SGO改性复合纳滤膜的制备及分盐性能

近年来,水资源短缺,水源污染严重,国家对水处理末端的资源化利用提出了更高的要求,分盐过程也受到越来越多的关注.纳滤膜表面通常带有电荷,可以选择性地透过不同价态的离子.基于纳滤膜表面电荷特性不同,为很好地实现盐的分离,将制备的带有磺酸基团的氧化石墨烯引入到纳滤膜材料中,采用界面聚合法,制备了SGO改性复合纳滤膜. Zeta电位分析表明所制备的复合纳滤膜表面的电荷比不添加SGO的纳滤膜更负;红外光谱分析中酯基基团特征峰的出现表明磺酸基团参与了聚合反应; SEM结构表面,膜表面出现了明显的图灵结构,在0. 2 MPa压力下,纯水通量可达45. 85 L·(m~2·h)-1,对Na2SO4截留率为98. 23%,对Na Cl截留率为24. 93%,10 h运行可以很好地实现对SO_4~(2-)、Cl~-的有效分离,可实现盐的资源化回收.     

聚丙烯酰胺对聚合物驱含油污水中油珠沉降分离的影响

研究发现阴离子聚丙烯酰胺(HPAM)对聚合物驱含油污水处理有正反2方面影响.聚合物能增加污水粘度,降低油珠上浮速度,而且聚合物能增加油水界面水膜强度,延缓油珠聚并时间,这是聚合物对油珠沉降分离的不利影响;同时,聚丙烯酰胺具有絮凝性,能将水中油珠连接到一起,有利于油珠聚并.当聚丙烯酰胺相对分子质量为2.72×10⁶,浓度小于800mg/L时,絮凝作用大于粘度作用,有利于油珠的沉降分离.初始油珠粒径小是聚合物驱含油污水难处理的主要原因.横向流除油器可以加速油珠聚并,缩短沉降时间,适合处理聚合物驱含油污水.     

干法煤粉磁选脱硫的试验研究

本工作首次在国内完成了干法煤粉磁选脱硫的试验,探讨了脱硫机理,简述了磁法脱硫的工艺及高梯度磁分离器(HGMS)装置。试验结果表明:最佳梯度磁场强度为0.65—0.75T,最佳煤粉颗粒度在100目—120目,脱硫率最高达70％左右,费用估计为7.5元/t煤左右。     

淡水环境沉积物中微塑料的密度分离方法研究

微塑料污染已广泛覆盖了全球海洋和淡水环境的表层水体、深层水体以及沉积物,沉积物中的泥沙和其他杂质颗粒会严重影响对沉积物中微塑料的实验分析.因此,将微塑料从沉积物中分离出来至关重要,而目前我国微塑料分离方法暂无统一的系统程序和检测标准.该研究在岷江成都段选取4个采样点采集沉积物样品,通过对比研究基于密度分离法的3种分离方...     

不同操作条件对纳滤膜去除水中五价砷的研究

采用纳滤膜（NF90）过滤自配含砷水,研究在不同操作条件下纳滤膜对水中砷去除效果的影响。本实验探讨膜进水浓度、水的pH值、膜进水温度、操作压力、水中天然有机物浓度等对膜除砷效率的影响。结果表明：纳滤膜对水中五价砷（As（Ⅴ））的去除率很高,最高去除率能达到99%,在实验的前2.5个小时内,砷的去除率均在90%以上。但是,纳滤膜除砷效率随着时间变化,去除率会降低。不同的操作条件对纳滤膜除砷的影响很大,研究不同条件的影响对应用很有意义。     

钻井废液的固液分离工艺与设备

影响钻井废液固液分离的因素包括钻井废液的稀释比例、脱稳处理药剂的种类和加量、固液分离设备。文章介绍了钻井废液处理的基本流程,分析了钻井废液pH值对固液分离效果的影响,论述了卧式螺旋卸料沉降离心机的基本结构、设备参数和操作参数对固液分离效果的影响。     

水合物法的天然气提氦技术研究

氦气是发展国防军工和高科技产业不可或缺的战略性物资之一.由于氦气在自然界中的富集度很低,目前工业规模化提氦来源主要是含氦天然气.常用的提氦方法有吸附法、吸收法、低温冷凝法、膜分离法等,但它们都不能很好地解决提氦难度大、成本高、规模化工业应用水平较低等缺点.因此,引入水合分离技术,利用含氦天然气各组分生成水合物的条件差异在水合反应过程中对氦气提浓,同时辅以催化脱氢工艺,实现粗氦的精制.     

环境样品中汞形态分析技术的进展

汞的毒性、环境行为、生物有效性不仅跟其浓度有关,还决定于其化学形态,因此汞的形态分析在环境科学中具有重要意义。样品前处理几乎是汞形态分析研究中不可或缺的步骤,而色谱和光谱/质谱联用技术是目前普遍采用的分离检测方法。文章对近十年来这些方面的研究进展进行了综述,主要包括样品的前处理方法如酸/碱溶剂萃取、微波辅助萃取、固相萃取、固相微萃取、单滴微萃取、分散液液微萃取等,以及色谱(液相色谱、气相色谱)和毛细管电泳与光谱/质谱(紫外可见光谱、原子吸收光谱、原子荧光光谱、等离子体质谱等)的联用技术在汞化合物形态分析中的应用情况。最后提出今后应重点研究建立高效、简便的前处理方法,发展高分离度、高灵敏度、高速度的分离检测联用技术,以便更好地对汞的形态进行分析监测。     

膜电解法退镀废ABS电镀件及回收铜和镍

采用膜电解法对废丙烯腈-丁二烯-苯乙烯（ABS）电镀件进行退镀处理。以退镀废液作为阴极液和阳极液,在阳极室退镀ABS电镀件,在阴极室电解退镀废液,进行铜镍分离,回收铜粉和NiCl₂。实验结果表明：在阴极电流密度为500 A/m²、初始铜离子质量浓度为24.00 g/L的条件下电解160 min,阴极铜回收率可达97.65%,电流效率达86.60%,得到的铜粉纯度为97%~99%,处理1 L退镀废液可回收铜粉20.0 g,2 mol/L盐酸0.87 L,NiCl₂晶体43.8 g;在阳极电流密度为500 A/m²、液固比为6的条件下电解60 min, ABS电镀件的退镀率为77.22%。     

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.