A combined radical and non-radical oxidation processes for efficient degradation of Acid Orange 7 in the homogeneous Cu(II)/PMS system: important role of chloride

Environmental Science and Pollution Research - Trace copper ion (Cu(II)) in water and wastewater can trigger peroxymonosulfate (PMS) activation to oxidize organic compounds, but it only works under...     

Heat dissipation characteristic in the intake grille and radiator of a fuel cell vehicle

ABSTRACT

In this study, a three-dimension (3D) computational model was proposed to investigate the flow and heat transfer characteristics of the intake grilles of two different fuel cell vehicles. The models of the intake grilles were constructed according to the actual sizes of two vehicles, namely, Roewe 950 and Toyota Mirai, considering the heat dissipation unit to simplify the heat transfer model of the vehicle. The results showed that relative to Roewe 950, Mirai intake air flow rate was approximately 10% higher, the heat transfer capacity was approximately 7% higher, and the intake grille area was larger. The coolant outlet temperature of Mirai was lower than that of Roewe 950, which was beneficial for the long term and stable operation of a fuel cell. This comparative study provided guidance for the intake grille and radiator design of fuel cell vehicles. The only difference between fuel cell vehicles on the market and conventional vehicles was that in the former, the internal combustion engine was replaced with a fuel cell stack, which had insufficient heat transfer capacity because of the reducing temperature difference. Increasing the intake grille area and the heat exchange capacity of the radiator were the key issues for the development of fuel cell vehicles. In this study, an optimal window opening angle of the radiator fin of 23° provided a maximal heat transfer coefficient.     

Design and validation of a practical index for trauma assessment

In the past 20 years a variety of indices have been suggested for measuring the severity of trauma, however none of them meets the requirement of being a simple and objective instrument that can be utilized efficiently by lay persons and providers of health services without previous experience in triaging. A new system has been proposed which meets this requirement and which has been validated with 197 injured persons at the emergency ward of the Valle University Hospital in Call, Colombia. The instrument showed a high level of concordance with the conventional triaging method and classifies victims into four categories: critical with recovery unlikely, critical but recoverable, moderately serious, and ambulatory. There is discussion on the reliability of this instrument and it is recommended that it be validated with victims from larger disasters. Regardless, it has the advantage of being specific and free of the subjectivity that characterizes other indices.     

Analysis of pollutant levels in central Hong Kong applying neural network method with particle swarm optimization

Air pollution has emerged as an imminent issue in modernsociety. Prediction of pollutant levels is an importantresearch topic in atmospheric environment today. For fulfillingsuch prediction, the use of neural network (NN), and inparticular the multi-layer perceptrons, has presented to be acost-effective technique superior to traditional statisticalmethods. But their training, usually with back-propagation (BP)algorithm or other gradient algorithms, is often with certaindrawbacks, such as: 1) very slow convergence, and 2) easilygetting stuck in a local minimum. In this paper, a newlydeveloped method, particle swarm optimization (PSO) model, isadopted to train perceptrons, to predict pollutant levels, andas a result, a PSO-based neural network approach is presented. The approach is demonstrated to be feasible and effective bypredicting some real air-quality problems.     

Speciation of arsenic using solid phase extraction cartridges

Various solid phase extraction (SPE) cartridges were investigated for speciation of arsenite [As(III)], arsenate [As(v)], monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA). Cartridges containing different types of sorbent materials were tested for arsenic retention and elution characteristics. Alumina cartridges were found to completely retain all the four target arsenic species, and are suitable for removal and preconcentration purposes. For speciation analysis, different arsenic species were separated on the basis of their selective retention on and elution from specific cartridges. DMA was retained on a resin-based strong cation exchange cartridge and eluted with 1.0 M HCl. MMA and As(v) were both retained on a silica-based strong anion exchange cartridge and sequentially eluted with 60 mM acetic acid (for MMA) and 1.0 M HCl [for As(v)]. As(III) was not retained on either cartridge and remained in solution. Arsenic species in solution and those eluted from the cartridges were subsequently quantified by using flow injection with hydride generation atomic fluorescence spectrometry (FI-HGAFS) and hydride generation atomic absorption spectrometry (FI-HGAAS). A detection limit of 0.05 microg L(-1) arsenic in water sample was achieved using HGAFS. An application of the method was demonstrated at a drinking water treatment facility. As(III) and As(v) species were determined in water at various stages of treatment. The method is suitable for routine determination of trace levels of arsenic in drinking water to comply with more stringent environmental regulations.     

Measurements of fractionated gaseous mercury concentrations over northwestern and central Europe, 1995-99

Although it makes up only a few per cent. of total gaseous mercury (TGM) in the atmosphere, the fraction of oxidised (divalent) mercury plays a major role in the biogeochemical cycle of mercury due to its high affinity for water and surfaces. Quantitative knowledge of this fraction present in mixing ratios in the parts-per-10(15) (ppq) range is currently very scarce. This work is based on approximately 220 data for divalent gaseous mercury (DGM) collected during 1995-99 in ambient air. Over the course of the measurements, the sampling and analytical methods were modified and improved. This is described here in detail and includes transition from wet leaching and reduction procedures to thermo-reductive desorption, the use of annular as well as tubular denuders and adoption of an automated sampling system. The concentration of DGM exhibited a strong seasonal behaviour in contrast to atomic gaseous mercury, with low values in winter and maximum values in summer. The DGM/TGM ratios were frequently found to be below the detection limit (< or = 1%) and in the range 1-5%. A trend of diurnal DGM patterns was observed and implies photolytically induced sources. Scavenging of DGM during rain events was also noticed.     

Soil properties and crop productivity as influenced by flyash incorporation in soil

Field experiments were carried out during 1996–97at Gulawathi, Muthiani and Salarpur Villages, IARI Farm, NewDelhi and NCPP Campus, Dadri to evaluate changes in soilcharacteristics and growth of wheat (Triticum aestivum L.),mustard (Brassica juncea L.), lentil (Lence esculentaMoench.), rice (Oryza sativa L.) and maize (Zea mays L.) byvarying amounts of flyash addition (up to 50t ha^-1) in soils atsowing/transplanting time of crops. Flyash addition in areasadjoining NCPP Thermal Power Plant, Dadri, Ghaziabad, U.P.ranged from 5–12 t ha^-1 yr^-1 in 1995–96. Shoot and root growthand yield of test crops at different locations after flyashincorporation resulted in beneficial effects of flyashaddition in most cases. The silt dominant texture of flyashimproved loamy sand to sandy loam textures of the surfacesoils at the farmers' fields. The increased growth in yield ofcrops with flyash incorporation was possibly due tomodifications in soil moisture retention and transmissioncharacteristics, bulk density, physico-chemical characterssuch as pH and EC and organic carbon content. The response offlyash addition in the soil on soil health and cropproductivity needs to be evaluated on long-term sustainableaspects.     

高职电子技术课程改革探讨

本文首先分析了高等职业教育电子技术课程的传统教学方式和弊端，随后探讨了电子技术教学的改革途径：包括高职教材内容的修订和更新，通过多媒体技术与EDA技术改善电子技术的课堂教学；精选验证性实验及强化EDA技术在实验和设计环节中的比例等多方面措施。     

Mercury consumption and contamination of environment in gold mining in China

1　ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｇｏｌｄｉｎｄｕｓｔｒｙｉｎＣｈｉｎａｇｒｏｗｓｕｐｑｕｉｃｋｌｙｗｉｔｈｔｈｅｇｒｏｗｔｈｒａｔｅｏｆａｂｏｕｔ 10 %ｓｉｎｃｅ 90’ｓ.Ｉｎ 1995,ｔｈｅｐｒｏｄｕｃｔｉｏｎｏｆｇｏｌｄｗａｓｏｖｅｒ10 0ｔｏｎｓ/ａ,ａｎｄｉｎ 1996ｒｅａｃｈｅｄ 12 0ｔｏｎｓ/ａ .Ｉｔｉｓｒａｎｋｅｄｓｉｘｔｈｉｎｔｈｅｗｏｒｌｄ(Ｃｈａｎｇ ,1995) .Ｔｈｅｉｒｍａｉｎｐｒｏｃｅｄｕｒｅｓｏｆｇｏｌｄｅｘｔｒａｃｔｉｏｎａｒｅ :(1)ｃｙａｎｉｚａｔｉｏｎｉｎｔｏｔａｌｏｒｅ ｃａｒｂｏ…     

半导体制造业的环境污染与清洁生产

在分析半导体制造过程中不同工艺产生的环境污染问题的基础上，讨论了半导体制造业开展清洁生产的原则和途径，介绍了一些成功的清洁生产方案。