Correlation between Calcium Carbonate Content and Emission Characteristics of Incense

Abstract

In Taiwan and China, calcium carbonate is commonly added as a filler during incense production to lower the cost. This study has found an unexpected benefit for this practice: it reduces particulate emission. Nine types of the popular incense on the local market were chosen for this study. The calcium content in raw material incense was analyzed by inductively coupled plasma atomic emission spectrometry, followed by X-ray diffraction (XRD) spectroscopy. The correlation between the calcium content and emission characteristics of incense was investigated. The calcium content varied from 1.8 to 60 mg/g (incense burned) among those nine different types of incense. Very little calcium (<1%) was found in natural wood or plants, which is mainly the raw material of incense. Instead, most calcium was artificially added in the form of CaCO₃ during manufacturing. The combustion characteristics, including burning rate, emission factors of particulate, ash, and solid-phase polycyclic aromatic hydrocarbons (SPAHs), varied significantly among the nine types of incense. Incense containing 2% calcium would emit 30% less S-PAHs, compared with those with little (<0.2%) calcium. More importantly, increasing the calcium content from 0.5 to 5% by adding CaCO₃ reduced the particulate emission from incense by ～50%.     

Particle size distribution and PAH concentrations of incense smoke in a combustion chamber

The particle size distribution and the concentrations of polycyclic aromatic hydrocarbons (PAHs) in incense smoke were studied using a custom-designed combustion chamber. Among the nine types of incense investigated, the particle and the total PAH emission factors varied significantly. The average mass median aerodynamic diameter (MMAD) of the smoke aerosol was 262+/-49nm, which positively correlated to particle emission factor (mg/stick, p<0.05). Coagulation was a major mechanism that dictates the MMAD of the smoke. The total toxic equivalency (the sum of the benzo[a]pyrene equivalent concentration) of the solid-phase PAHs (S-PAHs) was over 40 times higher than that of the corresponding gas-phase PAHs, indicating that the S-PAHs in incense smoke may pose potential health risk. Experiments show that each lowered percentage of total carbon content in the raw incense helped decrease the particle emission factor by 2.6mg/g-incense, and the reduction of S-PAH emission factor ranged from 8.7 to 26% when the carbon content was lowered from 45 to 40%.     

Study on fluoride emission from soils at high temperature related to brick-making process

Characteristics of fluoride emission from 12 soils at temperatures of 400-1,100 degrees C related to the brick-making process were studied. The results obtained in this study indicate that fluoride emission as gaseous HF and SiF4 was related to the firing temperature, soil total fluoride content, soil composition and calcium compounds added to soils. Soils began to release fluoride at temperatures between 500 and 700 degrees C. Marked increases of the average fluoride mission rate from 57.2% to 85.4% of soil total fluoride were noticed as the heating temperature was increased from 700 to 1,100 degrees C. It was found that the major proportion (over 50%) of the soil total fluoride was emitted from soils at approximate 800 degrees C. The amount of fluoride released into the atmosphere when heated depended on the total fluoride contents in the soils. Correlation analysis showed that the soil composition, such as cation exchange capacity, exchangeable calcium and CaCO3, had some influence on fluoride emission below 900 degrees C, but had no influence at temperatures above 900 degrees C. Addition of four calcium compounds (CaO, CaCO3, Ca(OH)2, and CaSO4) at 1.5% by weight raised the temperature at which fluoride began to be released to 700 degrees C. The greatest decrease in fluoride emission among the four calcium compound treatments was found with CaCO3.     

Generation rates and emission factors of particulate matter and particle-bound polycyclic aromatic hydrocarbons of incense sticks

The generation rates and emission factors of particulate matter and associated polycyclic aromatic hydrocarbons (PAHs) from incense burning were assessed in a laboratory setting. The differences among different segments of the same stick, among different sticks of the same kind of incense, and between two kinds of manually made Chih-Chen incense sticks (A and B) were evaluated. Joss sticks were burned inside a 44 cm long elutriator; personal environmental monitors fitted into the top of the elutriator were used to take PM2.5 and PM10 samples of incense smoke. Samples were analyzed for PAHs by gas chromatography-flame ionization Detector. It was found that particle and associated PAHs were generated approximately at 561 microg/min (geometric standard deviation (GSD) = 1.1) and 0.56 microg/min (GSD = 1.1) from Incense A, and at 661 microg/min (GSD = 1.7) and 0.46 microg/min (GSD = 1.3) from Incense B, respectively. One gram of Incense A emitted about 19.8 mg (GSD = 1.1) particulate matter and 17.1 microg (GSD = 1.2) particulate-phase PAHs, while one gram of Incense B produced around 43.6 mg (GSD = 1.1) of particles and 25.2 microg (GSD = 1.2) of particle-bound PAHs. There were significant differences in emissions between Incenses A and B, although they belong to the same class of incense. A 10-20% variability in emissions was observed in the main part of the manually produced stick, and a larger variation was found at both tips of the combustible part.     

Characterization of particulate matter concentrations during controlled indoor activities

Indoor sources have been identified as a major contributor to the increase of particle concentration in indoor environments. The work presented here is a study of the characteristics of particulate matter number size distribution and mass concentration under controlled indoor activities in a laboratory room. The objective is to characterize particulate matter concentrations indoors resulted under the influence of specific sources. Measurements were performed in an empty laboratory (period September–October 2006) using a GRIMM SMPS+C system (particle size range between 11.1 and 1083.3 nm), a DustTrak Aerosol Monitor (TSI) and a P-Trak Ultrafine Particle Counter (TSI). The studied indoor activities included candle burning, hot plate heating, water boiling, onion frying, vacuuming, hair drying, hair spraying, smoking and burning of incense stick. The AMANpsd computer algorithm was used to evaluate the modal structure of measured particle number size distribution data. Furthermore, the change of the particle number size distribution shape under the influence of different emission sources was studied versus time. Finally the particle emission rates were computed. High particle number concentrations were observed during smoking, onion frying, candle burning and incense stick burning. The highest particle mass concentrations were measured during smoking and hair spraying. The shift of the particle size distribution to larger diameters suggests the presence of strong coagulation effect during candle burning, incense stick burning, smoking and onion frying. The size distribution was mainly bimodal during onion frying and candle burning, whereas the size distribution remained unimodal during incense stick burning and smoking experiments.     

Anhydrosugar and sugar alcohol organic markers associated with carboxylic acids in particulate matter from incense burning

Aerosol from the burning two types of sandalwood-based incense, Hsing Shan and Lao Shan, was analyzed to characterize the chemical profile of total particulate matter emitted. The total particulate matter (PM) mass emission factors were 46.3 ± 2.68 mg g^?1 of Hsing Shan incense and 43.7 ± 1.08 mg g^?1 of Lao Shan incense. Chemical analysis of emissions from the two types of incense revealed that of the 25 components in four groups characterized, anhydrosugars formed the major group, at 46.7–52.2% w/w of the identified particulate and 1078.3–1169.8 μg g^?1 of incense, followed by inorganic salts at 30.4–31.8% w/w of identified particulate and 681.6–734.0 μg g^?1 of incense, carboxylic acids at 12.0–17.1% w/w of the identified particulate and 268.6–392.8 μg g^?1 of incense, and sugar alcohols at 4.44–5.38% w/w of the identified particulate and 102.3–120.6 μg g^?1 of incense. More anhydrosugars and sugar alcohols were emitted from Lao Shan incense than from Hsing Shan incense whereas more carboxylic acids and organic salts were emitted from Hsing Shan than from Lao Shan. These differences were due to structural and functional differences in the young sandalwood used to make Hsing Shan and the aged sandalwood used to make Lao Shan. The anhydrosugar levoglucosan, used as a marker of biomass burning, was always the most abundant species in emitted PM for both incenses (Lao Shan 21.7 mg g^?1 of PM and Hsing Shan 18.7 mg g^?1). K⁺ and Cl^? were the second most abundant components (K⁺ and Cl^? were summed), accounting for 10.6 mg g^?1 of Hsing Shan PM and 9.85 mg g^?1 of Lao Shan PM. The most abundant carboxylic acids in the emissions were formic, acetic, succinic, glutaric and phthalic acid. The latter is a fragrance ingredient and a potential health hazard and was twice as prevalent in Lao Shan emissions. Xylitol was the most prevalent of the sugar alcohols at 35.7–36.6% w/w of total identified sugar alcohols. These abundant species are potential markers for incense burning. K⁺, levoglucosan, mannosan and xylitol are already reported in discriminator ratios for wood burning and it is proposed here that these can and should also apply to incense burning. The calculated discriminator ratios for two types of incense burning reported here are 0.229–0.288 for K/Levo, 12.5–13.5 for Levo/Manno, and 21.5–23.7 for the novel discriminator ratio Levo/Xylitol.     

Fugitive dust emission source profiles and assessment of selected control strategies for particulate matter at gravel processing sites in Taiwan

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM10), fine suspended particulate (PM2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (< 100 microm) concentrations at the boundary of gravel sites ranged from 280 to 1290 microg/m3, which clearly exceeds the Taiwan hourly air quality standard of 500 microg/m3. Moreover, PM10 concentrations, ranging from 135 to 550 microg/m3, were also above the daily air quality standard of 125 microg/m3 and approximately 1.2 and 1.5 times the PM2.5 concentrations, ranging from 105 to 470 microg/m3. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 microm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

Fine (PM2.5), coarse (PM2.5-10), and metallic elements of suspended particulates for incense burning at Tzu Yun Yen temple in central Taiwan

Ambient suspended particulate concentrations were measured at Tzu Yun Yen temple (120 degrees, 34('), 10(") E; 24 degrees, 16('), 12(") N) in this study. This is representative of incense burning and semi-open sampling sites. The Universal-sampler collected fine and coarse particle material was used to measure suspended particulate concentrations, and sampling periods were from 16/08/2001 to 2/1/2002 at Tzu Yun Yen temple. In addition, metallic element concentrations, compositions of PM(2.5) and PM(2.5-10) for incense burning at Tzu Yun Yen temple were also analyzed in this study. The PM(2.5)/PM(10) ratios ranged between 31% and 87% and averaged 70+/-11% during incense the burning period, respectively. The median metallic element concentration order for these elements is Fe>Zn>Cr>Cd>Pb>Mn>Ni>Cu in fine particles (PM(2.5)) at the Tzu Yun Yen temple sampling site. The median metallic element concentration order for these elements is Fe>Zn>Cr>Pb>Cd>Ni>Mn>Cu in coarse particle (PM(2.5-10)) at the Tzu Yun Yen temple sampling site. Fine particulates (PM(2.5)) are the main portion of PM(10) at Tzu Yun Yen temple in this study. From the point of view of PM(10), these data reflect that the elements Fe, Zn, and Cr were the major elements distributed at Tzu Yun Yen temple in this study.     

Partitioning and photodegradation of ciprofloxacin in aqueous systems in the presence of organic matter

Ciprofloxacin is an extensively used antibiotic that has been reported to occur in surface water. Previous studies have indicated that ciprofloxacin photodegrades and sorbs to particulate organic material within aquatic systems. The first objective of the current study was to evaluate the influence of organic material on photodegradation rates of ciprofloxacin. Using a bench top experimental design, ciprofloxacin was added to experimental chambers that contained only water or water and fine particulate organic matter (FPOM) followed by exposure to ultraviolet light. Sorption to FPOM was rapid, reducing the amount of ciprofloxacin that was available for photodegradation. Thus, the presence of FPOM initially decreased the ciprofloxacin concentration in the aqueous compartment. However by the end of the 16 h test, 42% of the ciprofloxacin was recovered from the test system with FPOM present, while only 2% of the ciprofloxacin was recovered in systems that did not contain FPOM. The second objective of this study was to compare the sorption coefficients for ciprofloxacin between two types of organic material: FPOM, classified as amphipod processed leaves, and coarse particulate organic matter (CPOM), represented by intact leaf disks. Sorption to FPOM (log Kd of 4.54+/-0.09 l kg(-1)) was 1.6 orders of magnitude greater than sorption to CPOM (log Kd of 2.92+/-0.10 l kg(-1)) potentially resulting in differential toxicity among similar organisms that occupy these different niches and leading to different estimates of environmental fate and effects.     

Potential effects of particulate matter from combustion during services on human health and on works of art in medieval churches in Cyprus

Indoor and outdoor particulate matter (PM_0.3-10) number concentrations were established in two medieval churches in Cyprus. In both churches incense was burnt occasionally during Mass. The highest indoor PM_0.5-1 concentrations compared with outdoors (10.7 times higher) were observed in the church that burning of candles indoors was allowed. Peak indoor black carbon concentration was 6.8 μg m⁻³ in the instances that incense was burning and 13.4 μg m⁻³ in the instances that the candles were burning (outdoor levels ranged between 0.6 and 1.3 μg m⁻³). From the water soluble inorganic components determined in PM₁₀, calcium prevailed in all samples indoors or outdoors, whilst high potassium concentration indoors were a clear marker of combustion. Indoor sources of PM were clearly identified and their emission strengths were estimated via modeling of the results. Indoor estimated PM_0.3-10 mass concentrations exceeded air quality standards for human health protection and for the preservation of works of art.     

废旧电路板与碳酸钙共热解脱卤的研究

采用热重分析仪和石英管式炉热解反应器，分别对以酚醛树脂为基板的废旧电路板和混合碳酸钙后的废旧电路板进行热解实验研究，着重考察了添加碳酸钙后的酚醛树脂基板废旧电路板热解特性及添加量不同对卤素脱除效果的影响。实验结果表明，碳酸钙的加入对废旧电路板的降解行为和热解油的基本组成没有明显的影响，但热解油的各组分含量有所差异；随着热解温度的提高或者CaCO₃含量的增多，卤素可以更多地由有机卤向无机卤转变并束缚在固体残渣中，由此得到较好的脱卤效果。当60%PR-WPCBs与40%CaCO₃共热解，热解油中的溴化物也减少了7.6% 。在600℃等量CaCO₃与PR-WPCBs共热解时生成75.6%无机卤，其中70.62%束缚于固体残渣中，可见达到较好的脱卤效果。     

Impact of free calcium oxide content of fly ash on dust and sulfur dioxide emissions in a lignite-fired power plant

Emitted pollutants from the Agios Dimitrios lignite-fired power plant in northern Greece show a very strong linear correlation with the free calcium oxide content of the lignite ash. Dust (fly ash) emissions are positively correlated to free calcium oxide content, whereas sulfur dioxide (SO2) emissions are negatively correlated. As a result, at present, the Agios Dimitrios Power Plant operates very strictly within the legislative limits on atmospheric particulate emission. In the present study, the factors to be considered in assessing the impact of lignite combustion on the environment are presented and evaluated statistically. The ash appears to have a remarkable SO2 natural dry scrubbing capability when the free calcium oxide content ranges between 4 and 7%. Precipitator operating problems attributable to high ash resistivity can be overcome by injecting sulfur trioxide to reduce the ash resistivity, with, of course, a probable increase in operating costs.     

晶种及晶型助长剂对磷石膏制备硫酸钙晶须的影响

实验以磷石膏为原料,硫酸钙为晶种,镁盐为晶型助长剂,采用水热法制备硫酸钙晶须。实验详细考察了晶种的用量,镁盐晶型助长剂种类及用量,晶种、晶型助长剂、结晶稳定剂三者的协同效应等对硫酸钙晶须形态的影响。用偏光显微镜和扫描电镜(SEM)及X射线衍射分析了硫酸钙晶须的形貌和相组成。结果表明在硫酸镁作为晶型助长剂,晶种∶晶型助长剂∶结晶稳定剂的用量为1∶3∶4时制备出的硫酸钙晶须产品优,其光滑,反应完全,长度最长可达150μm左右,直径细度可细达0.5μm。     

再生水灌溉对土壤中重金属形态及分布的影响

通过土柱模拟实验,分析了再生水灌溉对土壤pH、电导率(EC)、有机质、CaCO3水平及4种重金属(Zn、Cd、Cu、As)的形态和分布的影响,探讨了再生水灌溉对土壤中重金属形态稳定性的影响.结果表明,和地下水灌溉(清灌)相比,再生水灌溉(污灌)使表层土中有机质质量分数由0.06％增加到0.32％,pH降低了0.4个单位...     

Fugitive Dust Emission Source Profiles and Assessment of Selected Control Strategies for Particulate Matter at Gravel Processing Sites in Taiwan

Abstract

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM₁₀), fine suspended particulate (PM_2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (<100 µm) concentrations at the boundary of gravel sites ranged from 280 to 1290 µg/m³, which clearly exceeds the Taiwan hourly air quality standard of 500 µg/m³. Moreover, PM₁₀ concentrations, ranging from 135 to 550 µg/m³, were also above the daily air quality standard of 125 µg/m³ and approximately 1.2 and 1.5 times the PM_2.5 concentrations, ranging from 105 to 470 µg/m³. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 µm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

Sources of fine particulate species in ambient air over lake Champlain Basin, VT

This study is a part of an ongoing investigation of the types and locations of emission sources that contribute fine particulate air contaminants to Underhill, VT. The air quality monitoring data used for this study are from the Interagency Monitoring of Protected Visual Environments network for the period of 2001-2003 for the Underhill site. The main source-receptor modeling techniques used are the positive matrix factorization (PMF) and potential source contribution function (PSCF). This new study is intended as a comparison to a previous study of the 1988-1995 Underhill data that successfully revealed a total of 11 types of emission sources with significant contributions to this rural site. This new study has identified a total of nine sources: nitrate-rich secondary aerosol, wood smoke, East Coast oil combustion, automobile emission, metal working, soil/dust, sulfur-rich aerosol type I, sulfur-rich aerosol type II, and sea salt/road salt. Furthermore, the mass contributions from the PMF identified sources that correspond with sampling days with either good or poor visibility were analyzed to seek possible correlations. It has been shown that sulfur-rich aerosol type I, nitrate aerosol, and automobile emission are the most important contributors to visibility degradation. Soil/dust and sea salt/road salt also have an added effect.     

Characterization of incense smoke by solid phase microextraction—Comprehensive two-dimensional gas chromatography (GC×GC)

Comprehensive two-dimensional gas chromatography in tandem with flame ionization detection (GC×GC-FID) was used for the qualitative fingerprint characterisation of four different types of powdered incense headspace (H/S), and incense smoke. Volatile organic compounds (VOCs) in the incense powder and smoke were extracted by using solid phase microextraction (SPME) with a polydimethylsiloxane/divinylbenzene (PDMS/DVB) 65 μm fiber. Low-polarity/polar, and polar/non-polar phase combinations were tested to contrast the GC×GC separation of components in these two column sets.A total of 324 compounds were tentatively identified, with more than 100 compounds in incense powders and more than 200 compounds in the incense smoke, by using GC coupled to quadrupole mass spectrometric detection. Identification required at least 90% match with the NIST library; otherwise they were considered as unidentified. The smoke stream comprised compounds originating from the incense powder, and combustion products such as PAH, N-heterocyclics, and furans. However, GC×GC was able to separate many more volatile compounds (possibly hundreds more) present in the complex smoke samples, many of which cannot be separated by conventional 1D-GC; this is a direct consequence of the high-resolution power of GC×GC. GC×GC fingerprint comparison of powder H/S with smoke allows facile subtraction of the former from the latter to assist identification of compounds generated from burning incense.     

Impact of Free Calcium Oxide Content of Fly Ash on Dust and Sulfur Dioxide Emissions in a Lignite-Fired Power Plant

Abstract

Emitted pollutants from the Agios Dimitrios lignite-fired power plant in northern Greece show a very strong linear correlation with the free calcium oxide content of the lignite ash. Dust (fly ash) emissions are positively correlated to free calcium oxide content, whereas sulfur dioxide (SO₂) emissions are negatively correlated. As a result, at present, the Agios Dimitrios Power Plant operates very strictly within the legislative limits on atmospheric particulate emission. In the present study, the factors to be considered in assessing the impact of lignite combustion on the environment are presented and evaluated statistically. The ash appears to have a remarkable SO₂ natural dry scrubbing capability when the free calcium oxide content ranges between 4 and 7%. Precipitator operating problems attributable to high ash resistivity can be overcome by injecting sulfur trioxide to reduce the ash resistivity, with, of course, a probable increase in operating costs.     

Sources of Fine Particulate Species in Ambient Air over Lake Champlain Basin,VT

Abstract

This study is a part of an ongoing investigation of the types and locations of emission sources that contribute fine particulate air contaminants to Underhill, VT. The air quality monitoring data used for this study are from the Interagency Monitoring of Protected Visual Environments network for the period of 2001–2003 for the Underhill site. The main source-receptor modeling techniques used are the positive matrix factorization (PMF) and potential source contribution function (PSCF). This new study is intended as a comparison to a previous study of the 1988–1995 Underhill data that successfully revealed a total of 11 types of emission sources with significant contributions to this rural site. This new study has identified a total of nine sources: nitrate-rich secondary aerosol, wood smoke, East Coast oil combustion, automobile emission, metal working, soil/dust, sulfur-rich aerosol type I, sulfur-rich aerosol type II, and sea salt/road salt. Furthermore, the mass contributions from the PMF identified sources that correspond with sampling days with either good or poor visibility were analyzed to seek possible correlations. It has been shown that sulfur-rich aerosol type I, nitrate aerosol, and automobile emission are the most important contributors to visibility degradation. Soil/dust and sea salt/road salt also have an added effect.     

Determining the effectiveness of conventional and alternative coagulants through effective characterization schemes

Polymeric forms of metal coagulants in water treatment have become increasingly used due to their wider availability and reduction in cost. These specialized coagulant forms and products are claimed by manufacturers to be superior to conventional coagulants in particulate and/or organic removal with inherent advantages of lower alkalinity consumption and lesser sludge production. However, due to their proprietary nature, little is known about their chemical composition. To determine and understand the effectiveness of these alternative coagulants, a comprehensive study was undertaken to characterize metal coagulants, and to comparatively evaluate them on a well-characterized source water. The objective of this study was to provide a scheme for utilities that could be employed as a screening process and a method of selecting an appropriate coagulant based on raw water characteristics and insight into the coagulatability of the source water. Characterizations of coagulants included: (i) active metal content, (ii) anion content, (iii) acidity, (iv) alkalinity consumption, (v) charge reversal by colloidal titration, and (vi) molecular weight determination. A total of five poly-aluminum chlorides (PACl), along with a conventional coagulant (aluminum sulfate or alum) were evaluated. Results show that through the characterization scheme, an effective coagulant (conventional versus alternative) and coagulant type (among various PACl) can be chosen before undertaking time-consuming bench or pilot-scale evaluation.