光催化氧化深度处理电镀有机废水的工程化实验

采用光催化氧化联用技术对电镀有机废水进行深度处理工程化实验。探讨了uV、uV＋H2O3、uV＋H2O2＋TiO2、uV＋H2O2＋FeSO4、uV＋H2O2＋FeSO4＋TiO2、uV＋O3＋TiO2和uV＋03＋TiO2＋H2O2等体系对废水有机污染物去除率的影响。结果表明，相较于其他反应体系，uV＋O3＋TiO2＋H2O2体系具有更好的氧化效果，经碳滤处理后去除率达到90％以上，最终出水水质满足GB18918-20O2-级标准（A标准）的要求。实际运行项目偿还期5．33年，NPV〉0，内部收益率大于基准值10％。研究表明，uV＋O3＋TiO2＋H2O，体系能降低加药量，工作量及运行成本。可为电镀企业实际废水处理提供现实依据，为优化电镀废水的处理工艺提供参考。     

Elucidation of the behavior of tannery wastewater under advanced oxidation conditions

Diverse advanced oxidation process (AOP) techniques applying UV, TiO2/UV, O3 and O3/UV were used to degrade pollutants contained in tannery wastewater. The total mineralization of these pollutants is desirable, but it is quite energy consuming and sometimes impossible. Therefore the objective was to achieve an enhancement of biodegradability, preferentially with a decrease in toxicity in parallel. This work demonstrates that the dominant pollutants were chemically degraded by oxidation, while changes in carbon content were only marginal. These results were obtained monitoring the total organic carbon content (TOC), chemical and biochemical oxygen demand (COD and BOD), and substance-specific pollutant content by application of gas chromatography/mass spectrometry (GC-MS) and liquid chromatography/mass spectrometry (LC-MS). Daphnia magna toxicity testing performed in parallel proved a decrease in toxicity after AOP treatment of the tannery wastewater.     

Comparison of various advanced oxidation processes and chemical treatment methods for COD and color removal from a polyester and acetate fiber dyeing effluent

In this paper, a comparison of various advanced oxidation processes (O3, O3/UV, H2O2/UV, O3/H2O2/UV, Fe2+/H2O2) and chemical treatment methods using Al2(SO4)3.18H2O, FeCl3 and FeSO4 for the chemical oxygen demand (COD) and color removal from a polyester and acetate fiber dyeing effluent is undertaken. Advanced oxidation processes (AOPs) showed a superior performance compared to conventional chemical treatment, which maximum achievable color and COD removal for the textile effluent used in this study was 50% and 60%, respectively. Although O3/H2O2/UV combination among other AOPs methods studied in this paper was found to give the best result (99% removal for COD and 96% removal for color), use of Fe2+/H2O2 seems to show a satisfactory COD and color removal performance and to be economically more viable choice for the acetate and polyester fiber dyeing effluent on the basis of 90% removal.     

Treatment of landfill leachate by ozone-based advanced oxidation processes

In this study, laboratory experiments are conducted to compare the efficacy using several ozone-based advanced oxidation processes (AOPs), such as O3, O3/H2O2, and O3/UV, to treat landfill leachate. Raw leachate was initially coagulated by ferric chloride (FeCl3) at the experimental-determined optimal dosage of 900 mgl(-1), and the ozone-based AOPs were subsequently applied. Results indicate that all AOPs would result in a significant increase on the ratio of BOD5/COD from 0.06 to 0.5 at the applied ozone dosage of 1.2 gl(-1). The increase on biodegradability for ozonated leachate indicates that these AOPs would be beneficial to the subsequent biological treatment process. To better explain the alteration of high organic molecules after oxidation, ultrafiltration was used to separate the leachate by several molecular weight cutoffs (MWCO). The COD distribution for coagulated leachate is 34% for MWCO>10 kDa, 7% for MWCO between 5 and 10 kDa, 22% for MWCO between 1 and 5 kDa, and 37% for MWCO<1 kDa. Following ozonation or AOPs, the predominant distribution of COD would be obviously shifted to the MWCO less than 1000 gmol(-1) (72-85%) over the other MWCO ranges. In addition, Gel Permeation Chromatograph (GPC) analysis has showed a substantial agreement on the cleavage of larger organic compounds into smaller ones. O3/UV was found to be the most effective approach among these ozone-based AOPs to enhancing the biodegradability and eliminating the color of leachate.     

紫外光助O3、H2O2氧化降解炼油废碱水的可行性实验

炼油高浓度有机废碱水是石化行业中很难降解的废水.本实验用光化学氧化技术对其进行了降解研究,比较了紫外光/空气、紫外光/O3、紫外光/空气/H2O2系统的处理效果.结果表明,光化学氧化技术降解此废水是可行的,紫外光可使废水中COD、油、酚的降解率明显提高.当废水中O3的投加量每小时为22 mg/L,或H2O2投加量为1%/L时,UV/O3法与UV/空气/H2O2法的降解效果相近.同时,通过控制O3浓度或H2O2的投加量等条件,可使废水中COD、油、酚和硫化物降解到地方污染物二级排放标准.     

Photocatalytic oxidation of pesticide rinsate

Pesticide rinsate has been considered as one of the major threats for the environment. In this study, photocatalysts such as TiO2 and O3 were used to promote the efficiency of direct UV photolysis to prevent such wastewater pollution. Carbofuran (a carbamate pesticide) and mevinphos (an organophosphate pesticide) with a concentration of 100 mg/L were selected as the test pesticide rinsates. Parent pesticide compound, COD, and microtoxicity analysis were employed to investigate the effect of photocatalyst on the degradation efficiency of pesticide in rinsate. It was found that the photocatalytic oxidation process (UV/O3, UV/TiO2) showed much higher COD removal and microtoxicity reduction efficiency for pesticide rinsate than did direct UV photolysis under the imposed conditions, suggesting that photocatalytic oxidation processes such as UV/O3 and UV/TiO2 could be a better alternative to treat pesticide rinsate. In addition, it was noted that increasing the initial pH of mevinphos rinsate to a basic level was required to reach higher COD removal efficiency and positive microtoxicity reduction efficiency while it was not necessary for the treatment of carbofuran rinsate.     

Photocatalytic degradation of cellulose bleaching effluent by supported TiO2 and ZnO

A cellulose bleaching effluent (E1) was degraded in batch conditions by photocatalysis using TiO2 and ZnO supported on glass Raschig rings. The effluent was completely decolourised and the total phenol content was reduced by 85% after 120 min treatment with both catalysts. Partial mineralization of the organic matter was confirmed by total organic carbon (TOC) reduction, approximately 50%. The residual organic matter shows a low acute toxicity as compared to the initial values and AOX values are strongly reduced after the photocatalytic oxidation. Molecular mass distribution showed that high molecular mass compounds were almost completely degraded.     

偶氮二异庚腈生产废水处理试验和工程调试

偶氮二异庚腈的生产过程中产生大量的废水,其有机物和氨氮含量高,生化性差.为解决其处理达标问题,采用氨氮吹脱-上流式厌氧污泥床(UASB)-A/O- NaOCl强氧化-接触氧化的组合工艺对其进行了试验研究.结果表明,该工艺对COD、氨氮的去除率分别达到99％、98％以上.并在此试验研究的基础上,投资建设了一个污水处理站,采用氨氮吹脱-UASB-A/O-二级好氧-NaOCl强氧化-接触氧化-气浮池的组合工艺,经过一年多的运行,出水水质稳定,对COD、氨氮的去除率分别为99％、98％以上,出水水质达到《污水综合排放标准》(GB 8978-1996)的一级标准.     

Treatment of oily port wastewater effluents using the ultraviolet/hydrogen peroxide photodecomposition system.

This paper presents the nonselective degradation of mechanically pretreated oily wastewater by hydrogen peroxide (H2O2) in the presence and absence of UV irradiation. The effect of chemical oxidation on wastewater biodegradability was also examined. The exclusive use of H2O2 photolyzed by daylight results in quite efficient degradation rates for the low peroxide concentrations used. Higher hydrogen peroxide concentrations inhibit degradation of organic contaminants in the wastewater. The degradation rates of all contaminants are relatively high with an advanced oxidation system (UV/H2O2), but degradation efficiencies are not distinguishably different when 20 or 45 minutes of UV irradiation is used. The excess of H2O2 used in the process can inhibit phenolic degradation and may lead to the formation of a new phenolic fraction. The biodegradability of port wastewater did not increase significantly following the application of the advanced oxidation process.     

Synergy of ozonation and photocatalysis to mineralize low concentration 2,4-dichlorophenoxyacetic acid in aqueous solution

Concentration of 2,4-dichlorophenoxyacetic acid (2,4-D) may affect its degradation kinetics in advanced oxidation systems, and combinations of two or more systems can be more effective for its mineralization at low concentration levels. Degradations and mineralizations of 0.045mM 2,4-D using O(3), O(3)/UV, UV/TiO(2) and O(3)/UV/TiO(2) systems were compared, and influence of reaction temperature on the mineralization in O(3)/UV/TiO(2) system was investigated. 2,4-D degradations by O(3), O(3)/UV and UV/TiO(2) systems were similar to the results of earlier investigations with higher 2,4-D concentrations. The degradations and total organic carbon (TOC) removals in the four systems were well described by the first-order reaction kinetics. The degradation and removal were greatly enhanced in O(3)/UV/TiO(2) system, and further enhancements were observed with larger O(3) supplies. The enhancements were attributed to hydroxyl radical (()OH) generation from more than one reaction pathway. The degradation and removal in O(3)/UV/TiO(2) system were very efficient with reaction temperature fixed at 20 degrees C. It was suspected that reaction temperature might have influenced ()OH generation in the system, which needs further attention.     

臭氧与TiO2/UV协同降解对氯苯酚

利用O3／UV、TiO2／UV和O3／TiO2／UV降解对氯苯酚表明，臭氧与TiO2／UV具有明显的协同作用，如在本实验条件下降解5min后，上述3者对对氯苯酚的去除率分别为55％、10％和77%。O3／TiO2／UV协同作用的本质是由于臭氧能带走二氧化钛光致电子空穴对中的电子，从而产生了更多的羟基自由基，加速了有机物的降解。     

Fenton-水解酸化-接触氧化处理模拟磷霉素钠制药废水

对模拟磷霉素钠制药废水进行Fenton-水解酸化-接触氧化小试处理实验,考察了COD、有机磷的去除效果,并对处理前后的废水进行了GC-MS分析。结果显示,增加了Fenton预处理后磷霉素钠制药废水的COD和有机磷分别降低到100和2 mg/L,去除率均可达87%以上,出水COD满足化学制药行业污染物排放标准(GB 21904-2008);Fenton过程对制药厂废水中的复杂有机物去除效果明显,GC-MS结果表明,出水中基本检测不到复杂有机物。与制药厂采用的水解酸化-接触氧化处理效果相比,增加Fenton预处理可以提高废水的可生化性和系统的处理效率。     

Fenton组合工艺处理焦化厂生化出水的应用研究

比较了Fenton氧化、Fenton氧化+活性炭及Fenton氧化+生物活性炭工艺对焦化厂生化出水的处理效果.结果表明,Fe2+、H2O2的投加量分别为56、27.2 mg/L时,Fenton氧化工艺对水样的UV254、颜色度(VIS380)、COD和总氰均有较好的去除效果;Fenton氧化+活性炭工艺在有效去除UV254、VIS380、COD和总氰的同时,能强化活性炭的吸附效果,并能显著提高水样的生化性能;Fenton氧化+生物活性炭工艺能有效去除UVM254,VIS380、COD与总氰,使出水达到<污水综合排放标准>(GB 8978-1996)一级标准.     

TiO2/GeO2复合膜光催化氧化降解农药废水的研究

提出了一种新的TiO₂/GeO₂复合膜圆形光催化氧化反应器，研究了该反应器对经物化处理后的农药废水进行降解的过程。研究表明，光催化氧化的最佳条件是锌片镀TiO₂/GeO₂复合膜、pH=6.7、过氧化氢（H₂O₂）浓度为400 mg/L。并对其他氧化剂对该过程的影响进行了探讨。有机废水通过该反应器处理后，其COD值降为57mg/L。能使有机污染物全部降解为小分子无机物，废水达到国家一级排放标准。     

Slurry-phase ozonation for remediation of sediments contaminated by polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons (PAHs) are a group of toxic, persistent, bioaccumulating organic compounds containing two or more fused aromatic rings. They are listed by the U.S. Environmental Protection Agency as priority pollutants because of their carcinogenicity and toxicity. Employing ozonation as a remediation technique, this work investigated the treatability of a sediment sample from a freshwater boat slip subjected to coal tar contamination over a long period. The contaminated sediment sample contained high levels of PAHs in the forms of naphthalene, phenanthrene, pyrene, and benzo[a]pyrene, among other byproducts present in the humic and solid phases of the sediment. The objectives of this work were to examine (1) the degradation of PAHs in the contaminated sediment as treated by ozonation in the slurry form, (2) the effects of ozonation upon the soil matrix and the biodegradability of the resultant PAH intermediates, and (3) the feasibility of a combined technique using O3 as a pretreatment followed by biological degradation. The sediment was made into 3% w/w soil slurries and ozonated in a 1.7-L semi-batch, well-stirred reactor equipped with pH control and a cold trap for the gaseous effluent. Samples were collected after different ozonation durations and tested for biochemical oxygen demand (BOD), chemical oxygen demand (COD), UV absorbance, and toxicity, along with quantitative and qualitative determinations of the parent and daughter intermediates using gas chromatography/flame ionization detection (GC/FID), GC/mass spectrometry (MS), and ion chromatography (IC) techniques. The GC/MS technique identified 16 compounds associated with the humic and solid phases of the sediment. Intermediates identified at different ozonation times suggested that the degradation of PAHs was initiated by an O3 attack resulting in ring cleavage, followed by the intermediates' oxidation reactions with O3 and the concomitant OH radical toward their mineralization. Results suggested that ozonation for 2 hr removed 50-100% of various PAHs in the solid and liquid phases (as well as the aqueous and gaseous media resulting from the treatment process) of the sediment sample and that organic and inorganic constituents of the sediment were also altered by ozonation. Measurements and comparisons of BOD, COD, UV absorbance, and toxicity of the samples further suggested that ozonation improved the bioavailability and biodegradability of the contaminants, despite the increased toxicity of the treatment effluent. An integrated chemical-biological system appeared to be feasible for treating recalcitrant compounds.     

pH indications in aqueous organic photodecompositions with carbonyl and hydroxyl groups

A pH variation pattern during organic compound (ethylene glycol, phenol, and glucose) decomposition under UV/H2O2 of different schemes was observed. This method was successfully applied to reflect the organic carbon oxidation progress, especially the rapid chemical oxygen demand (COD) decrease timing in the later mineralization stage. The results were demonstrated in a sequential feed-batch advanced oxidation reactor, showing that pH can be used as an alternative indicator to provide complete oxidation and cycle time information.     

Treatment of landfill leachate by electrochemical oxidation and anaerobic process.

The removal performance of typical refractory organic compounds in landfill leachate was investigated during the electrochemical (EC) oxidation and anaerobic process combined treatment system in this paper. The results indicated that the treatment of landfill leachate by the combined system was highly effective. The toxicity of leachate was notably decreased after the electrochemical oxidation process and the biodegradability was improved. The concentration of the organic acid with low molecular weight in the leachate increased from 28% to 90% based on the biodegradability assays after the EC oxidation process. The anaerobic digestion could further remove the residual organic compounds. At a hydraulic retention time (HRT) of 16 hours and an organic loading rate (OLR) of 8 kg COD/m3 d, the concentration of COD, SS, ALK, VA, N-TKN, N-NH4+ and P-PO4(3)- [corrected] in UASB effluent were 532, 12, 6744, 400, 540, 455 and 11.6 mg/L, respectively, with approximately 90% removal efficiency of COD. The organic compounds in the landfill leachate revealed different degradation characteristics in the combined system. p-chloroaniline, bisphenol A, 6-methyl-2-phenyl-quinoline, dimethylnaphthaline and N'-(2-methyl-4-chlorophenyl)-N-cyclohexyformamidine, classified into the first group in this paper, were completely removed by the EC oxidation and did not reappear in the effluent of the UASB reactor. Phenylacetic acid, 3-methyl-indole and N-cyclohexyl-acetamide, called the second group, were completely removed, but reappeared in the UASB reactor. 4-methyl-phenol, 3,4-dihydroisoquinoline, 2(3H)-benzothiazolone, exo-2-hydroxycineole and benzothiazole, the third group, were degraded little in the EC oxidation process, but extensively removed by the anaerobic process. Benzoic acid, benzenepropanoic acid and 2-cyano-3,5-dimethyl-1-hydroxypyrrole, the fourth group, concentration obviously increased in the EC process, but was completely removed in the UASB reactor. The content of volatile fatty acids (VFAs) markedly increased from 0.68% in the leachate to 16.18% in the effluent from the electrochemical oxidation process (EC(effl)). In addition, the degradation rate of organic compounds from the landfill leachate was different in the EC oxidation and anaerobic process.     

Fenton氧化对制浆造纸废水分子量及可生化性变化的影响

以制浆造纸废水的初沉池出水为研究对象,对不同剂量的Fenton氧化试剂处理制浆造纸厂初沉废水的效果进行了研究,初沉废水中的分子量大于10 000的有机污染物含量占到83%,废水可生化性较差;在Fe2+与H2O2的摩尔比为1∶5,废水pH为3.5的条件下,H2O2(30%)投加量小于3.25 mL/L时,Fenton试剂的氧化效率更高;H2O2(30%)投加量为6.50 mL/L时,废水中污染物的去除率更高,其中废水COD的去除率为79.5%,AOX的去除率为75.3%,色度去除率为97.5%,同时处理后废水中分子量在500~3 000之间的有机物含量占到82.98%,废水的BOD5/COD值提高到0.56。Fenton氧化作为前置技术处理制浆造纸废水,可以降低废水中的有机物分子量,减少废水的生物毒性,增加废水生物降解性,有助于后续生物处理的正常运行。     

不同高级氧化法对水中低浓度药物甲硝唑降解过程的比较

采用UV、H₂O₂、UV/H₂O₂、Fenton、UV/Fenton和UV/TiO₂方法，对水中低浓度的药物甲硝唑进行降解。通过HPLC和UV-Vis光谱得到的甲硝唑去除率。详细讨论了Fe²⁺、TiO₂和H₂O₂的初始浓度以及溶液的初始pH值对降解效率的影响。结果表明，UV/Fenton和UV/TiO₂ 2种系统对水中低浓度甲硝唑均有很好的去除效果，但前者的光催化效率更高。在甲硝唑浓度=6 μmol/L，H₂O₂和Fe²⁺的初始浓度分别为0.5 mg/L和2.94 μmol/L，pH=4的条件下，UV/Fenton方法对甲硝唑水溶液光催化的最佳效率为95.8%。     

Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.