC‐ResSim boundary conditions, including daily dam inflow from the 6,642 km² watershed into the 2.75 Gm³ capacity reservoir. Projections of the future climate indicate that temperature and precipitation during 2070‐2099 (2080s) show an increase of +4.1°C and 19.4%, respectively, based on the baseline (1990‐2009). The results from the models suggest that, in the 2080s, the average annual water supply and hydropower production would change by +19.8 to +56.5% and by +33.9 to 92.3%, respectively. Model simulations suggest that under the new climatic conditions, the reliability of water and hydropower supply would be generally improved, as a consequence of increased dam inflow.     

1961—2008年新疆阿克苏地区降水、温度变化特征

利用阿克苏地区5个气象站1961—2008年的降水和温度资料,对近50 a来该地区气候变化及其趋势进行了分析。各气象站年降水量变化趋势基本一致,总体上都呈增加趋势。除库车县气象站年平均温度呈降低趋势外,其余呈上升趋势。总体上,阿克苏地区年降水量和年平均温度均呈上升趋势。     

MODELING THE EFFECTS OF URBANIZATION ON BASIN WATER YIELD AND RESERVOIR SEDIMENTATION1

ABSTRACT: The dam impounding White Rock Lake was completed in 1910 to provide water for the City of Dallas. Since then, land use on the watershed has changed from entirely rural to over 77 percent urban. A model called SWRRB (Simulator for Water Resources in Rural Basins) was utilized to determine the effect of urbanization on water and sediment entering the lake. The simulation results show that, if urbanization had not occurred, then the annual surface runoff would be 135 mm rather than 151 mm and the annual sediment yield would be 4.4 t/ha rather than 4.1 t/ha. Also, the effect of urbanization on delivery ratios was shown and a positive linear correlation was found. Finally, the weather generator in SWRRB was utilized to estimate the loss of reservoir capacity until 2050 for three different land use management scenarios.     

STRATIFICATION VARIABILITY IN THREE MORPHOMETRICALLY DIFFERENT LAKES UNDER IDENTICAL METEOROLOGICAL FORCING1

ABSTRACT: Synoptic water temperature measurements were taken in three temperate lakes located within 25 km of one another to study the effects of morphometry (and changes in weather) on seasonal and short-term thermal stratification characteristics. Two of the lakes had nearly the same surface areas and two had nearly identical mean depths; all were exposed to identical weather conditions. The dominance of weather over morphometry on the water surface temperature response was illustrated by the synoptic measurements in two different years. Stratification structure was also found to be dominated by weather for sufficiently deep lakes. Surface area effects were most subtle but explainable as sheltering effects. The onset of stratification was not, as traditionally described, a simple, gradual response of a lake to the annual solar radiation cycle. Rather it depends on a series of alternating heating, cooling, and mixing cycles similar to annual and diel cycles but with a period of approximately five days. These were in direct response to the passage of major weather systems and displayed no apparent time lag. No comparable synoptic water temperature data set could be found in the literature.     

Simulation of vegetation dynamics and management strategies on south Texas, semi-arid rangeland

In this paper, we describe a model designed to simulate seasonal dynamics of warm and cool season grasses and forbs, as well as the dynamics of woody plant succession through five seral stages, in each of nine different plant communities on the Rob and Bessie Welder Wildlife Refuge. The Welder Wildlife Refuge (WWR) is located in the Gulf Coastal Prairies and Marshes ecoregion of Texas. The model utilizes and integrates data from a wide array of research projects that have occurred in south Texas and WWR. It is designed to investigate the effects of alternative livestock grazing programs and brush control practices, with particular emphasis on prescribed burning, the preferred treatment for brush on the WWR. We evaluated the model by simulating changes in the plant communities under historical (1974-2000) temperature, rainfall, livestock grazing rotation, and brush control regimes, and comparing simulation results to field data on herbaceous biomass and brush canopy cover collected on the WWR over the same period. We then used the model to simulate the effects of 13 alternative management schemes, under each of four weather regimes, over the next 25 years. We found that over the simulation period, years 1974-2000, the model does well in simulating the magnitude and seasonality of herbaceous biomass production and changes in percent brush canopy cover on the WWR. It also does well in simulating the effects of variations in cattle stocking rates, grazing rotation programs, and brush control regimes on plant communities, thus providing insight into the combined effects of temperature, precipitation, cattle stocking rates, grazing rotation programs, and brush control on the overall productivity and state of woody plant succession on the WWR. Simulation of alternative management schemes suggests that brush canopy removal differs little between summer and winter prescribed burn treatments when precipitation remains near the long-term average, but during periods of low precipitation canopy removal is greater under winter prescribed burning. The model provides a useful tool to assist refuge personnel with developing long-term brush management and livestock grazing strategies.     

Historical and Future Stream Temperature Change Predicted by a Lidar‐Based Assessment of Riparian Condition and Channel Width

Riparian forests attenuate solar radiation, thereby mediating an important component of the thermal budget of streams. Here, we investigate the relationship between riparian degradation, stream temperature, and channel width in the Chehalis River Basin, Washington State. We used lidar data to measure canopy opening angle, the angle formed between the channel center and trees on both banks; we assumed historical tree heights and calculated the change in canopy angle relative to historical conditions. We then developed an empirical relationship between canopy angle and water temperature using existing data, and simulated temperatures between 2002 and 2080 by combining a tree growth model with climate change scenarios from the NorWeST regional prediction. The greatest change between historical and current conditions (~7°C) occurred in developed portions of the river network, with the highest values of change predicted at channel widths less than ~40 m. Tree growth lessened climate change increases in maximum temperature and the length of river exceeding biologically critical thresholds by ~50%–60%. Moreover, the maximum temperature of channels with bankfull widths less than ~50 m remained similar to current conditions, despite climate change increases. Our findings are consistent with a possible role for the riparian landscape in explaining the low sensitivity of stream temperatures to air temperatures observed in some small mountain streams.     

ANALYSIS AND MODELING OF LONG-TERM STREAM TEMPERATURES ON THE STEAMBOAT CREEK BASIN,OREGON: IMPLICATIONS FOR LAND USE AND FISH HABITAT1

ABSTRACT: Steamboat Creek basin is an important source of timber and provides crucial spawning and rearing habitat for anadromous steelhead trout (Oncorhynchus mykiss). Because stream temperatures are near the upper limit of tolerance for the survival of juvenile steelhead, the possible long-term effect of clear-cut logging on stream temperatures was assessed. Twenty-year (1969–1989) records of summer stream temperature and flow from four tributaries and two reaches of Steamboat Creek and Boulder Creek (a nearby unlogged watershed) were analyzed. Logging records for the Steamboat Creek basin and air temperature records also were used in the analysis. A time-series model of the components of stream temperature (seasonal cycle of solar radiation, air temperature, streamflow, an autoregressive term of order 1, and a linear trend variable) was fitted to the water-temperature data. The linear trend variable was significant in all the fitted models except Bend Creek (a tributary fed by cool ground-water discharge) and Boulder Creek. Because no trends in either climate (i.e., air temperature) or streamflow were found in the data, the trend variable was associated with the pre-1969 loss and subsequent regrowth of riparian vegetation and shading canopies.     

A Risk-Based Approach to Evaluating Wildlife Demographics for Management in a Changing Climate: A Case Study of the Lewis’s Woodpecker

Given the projected threat that climate change poses to biodiversity, the need for proactive response efforts is clear. However, integrating uncertain climate change information into conservation planning is challenging, and more explicit guidance is needed. To this end, this article provides a specific example of how a risk-based approach can be used to incorporate a species’ response to climate into conservation decisions. This is shown by taking advantage of species’ response (i.e., impact) models that have been developed for a well-studied bird species of conservation concern. Specifically, we examine the current and potential impact of climate on nest survival of the Lewis’s Woodpecker (Melanerpes lewis) in two different habitats. To address climate uncertainty, climate scenarios are developed by manipulating historical weather observations to create ensembles (i.e., multiple sequences of daily weather) that reflect historical variability and potential climate change. These ensembles allow for a probabilistic evaluation of the risk posed to Lewis’s Woodpecker nest survival and are used in two demographic analyses. First, the relative value of each habitat is compared in terms of nest survival, and second, the likelihood of exceeding a critical population threshold is examined. By embedding the analyses in a risk framework, we show how management choices can be made to be commensurate with a defined level of acceptable risk. The results can be used to inform habitat prioritization and are discussed in the context of an economic framework for evaluating trade-offs between management alternatives.     

IMPACTS OF CLIMATE CHANGE ON WATER YIELD IN THE UPPER WIND RIVER BASIN1

ABSTRACT: The potential impacts of climate change on water yield are examined in the Upper Wind River Basin. This is a high‐elevation, mountain basin with a snowfall/snowmelt dominated stream‐flow hydrograph. A variety of physiographic conditions are represented in the rangeland, coniferous forests, and high‐elevation alpine regions. The Soil Water Assessment Tool (SWAT) is used to model the baseline input time series data and climate change scenarios. Five hydroclimatic variables (temperature, precipitation, CO₂, radiation, and humidity) are examined using sensitivity tests of individual and coupled variables with a constant change and coupled variables with a monthly change. Results indicate that the most influential variable on annual water yield is precipitation; and, the most influential variable on the timing of streamflow is temperature. Carbon dioxide, radiation, and humidity each noticeably impact water yield, but less significantly. The coupled variable analyses represent a more realistic climate change regime and reflect the combined response of the basin to each variable; for example, increased temperature offsets the effects of increased precipitation and magnifies the effects of decreased precipitation. This paper shows that the hydrologic response to climate change depends largely on the hydroclimatic variables examined and that each variable has a unique effect (e.g., magnitude, timing) on water yield.     

Riparian Ecosystem Management Model: Sensitivity to Soil,Vegetation, and Weather Input Parameters1

Abstract: The Riparian Ecosystem Management Model (REMM) was developed by the U.S. Department of Agriculture‐Agriculture Research Service (USDA‐ARS) and its cooperators to design and evaluate the efficiency of riparian buffer ecosystems for nonpoint source pollution reduction. REMM requires numerous inputs to simulate water movement, sediment transport, and nutrient cycling in the buffer system. In order to identify critical model inputs and their uncertainties, a univariate sensitivity analysis was conducted for nine REMM output variables. The magnitude of each input parameter was changed from ?50% to +50% from the baseline data in 12 intervals or, in some cases, the complete range of an input was tested. Baseline model inputs for the sensitivity analysis were taken from Gibbs Farm, Georgia, where REMM was tested using a 5‐year field dataset. Results of the sensitivity analysis indicate that REMM responses were most sensitive to weather inputs, with minimum daily temperature having the greatest impact on the nitrogen‐related outputs. For example, the 100% change (?50% to +50%) in minimum daily temperature input values yielded a 164.4% change in total nitrogen (N), a 109.3% change in total nitrate (NO₃), and a 127.1% change in denitrification. REMM was most sensitive to precipitation with regard to total flow leaving the riparian vegetative buffer zone (199.8%) and sediment yield (138.2%). Deep seepage (12.2%), volumetric water content (24.8%), and pore size index (6.5%) in the buffer soil profile were the most influential inputs for the output water movement. Sediment yield was most sensitive to Manning’s coefficient (46.6%), bare soil percent (40.7%), and soil permeability (6.1%). For vegetation, specific leaf area, growing degree day coefficients, and maximum root depth influenced the nitrogen related outputs. Overall results suggest that because of the high sensitivity to weather parameters, on‐site weather data is needed for model calibration and validation. The model’s relatively low sensitivity to vegetation parameters also appears to support the use of regional vegetation datasets that would simplify model implementation without compromising results.     

Uncertainty assessment of the model RICEWQ in northern Italy

Model predictions are often seriously affected by uncertainties arising from many sources. Ignoring the uncertainty associated with model predictions may result in misleading interpretations when the model is used by a decision-maker for risk assessment. In this paper, an analysis of uncertainty was performed to estimate the uncertainty of model predictions and to screen out crucial variables using a Monte Carlo stochastic approach and a number of statistical methods, including ANOVA and stepwise multiple regression. The model studied was RICEWQ (Version 1.6.1), which was used to forecast pesticide fate in paddy fields. The results demonstrated that the paddy runoff concentration predicted by RICEWQ was in agreement with field measurements and the model can be applied to simulate pesticide fate at field scale. Model uncertainty was acceptable, runoff predictions conformed to a log-normal distribution with a short right tail, and predictions were reliable at field scale due to the narrow spread of uncertainty distribution. The main contribution of input variables to model uncertainty resulted from spatial (sediment-water partition coefficient and mixing depth to allow direct partitioning to bed) and management (time and rate of application) parameters, and weather conditions. Therefore, these crucial parameters should be carefully parameterized or precisely determined in each site-specific paddy field before the application of the model, since small errors of these parameters may induce large uncertainty of model outputs.     

Simulation of Temperature Mitigation by a Stormwater Detention Pond1

Abstract: A numerical model has been developed to simulate the hydraulic and heat transfer properties of a stormwater detention pond, as part of a simulation tool to evaluate thermal pollution of coldwater streams from stormwater runoff. The model is dynamic (unsteady) and based on principles of fluid mechanics and heat transfer. It is driven by hourly weather data, and specified inflow rates and temperatures. To calibrate and validate the pond model field data were collected on a commercial site in Woodbury, Minnesota. The relationship between pond inflow and outflow rates to precipitation was effectively calibrated using continuously recorded pond levels. Algorithms developed for surface heat transfer in lakes were found to be applicable to the pond with some modification, resulting in agreement of simulated and observed pond surface temperature within 1.0°C root mean square error. The use of an unshaded pond for thermal mitigation of runoff from paved surfaces was evaluated using the pond model combined with simulated runoff from an asphalt parking lot for six years of observed rainfall events. On average, pond outflow temperature was 1.2°C higher than inflow temperature, but with significant event‐to‐event variation. On average, the pond added heat energy to runoff from an asphalt parking lot. Although the pond added total heat energy to runoff, it did reduce the rate of heat outflow from the pond by an order of magnitude due to reductions in volumetric outflow rate compared with the inflow rate. By reducing the rate of heat flow, the magnitude of temperature impacts in a receiving stream were also reduced, but the duration of impacts was increased.     

ESTIMATION OF WATER TEMPERATURE EXCEEDANCE PROBABILITIES USING THERMO-HYDRODYNAMIC MODELING1

ABSTRACT: A continuous simulation approach is proposed for estimating water temperature exceedance probabilities using thermo-hydrodynamic modeling. The approach uses (1) a deterministic unsteady flow and heat transport model, (2) continuous hydrological and meteorological data for a long historical period, and (3) synthetic records of tributary water temperatures and other model inputs. Representative historical records of streamflow, air temperatures, and other hydrometeorological variables are obtained from nearby gages. Stochastic modeling methods are used to construct synthetic records for other model inputs, including inflow water temperatures. An application of this deterministic-stochastic approach is presented for a complex waterway in northeastern Illinois with heat discharges from several power plants and wastewater treatment plants. Statistical results from the continuous simulations are compared to results obtained from traditional event simulations. The application illustrates the information that engineers and biologists can obtain for (1) evaluating compliance with water temperature standards, and (2) assessing the effect of water temperatures on aquatic habitat.