Adsorption studies on coir pith for heavy metal removal

Biosorption efficiency of coir pith, a waste product from coir industry, was investigated in this study for the removal of metallic pollutants such as Ni, Cu and Zn from aqueous solutions. The disposal of coir pith is a major problem associated with the coir industries, especially working in the small-scale sector. The present study explores the effectiveness of utilization of coir pith, an accumulating waste, as a biosorbent for heavy metal removal. Batch mode studies were done to evaluate the efficiency of removal of metals under varying adsorption conditions of pH, metal concentration and contact time. Characterization studies of the biosorbent and SEM analysis were done. Kinetic modelling studies were tried using Lagergren pseudo-first-order and second-order models. Equilibrium studies were done using well-known Freundlich, Langmuir and D–R isotherm models. It was found that all isotherms are fitting well indicating the efficiency of coir pith as an adsorbent of heavy metals. The applicability of all the three isotherms to the sorption processes shows that both monolayer adsorption and heterogeneous energetic distribution of active sites on the surface of the adsorbent are possible. Due to the abundance and low cost of these materials, adsorption technologies developed can act as good sustainable options for the future in heavy metal removal from industrial effluents.     

萃取法分离回收不锈钢酸洗污泥硫酸浸出液中的重金属

采用非皂化P204和皂化P204萃取剂对不锈钢酸洗污泥的硫酸浸出液进行萃取。在浸出液pH为0.80、非皂化P204体积分数为25%、萃取剂与浸出液体积比为1∶2、萃取时间为5 min的条件下,Fe~(3+)萃取率达99.64%,Cr~(3+)和Ni~(2+)萃取率为3.98%和6.99%,一次萃余液pH为0.64。采用皂化P204对除Fe~(3+)后的一次萃余液进行萃取,在P204体积分数为25%、萃取剂与浸出液体积比为1∶2、萃取剂皂化率为60%、一次萃余液pH为1.50、萃取时间为5 min的条件下,Ni~(2+)萃取率为93.12%,Cr~(3+)萃取率为20.69%,二次萃余液pH为2.63。     

钙钛矿型催化剂催化湿式氧化处理煤气化废水纳滤浓缩液

采用溶胶-凝胶法制备了Mn掺杂钙钛矿型催化剂LaFexMn1-xO3,并以其为催化剂催化湿式双氧水氧化处理煤气化废水纳滤浓缩液。采用XRD,SEM,FTIR技术对催化剂进行了表征。表征结果显示：制备的催化剂均具有标准的钙钛矿型结构,其中,LaFe0.9Mn0.1O3的结构稳定,比表面积大。实验结果表明：制备的催化剂中LaFe0.9Mn0.1O3的催化活性最高,且稳定性好,连续使用5次后催化活性未见明显减弱;在H2O2投加量3.0 g/L、n（H2O2）∶n（LaFe0.9Mn0.1O3）=12∶1、反应温度160 ℃、反应压力1 MPa、浓缩液pH 3、反应时间60 min的最优条件下,COD、UV254和TOC的去除率分别达到80.9%、95.2%和68.0%,BOD5/COD由0.02提升至0.40,可生化性大幅提高。     

Comparative evaluation of sizing of metal hydride (MH) hydrogen storage tank filled with different alloys

This study presents a comparative analysis of sizing of metal hydride tank filled with different alloys. Alloys include solid solutions and intermetallic compounds of the generic families AB₅, AB₂, AB, A₂B. The effects of the different alloys on the sizing of metal hydride hydrogen storage tanks are complicated and depend on many factors. In this paper, a thermoeconomic optimization analysis with a simple algebraic formula was presented for the estimation of optimum metal hydride tank surface area for heat transfer enhancement. The optimum area of the metal hydride tank filled with commercially available different alloys (LaN₅, Ti_0,98Zr_0,02V_0,43Fe_0,09Cr_0,05Mn_1,5, TiFe, Mg₂NiH₄) was evaluated and compared by the developed method. The optimum net savings and the value of payback were determined for four alloys. It is found that mathematical model can be employed for the determination of optimum metal hydride tank design and increasing net savings according to alloy types. The optimum areas of the tanks filled with four alloys (LaN₅, Ti_0,98Zr_0,02V_0,43Fe_0,09Cr_0,05Mn_1,5, TiFe, Mg₂NiH₄) were calculated as 0.136, 0.130, 0.133, and 0.173 m², respectively. The optimum net savings for tanks filled with four alloys (LaN₅, Ti_0,98Zr_0,02V_0,43Fe_0,09Cr_0,05Mn_1,5, TiFe, Mg₂NiH₄) are about 461.0, 409.3, 419.6, and 979.6 $ and the values of payback are about 1.98, 2.1, 2.17, and 1.37 years, respectively. Excessive area of the metal hydride tank would not be as economical as the optimum tank area. Thermal management of metal hydride tank must be designed for optimum points calculated at which maximum savings occur.     

丝藻对含钼废水中MoO_4~(2-)的吸附特性及机制研究

研究了丝藻对含钼废水中MoO2-4的吸附作用。分别考察了初始pH、吸附时间、温度、投加量以及竞争离子等5个因素对吸附过程的影响,并应用吸附热力学和动力学方法对吸附机制进行了探讨。结果表明,丝藻在初始pH 1、吸附时间40min、投加量为1.0g以及30℃条件下,对含钼废水中MoO2-4的去除率达82%,平衡吸附量为0.657 0mg/g。PO3-4对MoO2-4的吸附具有较强的拮抗作用,平衡吸附量下降至0.380 0mg/g,SiO4-4对MoO2-4的拮抗作用相对较弱,而SO2-4对MoO2-4的吸附却有一定的协同作用。丝藻对MoO2-4的吸附等温数据更符合Langmuir吸附等温模型,准二级动力学方程拟合的吸附动力学过程相关性较高,20、25℃下的R2都在0.99以上。说明丝藻吸附MoO2-4属于化学吸附,受化学反应速率控制,且丝藻可以应用于含钼废水治理领域。     

火电灰渣场自然恢复下灰渣养分及重金属含量研究

对自然恢复下4类不同年代样地的灰渣养分含量及重金属含量进行研究,通过对比分析发现,有机质、全氮、全钾、全磷含量随着自然恢复时间的增加呈现递增的趋势,全磷含量在各恢复阶段与对照样地之间并不存在显著差异(P0.05)。pH随着恢复时间的增加呈现递减的趋势。对灰渣综合质量指数进行研究发现,自然恢复长期、中期、短期与自然恢复初期对比均有显著提高(P0.05),且随着自然恢复时间的增加灰渣综合质量指数逐渐提高。对灰渣场锌、铅、铜3种重金属研究后发现,在自然恢复下随着时间的增加,灰渣中重金属含量均呈现递减的趋势。     

建筑垃圾对雨水径流中Cu的吸附特性

以砖混建筑垃圾为研究对象,采用人工模拟雨水,通过静态和动态吸附实验研究了不同粒径粒级建筑垃圾对雨水径流中Cu的吸附效果。结果表明,准二级动力学模型比准一级动力学模型能更好地描述建筑垃圾对Cu的吸附过程;Freundlich等温模型能较好地拟合其等温吸附过程;不同粒径粒级建筑垃圾均对雨水径流中的Cu具有较好的净化效果,去除率均超过90%,粒径粒级越小,对Cu的净化效果越好,但其渗透性能越差;建筑垃圾的粒径粒级对Cu的吸附平衡时间、吸附速率和吸附量具有重要影响,粒径粒级2.36~4.75 mm的建筑垃圾对Cu的平衡吸附速率和平衡吸附量最大,分别为4.1μg/min和12.4μg/g。     

纳米铁氧化物吸附处理重金属废水的研究进展

概述了用于吸附重金属的主要纳米铁氧化物的种类及其吸附效果,介绍了常见的纳米铁氧化物制备方法及改性方法,讨论了影响纳米铁氧化物吸附重金属的主要因素,并对纳米铁氧化物在水环境保护领域中的研究方向提出了展望:如发展绿色、高效的纳米铁氧化物制备工艺,探讨纳米铁氧化物结构调控和表面功能化对其吸附性能的影响等。     

化学混凝法去除稠油废水中的硅

以新疆油田稠油废水为研究对象,采用化学混凝除硅方法对稠油废水进行处理。实验结果表明:采用锌复合混凝剂的混凝、软化及镁剂除硅相结合的方法具有较好的除硅效果。确定了最佳除硅配方:NaOH的加入量为500~600mg/L,除硅剂MgCl2.6H2O的加入量为700~800mg/L,锌复合混凝剂加入量为100~150mg/L,处理后废水中SiO2的质量浓度小于50mg/L,达到热采锅炉的用水标准。     

崇明东滩湿地沉积物重金属污染的磁诊断

对取自崇明东滩的高潮滩、中潮滩和低潮滩的沉积物柱样进行了磁学、粒度、重金属含量等指标的分析、比较与综合研究. 结果表明:在以粉砂为主的崇明东滩,通过污染负荷指数法进行评价,除低潮滩无污染外,中潮滩和高潮滩均有中度的重金属污染. 选取中度重金属污染的高潮滩沉积物柱样进行粒度、重金属含量以及磁性参数的相关性分析显示,χ_fd,χ_ARM/SIRM与重金属含量和粘土(粒径<4 μm)之间有较高的相关性,并以此建立了磁诊断线性回归模型;χ_fd和χ_ARM/SIRM可作为重金属含量的替代指标.