Heat dissipation characteristic in the intake grille and radiator of a fuel cell vehicle

ABSTRACT

In this study, a three-dimension (3D) computational model was proposed to investigate the flow and heat transfer characteristics of the intake grilles of two different fuel cell vehicles. The models of the intake grilles were constructed according to the actual sizes of two vehicles, namely, Roewe 950 and Toyota Mirai, considering the heat dissipation unit to simplify the heat transfer model of the vehicle. The results showed that relative to Roewe 950, Mirai intake air flow rate was approximately 10% higher, the heat transfer capacity was approximately 7% higher, and the intake grille area was larger. The coolant outlet temperature of Mirai was lower than that of Roewe 950, which was beneficial for the long term and stable operation of a fuel cell. This comparative study provided guidance for the intake grille and radiator design of fuel cell vehicles. The only difference between fuel cell vehicles on the market and conventional vehicles was that in the former, the internal combustion engine was replaced with a fuel cell stack, which had insufficient heat transfer capacity because of the reducing temperature difference. Increasing the intake grille area and the heat exchange capacity of the radiator were the key issues for the development of fuel cell vehicles. In this study, an optimal window opening angle of the radiator fin of 23° provided a maximal heat transfer coefficient.     

碘化阶层孔氧化硅纳米球对水中典型有机氯污染物的吸附性能研究

采用共缩聚法,成功地原位合成了碘改性的阶层多孔氧化硅纳米球（SiO₂-I）,研究了其基于卤键作用对典型有机氯污染物六六六的吸附性能,并考察了改性剂I-硅烷含量和pH值对吸附效果的影响.实验结果表明,该纳米材料对六六六表现出优异的吸附富集性能,吸附速率快,60 min内对六六六的去除率为71.6%,240 min内达到吸附平衡,去除率可达98.3%,最大吸附量为178.6 mg·g^-1;吸附动力学符合拟二级动力学模型;碘物种的加入提高了阶层多孔氧化硅的吸附速率和吸附效率.另外,为了便于纳米吸附材料的分离,本研究对SiO₂-I纳米球进行了磁性化.研究发现,磁性化修饰后,SiO₂-I纳米材料仍然保留对六六六优异的吸附富集性能,240 min时的吸附去除率达90.3%.     

酸性紫色水稻土颗粒有机质对镉的吸附特性

采集典型的酸性紫色水稻土（APPS）,从中分离出颗粒有机质（POM）,通过批量试验研究POM及其来源土壤Cd²⁺的吸附动力学、等温吸附和热力学特征,通过扫描电镜-能谱仪、傅里叶红外光谱仪等手段及吸附前后镉的形态变化的测定,研究了POM对Cd²⁺的吸附机制.结果表明：POM对Cd²⁺的亲和力远高于其来源土壤.POM及土壤对Cd²⁺的吸附动力学最优模型均为准二级动力学.Langmuir、Freundlich方程均能较好地描述其等温吸附特征,其中对POM,以Freundlich方程更优,表明POM对Cd²⁺的吸附属于多分子层的非均质吸附.吸附热力学参数△G^θ均小于0、△H^θ和△S^θ均大于0,表明吸附属于自发吸热过程.根据△H^θ值及解吸试验判定POM对Cd²⁺的吸附以化学吸附为主,土壤对Cd²⁺的吸附过程以物理吸附为主.吸附平衡后,土壤中可交换态镉比例提高,而POM中交换态和络合态镉比例增加.综上及吸附前后POM的表征结果说明,POM对Cd²⁺的吸附机制包括含氧官能团的络合、离子交换、阳离子-π键、沉淀作用和静电吸附.     

内饰材料发射率对密封舱室热防护效率的影响

目的探究密封舱室热防护效率与其内饰材料表面发射率的关系,分析内饰材料发射率对其表面温度、舱室内温度的影响规律。方法采用自行设计的小型密封舱室和加热测量装置,对内饰材料表面及舱室内温度进行测量。结果当内饰材料发射率为0.09时,内饰表面温度为141.2℃,舱室内平均温度仅为90.8℃;内饰材料发射率为0.91时,内饰表面温度为124.4℃,舱室内平均温度为109.1℃。结论试样表面温度随材料发射率的提高而降低,舱室内部空气平均温度随材料发射率的提高而升高;试样表面温度与舱室空气平均温度的温度差随材料发射率的提高而减小;同时,相同试样表面温度与舱室平均温度的温度差随加热温度的提高而增加。     

硅胶表面TEOS疏水化改性及吸附VOCs特性

以正硅酸乙酯（TEOS）为疏水改性剂,通过硅胶表面的羟基接枝反应,得到具备一定疏水性的改性硅胶;利用BET、FT-IR、XRD和TG-DTG等手段对改性硅胶的结构及稳定性进行了表征;在此基础上考察了改性硅胶对各类有机废气的吸附性能.结果表明,TEOS成功接枝在了硅胶表面,改性硅胶不仅具备一定的疏水性,而且机械强度增加到原来的66.85%,稳定性也都得到了提高; 550℃空气下焙烧后的改性硅胶仍具有疏水性且吸附容量是焙烧之前的2倍;在高湿度高浓度的废气治理中,TEOS改性硅胶表现出更高的吸附能力和优良的热再生性能.高浓度下改性硅胶的吸附容量是低浓度下的10倍且不受水汽的影响;改性硅胶循环10次的吸附/脱附几乎不变,且在一定条件下,15~30min就达到90%的脱附率.     

磁性有序介孔碳的制备及其对水中双酚A的吸附

采用水热法成功制备了磁性有序介孔碳（Fe-OMC）,用于吸附水中双酚A （BPA）.采用高倍投射电镜、X射线衍射仪、傅里叶红外光谱仪、比表面积分析仪和振动样品磁强计对Fe-OMC进行表征.结果表明,该吸附剂具备较大的比表面积、独特的有序介孔孔道结构、丰富的含氧官能团以及较强的超顺磁性.Fe-OMC能够高效地吸附去除水中的BPA,平衡吸附量可达72.62mg/g,经过外加磁场分离回收后依旧具备较好的吸附性能.随着BPA浓度从1mg/L提高到20mg/L,其平衡吸附量由8.33mg/g增至91.78mg/g.随着pH值的升高呈现出先降低后升高再降低的趋势,最高吸附量出现在pH=8（75.34mg/g）.Fe-OMC对BPA的吸附过程可用准二级吸附动力学模型和Langmuir吸附等温模型进行描述.计算的热力学参数表明,Fe-OMC对BPA的吸附过程是自发进行的放热过程.     

基于铁锰泥的除砷吸附剂性能比较及吸附机理

为解决反冲洗铁锰泥粉末吸附剂（BSPA）使用后难以泥水分离问题,将除铁锰水厂生物滤池产生的反冲洗泥制成颗粒吸附剂（GA）和磁性粉末吸附剂（MPA）,并对BSPA、GA和MPA的除砷性能进行了比较,通过SEM、TED、XRD、BET、FTIR等技术对3种材料进行了表征,寻找3种吸附剂之间除砷性能差异的根源.结果表明,BSPA、GA和MPA对As （V）的最大吸附容量分别为40.980,5.048,8.694mg/g,改性后的吸附材料GA和MPA对砷的吸附能力下降.BSPA是一种以纤铁矿为主的无定形结构混合物,并混有针铁矿和结晶度差的水铁矿,GA的XRD图谱中出现石英晶体和少量赤铁矿晶体的衍射峰,而MPA的主要成分为结晶程度较高的磁赤铁矿.3种材料中均存在有利于吸附的含羟基官能团.BSPA、MPA和GA的比表面积分别为253.150,238.660,43.803m²/g.物相改变且结晶程度增加、表面羟基减少和比表面积降低是导致GA和MPA的砷吸附容量比BSPA低的主要因素.     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

汕头港水域温排水热扩散的三维数值模拟

本文建立了汕头港水域温排水扩散的三维数学模型，并采用特征差分方法求其解，对该法在三维情况下的稳定作了推导，给出了判断公式，上述模型被应用于汕头热电厂废热水排放的环境影响评价中，实例计算表明，该模型算法程序简单，计算结果合理。     

火焰原子吸收分光光度法测定水中锶

研究了用空气/乙炔火焰原子吸收分光光度法测定水中锶时酸的影响,以及铝和钙的干扰及消除,线性范围0.05～5.00mg/l,最低检测浓度为0.04mg/l,回收率为98.2％～101.4％。