循环载荷下煤裂隙演化试验研究

为了研究循环载荷下的煤体裂隙演化特征,在不同应力水平和不同频率条件下分别进行煤样破坏力学及声发射试验。结果表明:应力-应变曲线呈疏-密-疏的变化特征,对应的振铃数柱状图呈U型;上限应力点的应变值、累积能量、撞击计数均随循环次数增加而上升,曲线呈倒S型;煤裂隙演化经历了原始裂隙闭合、新生裂隙稳定发育和裂纹贯穿破坏等3个不同阶段;循环载荷的应力水平和加载频率对煤体疲劳寿命的影响具有差异性,对煤体裂隙演化和破坏模式均有明显影响。     

分段变速加载对含瓦斯突出煤力学特性影响试验研究

为探究采动应力变化对含瓦斯突出煤力学特性的影响,利用RLW-500G煤岩三轴蠕变-渗流试验系统,对新景矿含瓦斯突出煤进行了不同围压和瓦斯压力下的常规三轴和分段变速加载力学试验。结果表明:煤样在2种应力路径下的全应力应变曲线均可分为压密、线弹性、塑性变形、应力跌落和残余应力5个阶段;随着围压的升高或者瓦斯压力的降低,煤体在2种应力路径下的强度和弹性模量均增大;相较于常规三轴,煤体在分段变速加载路径下的强度普遍增大,峰值轴向应变、峰值环向应变绝对值和峰值体积应变绝对值也普遍增大,失稳破坏瞬间应力跌落和能量释放更加剧烈。Mohr-Coulomb强度准则仍然适用于分段变速加载条件下的含瓦斯突出煤,该研究对于认识煤与瓦斯突出的发生机制具有一定的指导意义。     

不同自燃倾向性煤的指标气体产生规律实验研究

为研究不同自燃倾向性煤的自燃指标气体变化规律,提高对煤早期自燃预测预报的准确度,采用程序升温实验系统,得到内蒙古褐煤、神东长焰煤、河南气煤及枣庄焦煤4种不同变质程度煤的氧化时间随温度的变化关系,以及指标气体浓度在煤氧化过程中的变化规律。结果表明:自燃倾向性最高的褐煤应以CO和乙烯作为煤自燃早期预报的首选指标气体;易自燃的长焰煤应采用乙烯和烯烷比为主、以CO为辅的煤自燃判定指标;自燃倾向性较低的气煤应以乙烯和烯烷比作为煤自燃预报指标;CO是自燃倾向性最低的焦煤的最佳自燃预报指标气体。     

平煤十矿底板巷穿层钻孔瓦斯抽采模拟研究

为了降低平煤十矿己15-16-24130工作面运输巷掘进中的突出危险性,基于实际工程背景,考虑瓦斯抽采中的瓦斯运移及煤岩变形等因素,建立了瓦斯抽采气固耦合模型,并利用COMSOL Multiphysics软件对平煤十矿己15-16煤层的底板巷穿层钻孔瓦斯抽采方案进行数值模拟,研究了瓦斯抽采对于降低掘进过程中突出危险性的影响。研究结果表明:在己18煤层开挖底板巷对己15-16煤层进行穿层钻孔瓦斯抽采,瓦斯抽采180 d后,己15-16-24130工作面运输巷附近煤层残余瓦斯压力及瓦斯含量分别降至0.315 MPa和3.84 m3/t;将底板巷穿层钻孔瓦斯抽采方案进行工程应用,实测抽采后的残余瓦斯压力及瓦斯含量在0.32 MPa和3.17 m3/t,均小于平煤十矿煤与瓦斯突出防治规定的“双6”指标（残余瓦斯压力小于0.6 MPa,残余瓦斯含量小于6 m3/t）,可有效降低运输巷掘进过程中的突出危险性。     

煤与瓦斯共采在错层位巷道布置中的机理研究及应用构想

为了完善现有煤与瓦斯共采技术,创新煤与瓦斯共采方法,对错层位巷道布置下的煤与瓦斯共采系统展开研究,利用相似模拟试验,分析错层位巷道布置覆岩运动情况,预测其开采围岩裂隙发育和瓦斯运移形式,提出了创新煤与瓦斯共采技术构想。研究结果表明:采空区覆岩三带高度随接续工作面的增加而增大,相邻采空区垮落矸石压实区呈现“O-L-O”形变化,多个相邻采空区覆岩出现大“O”形圈裂隙带;相邻采空区内瓦斯可实现相互运移,大“O”形圈裂隙带内赋存大量瓦斯气体;研究提出了地面钻井抽采瓦斯、走向高位瓦斯抽采巷和外错尾巷穿层钻孔3种煤与瓦斯共采技术,比传统巷道布置情况下的煤与瓦斯共采技术在安全、经济等方面更具优势。     

不同煤层煤氧化自燃性实验分析

为研究不同煤层煤自然发火特征的异同性及规律,以淮南矿区1号、3号、6号、13号煤层为研究对象,通过自然发火实验,对不同煤层煤的自然发火期周期、煤样70℃时放热强度和R70值进行分析。研究结果表明:4个不同煤层煤样自燃性由强到弱依次为:3煤>6煤>1煤>13煤;变质程度相近的4个煤层,3煤自然发火期最短,这与煤体中硫分和水分含量高有关;13煤变质程度较高,且前期放热强度、耗氧速率增长缓慢,其自燃性较弱;4个不同煤层煤的耗氧速率、CO,CO2产生率,以及C2H4/C2H6值随煤温升高具有相似的变化规律;煤中CH4气体大量解吸出现于煤温60℃之前,煤中灰分在80~120℃开始逐渐吸热融化,解析和融化均会抑制煤氧接触并且减小煤氧反应放热总量。     

武汉市秋季PM2.5中硫酸盐、硝酸盐理化特征及影响因素

为了解武汉市秋季PM_(2.5)中硫酸盐、硝酸盐理化特征,2016年9—11月利用热还原法在线连续监测分析系统对此进行了采样分析,并同步收集气象因子和离子色谱方法监测结果。结果表明,硫酸盐、硝酸盐的热还原分析方法与离子色谱法的相关系数分别为0.88、0.94;PM_(2.5)中硫酸盐、硝酸盐的水溶性部分占比达92.5%,难溶性部分为7.5%;空气质量为优、良和轻度污染时,硫酸盐、硝酸盐与PM_(2.5)的占比分别为45%、42%、45%;硫酸盐、硝酸盐在降水日和非降水日平均质量浓度分别为(19.6±18.5)μg/m~3和(31.0±9.1)μg/m~3;硝酸盐与硫酸盐的质量比为1.1,高于国内其他城市,与武汉市机动车保有量大幅增加有关。     

pH对煤泥水絮凝沉降的影响

选择聚合氯化铝(PAC)/阴离子型聚丙烯酰胺(PHP)、氯化钙(CaCl2)/非离子型聚丙烯酰胺(NPAM)组合与NPAM、PHP、两性离子型聚丙烯酰胺(ZPAM)作为絮凝剂,在对道清选煤厂水采筛下原生煤泥和浮选尾矿的煤泥水进行组合药剂絮凝实验的基础上,考察了pH对煤泥水絮凝沉降的影响。实验结果表明,在不同的pH下,煤泥水的絮凝效果不同:在酸性条件下,宜单独使用有机高分子絮凝剂;在中性至碱性条件下,无机凝聚剂和有机絮凝剂联合使用效果较好。     

Potential effects of particulate matter from combustion during services on human health and on works of art in medieval churches in Cyprus

Indoor and outdoor particulate matter (PM_0.3-10) number concentrations were established in two medieval churches in Cyprus. In both churches incense was burnt occasionally during Mass. The highest indoor PM_0.5-1 concentrations compared with outdoors (10.7 times higher) were observed in the church that burning of candles indoors was allowed. Peak indoor black carbon concentration was 6.8 μg m⁻³ in the instances that incense was burning and 13.4 μg m⁻³ in the instances that the candles were burning (outdoor levels ranged between 0.6 and 1.3 μg m⁻³). From the water soluble inorganic components determined in PM₁₀, calcium prevailed in all samples indoors or outdoors, whilst high potassium concentration indoors were a clear marker of combustion. Indoor sources of PM were clearly identified and their emission strengths were estimated via modeling of the results. Indoor estimated PM_0.3-10 mass concentrations exceeded air quality standards for human health protection and for the preservation of works of art.     

Appraisal of measurement methods, chemical composition and sources of fine atmospheric particles over six different areas of Northern Belgium

Daily and seasonal variation in the total elemental, organic carbon (OC) and elemental carbon (EC) content and mass of PM_2.5 were studied at industrial, urban, suburban and agricultural/rural areas. Continuous (optical Dustscan, standard tapered element oscillating micro-balance (TEOM), TEOM with filter dynamics measurement system), semi-continuous (Partisol filter-sampling) and non-continuous (Dekati-impactor sampling and gravimetry) methods of PM_2.5 mass monitoring were critically evaluated. The average elemental fraction accounted for 2-6% of the PM_2.5 mass measured by gravimetry. Metals, like K, Mn, Fe, Cu, Zn and Pb were strongly inter-correlated, also frequently with non-metallic elements (P, S, Cl and/or Br) and EC/OC. A high OC/EC ratio (2-9) was generally observed. The total carbon content of PM_2.5 ranged between 3 and 77% (averages: 12-32%), peaking near industrial/heavy trafficked sites. Principal component analysis identified heavy oil burning, ferrous/non-ferrous industry and vehicular emissions as the main sources of metal pollution.